| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| ANSI/ASTM D2802-2003 | 電線和電纜用耐臭氧乙丙橡膠絕緣材料規范 | Specification for Ozone-Resistant Ethylene-Propylene Rubber Insulation for Wire and Cable |
| ANSI/ASTM D4245-2002 | 工作溫度為90℃干/75℃濕的電線和電纜的耐臭氧熱塑性合成橡膠絕緣規范 | Specification for Ozone-Resistant Thermoplastic Elastomer Insulation for Wire and Cable 90oC Dry/75oC Wet Operation |
| ANSI/ASTM D4246-2002 | 工作溫度為90℃的電線和電纜的耐臭氧熱塑性合成橡膠絕緣規范 | Specification for Ozone-Resistant Thermoplastic Elastomer Insulation for Wire and Cable, 90oC Operation |
| ANSI/EIA 364-14B-1999 | 電連接器.臭氧暴露試驗程序 | Ozone Exposure Test Procedure for Electrical Connectors |
| ANSI/EIA-364-14B-1999 | 電連接器.臭氧暴露試驗程序 | Ozone Exposure Test Procedure for Electrical Connectors |
| ANSI/NSF 222-2006 | 臭氧發生器 | NSF 222 - Ozone Generators |
| ASTM D1149-2007 | 臭氧可控環境中橡膠變壞龜裂的標準試驗方法 | Standard Test Methods for Rubber Deterioration-Cracking in an Ozone Controlled Environment |
| ASTM D2802-2003 | 電線及電纜用耐臭氧乙烯烴聚合物絕緣材料的標準規范 | Standard Specification for Ozone-Resistant Ethylene-Alkene Polymer Insulation for Wire and Cable |
| ASTM D3156-1996(2005) | 橡膠的標準實施規程.防降解劑(防氧化劑、防臭氧劑及穩定劑)的色譜分析 | Standard Practice for Rubber&8212;Chromatographic Analysis of Antidegradants (Antioxidants, Antiozonants and Stabilizers) |
| ASTM D4246-2002 | 在90℃時電線和電纜的耐臭氧熱塑性彈性體絕緣的標準規范 | Standard Specification for Ozone-Resistant Thermoplastic Elastomer Insulation For Wire and Cable, 90&176C Operation |
| ASTM D4575-1999(2005) | 橡膠變質的標準試驗方法.測定實驗室測試小室內臭氧濃度的參照法和交替法 | Standard Test Methods for Rubber Deterioration&8212;Reference and Alternative Method(s) for Determining Ozone Level in Laboratory Test Chambers |
| ASTM D5011-1992(2003) | 使用傳送標準對臭氧檢測器的校驗 | Standard Practices for Calibration of Ozone Monitors Using Transfer Standards |
| ASTM D5110-1998(2004) | 使用紫外光度法進行臭氧轉變標準認證和臭氧監測器校準的標準實施規范 | Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry |
| BS 1747-12-1993 | 空氣污染測量方法.環境空氣中臭氧質量濃度的測定:化學熒光法 | Methods for measurement of air pollution - Determination of the mass concentration of ozone in ambient air: chemiluminescence method |
| BS EN 1278-1999 | 供人用的水處理時用的化學物質.臭氧 | Chemicals used for treatment of water intended for human consumption - Ozone |
| BS EN 14625-2005 | 環境空氣質量.用紫外線光度測量法測量臭氧濃度的標準方法 | Ambient air quality - Standard method for the measurement of the concentration of ozone by ultraviolet photometry |
| BS EN 15074-2008 | 游泳池水處理用化學試劑.臭氧 | Chemicals used for treatment of swimming pool water - Ozone |
| BS EN 1844-2001 | 防水柔性板.耐臭氧性測定.屋頂防水用塑料和橡膠薄板 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing |
| BS EN 2349-409-2007 | 航空航天系列.繼電器和電流接觸器的要求和試驗程序.抗臭氧 | Aerospace series — Requirements and test procedures for relays and contactors — Part 409: Ozone resistance |
| BS EN 2591-316-1998 | 光電連接元件.試驗方法.耐臭氧 | Elements of electrical and optical connection - Test methods - Ozone resistance |
| BS EN 2591-6316-2001 | 電氣和光學連接元件.試驗方法.光學元件.耐臭氧性能 | Elements of electrical and optical connection - Test methods - Optical elements - Ozone resistance |
