| 編號 | 中文名稱 | 英文名稱 |
|---|
| ISO 12156-1-2006
| 柴油.使用高頻往復裝置(HFRR)進行潤滑油評定.第1部分:試驗方法
| Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Part 1: Test method
|
| ISO 12156-2-2007
| 柴油.使用高頻往復裝置(HFRR)進行潤滑評估.第2部分:限值
| Diesel fuel - Assessment of lubricity using the high-frequency reciprocating rig (HFRR) - Part 2: Limit
|
| ISO 12345-2002
| 柴油發動機.燃料噴射設備的清潔度評定
| Diesel engines - Cleanliness assessment of fuel injection equipment
|
| ISO 13296-2005
| 柴油發動機.高壓燃料噴射管組件.一般要求和尺寸
| Diesel engines - High-pressure fuel injection pipe assemblies - General requirements and dimensions
|
| ISO 13555-1-2003
| 柴油發動機.柴油噴注設備動態計時的檢驗規程.第1部分:預調節
| Diesel engines - Procedure for checking the dynamic timing of diesel fuel injection equipment - Part 1: Preconditioning
|
| ISO 13555-2-2003
| 柴油發動機.柴油噴注設備動態計時的檢驗規程.第2部分:試驗方法
| Diesel engines - Procedure for checking the dynamic timing of diesel fuel injection equipment - Part 2: Test method
|
| ISO 13555-3-2004
| 柴油發動機.柴油噴射裝置動態計時的檢驗規程.第3部分:時間測量設備的檢測
| Diesel engines - Procedure for checking the dynamic timing of diesel fuel injection equipment - Part 3: Validation of timing measurement devices
|
| ISO 13759-1996
| 石油產品 柴油中硝酸烷基酯含量的測定 分光光度法
| Petroleum products - Determination of alkyl nitrate in diesel fuels - Spectrometric method
|
| ISO 13948-1-2000
| 柴油機 燃料噴射泵和燃料噴射器低壓連接 第1部分:螺紋連接件
| Diesel engines - Fuel injection pumps and fuel injector low-pressure connections - Part 1: Threaded connections
|
| ISO 13948-2-2000
| 柴油機 燃料噴射泵和燃料噴射器低壓連接 第2部分:無螺紋(推進式)連接件
| Diesel engines - Fuel injection pumps and fuel injector low-pressure connections - Part 2: Non-threaded (push-on) connections
|
| ISO 14681-1998
| 柴油機 燃料噴射泵試驗 燃料噴射器的校正
| Diesel engines - Fuel injection pump testing - Calibration fuel injectors
|
| ISO 16147-2002
| 小艇.艇內柴油發動機.裝在發動機上的燃油和電氣元件
| Small craft - Inboard diesel engines - Engine-mounted fuel and electrical components
|
| ISO 19013-1-2005
| 內燃機燃料回路用橡膠軟管和管.規范.第1部分:柴油
| Rubber hoses and tubing for fuel circuits for internal combustion engines - Specification - Part 1: Diesel fuels
|
| ISO 19438-2003
| 內燃機用柴油燃料和汽油過濾器.用粒子計數及污物滯留量評定過濾效率
| Diesel fuel and petrol filters for internal combustion engines - Filtration efficiency using particle counting and contaminant retention capacity
|
| ISO 20844-2004
| 石油和相關產品.用柴油噴射器噴嘴測定含高聚物油的剪切穩定性
| Petroleum and related products - Determination of the shear stability of polymer-containing oils using a diesel injector nozzle
|
| ISO 21487-2006
| 小艇.永久性安裝的汽油和柴油燃油罐
| Small craft - Permanently installed petrol and diesel fuel tanks
|
| ISO 22241-1-2006
| 柴油發動機.AUS 32型NOx還原劑.第1部分:質量要求
| Diesel engines - NOx reduction agent AUS 32 - Part 1: Quality requirements
|
| ISO 22241-2-2006
| 柴油機.NOx還原劑AUS 32.第2部分:試驗方法
| Diesel engines - NOx reduction agent AUS 32 - Part 2: Test methods
|
| ISO 2697-1999
| 柴油機 噴油嘴偶件 “S”尺寸
| Diesel engines - Fuel nozzles - Size "S"
|
| ISO 2698-1993
| 柴油機 柴油機噴油器件 7型和28型
| Diesel engines; clamp-mounted fuel injectors, types 7 and 28
|
| ISO 2699-1994
| 柴油機 法蘭安裝式“S”號噴油嘴 2、3、4、5和6型
| Diesel engines; flange-mounted fuel injectors, size "S"; types 2, 3, 4, 5 and 6
|
| ISO 2974-2005
| 柴油機.60度錐孔的高壓油管接頭管端部連接