| BS EN 60811-2-1-1998 | 電纜絕緣和護套材料.通用試驗方法.彈性化合物專用試驗方法.耐臭氧性、熱固化及礦物油浸漬試驗 | Insulating and sheathing materials of electric cables - Common test methods - Methods specific to elastomeric compounds - Methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests |
| BS EN ISO 105-G03-1997 | 紡織品.色牢度試驗.第G03部分:耐大氣臭氧色牢度 | Textiles - Tests for colour fastness - Colour fastness to ozone in the atmosphere |
| BS EN ISO 10960-1997 | 橡膠和塑料軟管.在動態條件下耐臭氧性的評定 | Rubber and plastic hoses - Assessment of ozone resistance under dynamic conditions |
| BS EN ISO 15011-2-2003 | 焊接和相關工藝的衛生和安全.電弧焊產生的煙和氣體取樣的實驗室法.除臭氧外的氣體排放率的測定 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Determination of emission rates of gases, except ozone |
| BS EN ISO 7326-2008 | 橡膠和塑料軟管.靜態條件下評定耐臭氧性 | Rubber and plastics hoses - Assessment of ozone resistance under static conditions |
| BS ISO 1431-1-2004 | 硫化橡膠或熱塑性橡膠.耐臭氧龜裂性.靜態和動態應變試驗 | Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Static and dynamic strain testing |
| BS ISO 1431-3-2000 | 硫化橡膠或熱塑橡膠.耐臭氧龜裂性.在實驗室試驗測定臭氧濃度的標準方法和替用方法 | Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Reference and alternative methods for determining the ozone concentration in laboratory test chambers |
| BS ISO 3011-1997 | 橡膠或塑料涂層織物.靜態條件下抗臭氧龜裂的測定 | Rubber- or plastics-coated fabrics - Determination of resistance to ozone cracking under static conditions |
| DIN 19627-1993 | 水處理用臭氧設備 | Ozone-plants for water treatment |
| DIN 19643-3-1997 | 游泳池和洗浴用水的處理.第3部分:處理方法組合:絮凝作用、過濾作用、臭氧消毒處理、吸附過濾和氯化作用 | Treatment of water of swimming-pools and baths - Part 3: Combination of process: Flocculation, filtration, ozonization, absorbing filtration, chlorination |
| DIN 19643-4-1999 | 游泳池和洗澡池水的處理.第4部分:方法組合:絮凝作用、臭氧消毒法、多層過濾和氯化作用 | Treatment of water of swimming pools and baths - Part 4: Combination of process: Flocculation, ozonisation, multilayer filtration, chlorination |
| DIN 38408-3-1993 | 德國檢驗水、廢水和污泥的標準方法.氣態組份(G組),臭氧的測定(G 3) | German standard methods for the examination of water, waste water and sludge; gaseous components (group G); determination of ozone (G 3) |
| DIN 53509-1-2001 | 橡膠試驗.抗臭氧龜裂的測定.第1部分:靜態條件 | Testing of rubber - Determination of resistance to ozone cracking - Part 1: Static conditions |
| DIN 53509-2-1994 | 橡膠的檢驗.抗臭氧裂化的測定.第2部分:在試驗室測試間測定臭氧濃度的基準方法 | Testing of rubber - Determination of resistance to ozone cracking - Part 2: Reference method for determining ozone concentration in laboratory test chambers |
| DIN EN 1278-1999 | 飲用水處理用化學品.臭氧 | Chemicals used for treatment of water intended for human consumption - Ozone; German version EN 1278:1998 |
| DIN EN 14625-2005 | 環境空氣質量.用紫外線光度測量法測量臭氧濃度的標準方法 | Ambient air quality - Standard method for the measurement of the concentration of ozone by ultraviolet photometry; German version EN 14625:2005 |
| DIN EN 15074-2006 | 游泳池水處理用化學制品.臭氧 | Chemicals used for treatment of swimming pool water - Ozone English version of DIN EN 15074:2006-08 |
| DIN EN 1844-2001 | 防水軟板.耐臭氧性測定.屋頂防水塑料和橡膠薄板 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing; German version EN 1844:2001 |