| Diesel engines - High-pressure fuel injection pipe end-connections with 60 degrees female cone
|
| ISO 4010-1998
| 柴油機 軸針式標準噴油嘴偶件
| Diesel engines - Calibrating nozzle, delay pintle type
|
| ISO 4020-2001
| 道路車輛 柴油機過濾器 試驗方法
| Road vehicles - Fuel filters for diesel engines - Test methods
|
| ISO 4093-1999
| 柴油機 噴油泵 試驗臺用高壓油管
| Diesel engines - Fuel injection pumps - High-pressure pipes for testing
|
| ISO 4113-1988
| 道路車輛 柴油機噴油泵的校泵油
| Road vehicles; calibration fluid for diesel injection equipment
|
| ISO 5165-1998
| 石油產品 柴油著火性能的測定 十六烷值法
| Petroleum products - Determination of the ignition quality of diesel fuels - Cetane engine method
|
| ISO 6519-2004
| 柴油機.噴油泵.軸端和轂盤的錐度
| Diesel engines - Fuel injection pumps - Tapers for shaft ends and hubs
|
| ISO 7026-1997
| 柴油機 S尺寸軸針式噴油嘴偶件B型擰入式噴嘴器件(20、21、21.1和27型)
| Diesel engines - Screw-in injection nozzle holders, types 20, 21, 21.1 and 27 for pintle nozzle size "S", type "B"
|
| ISO 7299-1-2007
| 柴油機.泵用端面安裝法蘭盤.第1部分:燃料油噴射泵
| Diesel engines - End-mounting flanges for pumps - Part 1: Fuel injection pumps
|
| ISO 7299-1996
| 柴油機 噴油泵端面法蘭
| Diesel engines - End-mounting flanges for fuel injection pumps
|
| ISO 7310-1993
| 柴油機 有水平法蘭盤的旋轉式燃油濾清器頂蓋 安裝和連接尺寸
| Diesel engines; heads for spin-on fuel filters with horizontal flange; mounting and connecting dimensions
|
| ISO 7311-1993
| 柴油機 有垂直法蘭盤的燃油濾清器頂蓋 安裝和連接尺寸
| Diesel engines; heads for fuel filters with vertical flange; mounting and connecting dimensions
|
| ISO 7654-1998
| 道路車輛 柴油發動機用旋裝式燃油濾清器 裝配和連接尺寸
| Road vehicles - Spin-on fuel filters for diesel engines - Mounting and connecting dimensions
|
| ISO 7879-1997
| 柴油機 柱塞式噴油泵 安裝尺寸
| Diesel engines - Cradle-mounted in-line fuel injection pumps - Mounting dimensions
|
| ISO 8356-1984
| 道路車輛 柴油機 22型螺旋擰入式噴油器
| Road vehicles; Diesel engines; Screw-in injector, type 22
|
| ISO 8535-1-2006
| 柴油發動機.高壓噴射燃油管用鋼管.第1部分:無縫冷拉制單壁鋼管的要求
| Diesel engines - Steel tubes for high-pressure fuel injection pipes - Part 1: Requirements for seamless cold-drawn single-wall tubes
|
| ISO 8861-1998
| 造船 柴油機船舶機艙通風 設計要求和計算基準
| Shipbuilding - Engine-room ventilation in diesel-engined ships - Design requirements and basis of calculations
|
| ISO 8984-1-1993
| 柴油機 噴油器試驗 第1部分:手壓試驗和調整裝置
| Diesel engines; testing of fuel injectors; part 1: hand-lever-operated testing and setting apparatus
|
| ISO 8984-2-1993
| 柴油機 噴油器試驗 第2部分:試驗程序
| Diesel engines; testing of fuel injectors; part 2: test methods
|
| ISO 9102-1997
| 柴油機 壓燃式發動機用24、25、26和26 1型螺旋擰入式噴油器
| Diesel engines - Screw-in injection nozzle holders, types 24, 25, 26 and 26.1
|
| ISO 9159-1988
| 道路車輛 含鉛汽油和柴油用管嘴
| Road vehicles; nozzle spouts for leaded gasoline and diesel fuel
|
| ISO 9310-1987
| 道路車輛 壓燃式(柴油)發動機的煙度測量 對快速路檢的概括
| Road vehicles; Smoke measurement of compression-ignition (diesel) engines; Survey of short in-service tests
|
| ISO/TS 16332-2006
| 柴油機.柴油濾清器.燃料/水分離效果評定方法
| Diesel engines - Fuel filters - Method for evaluating fuel/water separation efficiency
|
| ISO/TS 23556-2007
| 去除潤滑油中柴油機煙灰用裝置的性能試驗方法.初始過濾效率
| Performance test method for diesel engine soot-removal devices in lubricating oils - Initial filtration efficiency
|
| 編號 | 中文名稱 | 英文名稱 |
|---|