| DIN EN 2349-409-2008 | 航空航天系列.繼電器和電流接觸器的要求和試驗程序.第409部分:耐臭氧性 | Aerospace series - Requirements and test procedures for relays and contactors - Part 409: Ozone resistance; German and English version EN 2349-409:2007 |
| DIN EN 2591-316-1997 | 航空航天系列.光電連接件.試驗方法.第316部分:耐臭氧 | Aerospace series - Elements of electrical and optical connection; test methods - Part 316: Ozone resistance; German version EN 2591-316:1997 |
| DIN EN 2591-6316-2003 | 航空航天系列.光電連接件.試驗方法.第6316部分:光學元件.耐臭氧性 | Aerospace series - Elements of electrical and optical connection; Test methods - Part 6316: Optical elements; Ozone resistance; German and English version EN 2591-6316:2001 |
| DIN EN 27326-1993 | 橡膠和塑料軟管.靜態條件下耐臭氧性能的評定 | Rubber and plastics hoses; assessment of ozone resistance under static conditions (ISO 7326:1991); German version EN 27326:1993 |
| DIN EN 60811-2-1-2002 | 電纜和光纜的絕緣和護套材料.通用試驗方法.第2-1部分:彈性體專用試驗方法.耐臭氧性、熱固和礦物油浸試驗 | Insulating and sheathing materials of electric and optical cables - Common test methods - Part 2-1: Methods specific to elastomeric compounds; Ozone resistance, hot set and mineral oil immersion tests (IEC 60811-2-1:1998 + A1:2001); German version EN 60811-2-1:1998 + A1:2001 |
| DIN EN ISO 105-G03-1997 | 紡織品.色牢度試驗.第G03部分:耐大氣臭氧色牢度測定 | Textiles - Tests for colour fastness - Part G03: Colour fastness to ozone in the atmosphere (ISO 105-G03:1993); German version EN ISO 105-G03:1997 |
| DIN EN ISO 10960-1996 | 橡膠和塑料軟管.動態耐臭氧性評估 | Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions (ISO 10960:1994); German version EN ISO 10960:1996 |
| DIN EN ISO 15011-2-2003 | 焊接和相關工藝中的保健和安全.對電弧焊產生的煙塵和氣體取樣的實驗室方法.第2部分:除臭氧外氣體的排放率的 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2: Determination of emission rates of gases, except ozone (ISO 15011-2:2003); German version EN ISO 15011-2:2003 |
| DIN EN ISO 15011-3-2003 | 焊接和相關工藝的衛生和安全.電弧焊煙和氣體的實驗室取樣法.第3部分:固定點法測定臭氧濃度 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 3: Determination of ozone concentration using fixed point measurements (ISO 15011-3:2002); German version EN ISO 15011-3:2002 |
| DIN ISO 13964-1999 | 空氣質量.環境空氣中臭氧含量測定.紫外分光光度法 | Air quality - Determination of ozone in ambient air - Ultraviolet photometric method (ISO 13964:1998) |
| EN 1278-1998 | 民用水處理用化學藥劑 臭氧 | Chemicals used for treatment of water intended for human consumption - Ozone |
| EN 1278/prA1-2000 | 民用水處理用化學藥劑 臭氧 修正A1 | Chemicals used for treatment of water intended for human consumption - Ozone; Amendment A1 |
| EN 1844-2001 | 防水熱塑性及彈性薄板 耐臭氧性的測定 屋頂防水用塑料和橡膠薄板 | Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing |
| EN 2591-316-1997 | 航空航天系列 光電連接元件 試驗方法 第316部分：抗臭氧 | Aerospace series - Elements of electrical and optical connection - Test methods - Part 316: Ozone resistance |
| EN 2591-6316-2001 | 航空航天系列 光電連接元件 試驗方法 第6316部分：光學元件 耐臭氧 | Aerospace series - Elements of electrical and optical connection; Test methods - Part 6316: Optical elements; Ozone resistance |
| EN 27326-1993 | 橡膠和塑料軟管 靜態條件下耐臭氧性的評定 | Rubber and plastics hoses-Assessment of ozone resistance under static conditions (ISO 7326:1991) |
| EN 60811-2-1-1998+A1-2001 | 電纜絕緣和護套材料 通用試驗方法 第2-1部分：合成橡膠專用方法 抗臭氧試驗 熱固試驗和礦物油浸試驗 | Insulating and sheathing materials of electric and optical cables - Common test methods - Part 2-1: Methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests (IEC 60811-2-1:1998) |
| EN ISO 105-G03-1997 | 紡織品 色牢度試驗 第G03部分：耐大氣臭氧色牢度 | Textiles - Tests for colour fastness - Part G03: Colour fastness to ozone in the atmosphere (ISO 105-G03:1993) |
| EN ISO 10960-1996 | 橡膠和塑料軟管 動態條件下耐臭氧性的評定 | Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions (ISO 10960:1994) |
| EN ISO 15011-2-2003 | 焊接和有關工藝中的健康和安全 電弧焊產生的煙塵和氣體取樣的實驗室方法 第2部分：除臭氧外、各種氣體產 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2: Determination of emission rates of gases, except ozone (ISO 15011-2:2003) |
| EN ISO 15011-3-2002 | 焊接和有關工藝中的健康和安全 電弧焊產生的煙塵和氣體取樣的實驗室方法 第3部分：在固定點測定臭氧濃度 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 3: Determination of ozone concentration using fixed point measurements (ISO 15011-3:2002) |
| GB 18066-2000 | 居住區大氣中臭氧衛生標準 | Hygienic standard for ozone in air of residential areas |
| GB/T 11039.3-2005 | 紡織品 色牢度試驗 耐大氣污染物色牢度 第3部分:大氣臭氧 | Textiles-Tests for colour fastness-Colour fastness to Contaminants part3:ozone in the atmosphere |
| GB/T 13642-1992 | 硫化橡膠耐臭氧老化試驗動態拉伸試驗法 | Rubber，vulcanized--Resistance to ozone ageing--Dynamic strain test method |
| GB/T 15437-1995 | 環境空氣臭氧的測定靛藍二磺酸鈉分光光度法 | Ambient air--Determination of ozone--Indigo disulphonate spectrophotometry |
| GB/T 15438-1995 | 環境空氣臭氧的測定紫外光度法 | Ambient air--Determination of ozone--Ultraviolet photometric method |
| GB/T 18202-2000 | 室內空氣中臭氧衛生標準 | Hygienic standard for ozone in indoor air |
| GB/T 18204.27-2000 | 公共場所空氣中臭氧測定方法 | Method of examination of ozone in air of public places |
| GB/T 18949-2003 | 橡膠和塑料軟管動態條件下耐臭氧性能的評定 | Rubber and plastics hoses--Assessment of ozone resistance under dynamic conditions |
| GB/T 24134-2009 | 橡膠和塑料軟管 靜態條件下耐臭氧性能的評價 | () |
| GB/T 2951.21-2008 | 電纜和光纜絕緣和護套材料通用試驗方法 第21部分：彈性體混合料專用試驗方法 耐臭氧試驗-熱延伸試驗-浸礦物 | Common test methods for insulating and sheathing materials of electric and optical cables - Part 21:Methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests |
| GB/T 7762-2003 | 硫化橡膠或熱塑性橡膠耐臭氧龜裂靜態拉伸試驗 | Rubber，vulcanized or thermoplastic--Resistance to ozone cracking--Static strain test |
| HG/T 2716-2008 | 橡膠或塑料涂覆織物 靜態耐臭氧龜裂性能的測定 | () |
| HG/T 2869-1997 | 橡膠和塑料軟管 靜態條件下耐臭氧性能的評價 | () |
| IEC 60811-2-1 AMD 1-2001 | 電纜和光纜用絕緣和護套材料 通用試驗方法 第2-1部分:彈性化合物專用方法 耐臭氧試驗、熱凝固試驗和礦物 | Common test methods for insulating and sheathing materials of electric and optical cables - Part 2-1: Methods specific to elastomeric compounds; Ozone resistance, hot set and mineral oil immersion tests; Amendment 1 |
| IEC 60811-2-1 Edition 2.1-2001 | 電纜和光纜用絕緣和屏蔽材料的共同試驗方法.第2-1部分:彈性體所用特定方法.臭氧抗性、熱固和礦物油浸試驗 | Common test methods for insulating and sheathing materials of electric and optical cables - Part 2-1: Methods specific to elastomeric compounds; Ozone resistance, hot set and mineral oil immersion tests |
| IEC 60811-2-1-1998 | 電纜和光纜用絕緣和護套材料 通用試驗方法 第2-1部分:彈性化合物專用方法 耐臭氧試驗、熱凝固試驗和礦物油 | Insulating and sheathing materials of electric and optical cables - Common test methods - Part 2-1: Methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests |
| ISO 10313-1993 | 環境空氣 臭氧質量濃度的測定 化學發光法 | Ambient air; determination of the mass concentration of ozone; chemiluminescence method |
| ISO 105-G03-1993 | 紡織品 色牢度試驗 第G03部分:耐大氣臭氧色牢度 | Textiles; tests for colour fastness; part G03: colour fastness to ozone in the atmosphere |
| ISO 10960-1994 | 橡膠和塑料軟管 動態條件下耐臭氧性的評定 | Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions |
| ISO 13964-1998 | 空氣質量 環境空氣中臭氧的測定 紫外分光光度法 | Air quality - Determination of ozone in ambient air - Ultraviolet photometric method |
| ISO 1431-1-2004 | 硫化或熱塑性橡膠.耐臭氧龜裂.第1部分:靜態和動態應變試驗 | Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Part 1: Static and dynamic strain testing |
| ISO 1431-3-2000 | 硫化或熱塑性橡膠 耐臭氧龜裂 第3部分:實驗室試驗箱內測定臭氧濃度的推薦的和可選用的方法 | Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Part 3: Reference and alternative methods for determining the ozone concentration in laboratory test chambers |
| ISO 15011-2-2003 | 焊接和相關工藝中的保健和安全.對電弧焊產生的煙塵和氣體取樣的實驗室方法.第2部分:除臭氧外氣體的排放率的 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2: Determination of emission rates of gases, except ozone |
| ISO 3011-1997 | 橡膠或塑料涂覆織物 靜態條件下抗臭氧龜裂的測定 | Rubber- or plastics-coated fabrics - Determination of resistance to ozone cracking under static conditions |
| ISO 6235-1995 | 生膠 嵌段聚苯乙烯含量的測定 臭氧分解法 | Rubber, raw - Determination of block polystyrene content - Ozonolysis method |
| ISO 7326-2006 | 橡膠和塑料軟管.靜態條件下評定耐臭氧性 | Rubber and plastics hoses - Assessment of ozone resistance under static conditions |
| JC/T 426-1998 | 無臭氧石英玻璃管 | () |
| JIS B7957-2006 | 環境空氣中臭氧和氧化劑的連續分析儀 大気中のオゾン及びオキシダントの自動計測器 | Continuous analyzers for ozone and oxidants in ambient air |
| JIS C3660-2-1-2003 | 電纜和光纜的絕緣和鎧裝材料的通用試驗方法.第2-1部分:彈性復合物專用方法.耐臭氧、熱固及礦物油浸漬試驗 電気?光ケーブルの絶縁體及びシース材料の共通試験方法 ― 第２－１部：エラストマーの特性試験方法 ― オゾン，ホットセット及び耐油試験 | Common test methods for insulating and sheathing materials of electric and optical cables -- Part 2-1: Methods specific to elastomeric compounds -- Ozone resistance, hot set and mineral oil immersion tests |
| JIS K6259-2004 | 硫化或熱塑性橡膠.耐臭氧的測定 加硫ゴム及び熱可塑性ゴム―耐オゾン性の求め方 | Rubber, vulcanized or thermoplastics -- Determination of ozone resistance |
| JIS K6330-7-1998 | 橡膠和塑料軟管的測試方法.第7部分:靜態條件下對臭氧抗性的評估 ゴム及び樹脂ホース試験方法 ― 第７部：靜的オゾン劣化試験 | Testing methods for rubber and plastics hoses -- Part 7: Assessment of ozone resistance under static conditions |
| JIS K6404-19-1999 | 橡膠或塑料涂覆織物的試驗方法.第19部分:耐臭氧龜裂的測定 ゴム引布?プラスチック引布試験方法 ― 第１９部：オゾン劣化試験 | Testing methods for rubber-or plastics-coated fabrics -- Part 19: Determination of resistance to ozone cracking |
| JIS L0890-2006 | 臭氧色牢度的試驗方法 オゾンに対する染色堅ろう度試験方法 | Test methods for colour fastness to ozone |
| JIS X6936-2005 | 信息技術.辦公室設備.復印機、打印機和多功能設備的臭氧、揮發性有機化合物和灰塵的散發率測量 事務機器－オゾン，揮発性有機化合物及び粉じんの放散量測定方法 | Information technology -- Office equipment -- Measurement of ozone, volatile organic compounds and dust emissions rate from copiers, printers and multi-function devices |
| NF A88-200-2-2003 | 焊接和相關工藝中的衛生和安全.對電弧焊產生的煙塵和氣體取樣的實驗室方法.第2部分:除臭氧外氣體的排放率測 | (Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 2 : determination of emission rates of gases, except ozone.) |
| NF A88-200-3-2003 | 焊接和相關工藝中的衛生和安全.對電弧焊產生的煙塵和氣體取樣的實驗室方法.第3部分:用固定點測量法測定臭氧 | (Health and safety in welding and allied processes - Laboratory method for sampling fume and gases generated by arc welding - Part 3 : determination of ozone concentration using fixed point measurement) |
| NF C32-028-1999 | 電纜和光纜用絕緣和屏蔽材料.一般試驗方法.第2-1部分:彈性體所用特定方法.臭氧抗性,熱固和礦物油浸試驗 | (Insulating and sheating materials of electric and optical cables - Common test methods - Part 2-1 : methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tests.) |
| NF C32-028/A1-2002 | 電纜和光纜用絕緣材料和護套材料.通用試驗方法.第2-1部分:專用于彈性化合物的方法.耐臭氧性、熱固和礦物油 | (Insulating and sheathing materials of electric and optical cables - Common test methods - Part 2-1 : methods specific to elastomeric compounds - Ozone resistance, hot set and mineral oil immersion tes) |
| NF G07-071-3-1997 | 紡織.色牢度試驗.第G03部分:大氣中耐臭氧色牢度(歐洲標準EN ISO 105-G03) | (TEXTILES. TESTS FOR COLOUR FASTNESS. PART G03 : COLOUR FASTNESS TO OZONE IN THE ATMOSPHERE. (EUROPEAN STANDARD EN ISO 105-G03).) |
| NF G37-112-1980 | 橡膠或塑料涂層織物.抗臭氧的靜態試驗 | (Fabrics coated with rubber or plastic-static ozone resistance test.) |
| NF L54-002-035-1998 | 航空航天系列.電氣及光學連接的元件.試驗方法.第316部分:臭氧抗性 | (Aerospace series. Elements of electrical and optical connection. Test methods. Part 316 : ozone resistance.) |
| NF L54-002-119-2002 | 航空航天系列.電氣及光學連接元件.試驗方法.第6316部分:光學元件.耐臭氧性 | (Aerospace series - Elements of electrical and optical connection - Test methods - Part 6316 : optical elements - Ozone resistance.) |
| NF P84-112-2002 | 防水軟板.耐臭氧性測定.屋頂防水用塑料和橡膠薄板 | (Flexible sheets for waterproofing - Determination of resistance to ozone - Plastic and rubber sheets for roof waterproofing.) |
| NF T46-019-1992 | 硫化或熱塑橡膠.抗臭氧開裂.靜態變形試驗 | (Vulcanized or thermoplastic rubber. Resistance to ozone cracking. Static elongation test.) |
| NF T46-038-1995 | 硫化或熱塑橡膠.抗臭氧開裂.實驗室試驗室中臭氧濃度測定用參考法和選擇法 | (Rubber vulcanized of thermoplastic. Resistance to ozone cracking. Reference and alternative methods for determining ozone concentration in laboratory test chambers.) |
| NF T46-039-1992 | 硫化或熱塑橡膠.抗臭氧開裂.動態變形試驗 | (Vulcanized or thermoplastic rubber. Resistance to ozone cracking. Dynamic deformation test.) |
| NF T47-205-1993 | 橡膠和塑料軟管.靜態條件下的耐臭氧性試驗的評定 | (Rubber and platics hoses. Assessment of ozone resistance under static conditions.) |
| NF T47-218-1996 | 橡膠和塑料軟管.在動力條件下耐臭氧性的評定(歐洲標準EN ISO 10960) | (RUBBER AND PLASTICS HOSES. ASSESSMENT OF OZONE RESISTANCE UNDER DYNAMIC CONDITIONS. (EUROPEAN STANDARD EN ISO 10960).) |
| NF T94-306-1998 | 人類用水的處理試劑.臭氧(歐洲標準EN 1278) | (CHEMICALS USED FOR TREATMENT OF WATER INTENTED FOR HUMAN CONSUMPTION. OZONE. (EUROPEAN STANDARD EN 1278).) |
| prEN 2349-409-2000 | 航空航天系列 繼電器和接觸器要求和試驗程序 第409部分：耐臭氧腐蝕性 | Aerospace series - Requirements and test procedures for relays and contactors - Part 409: Ozone resistance |
| 編號 | 中文名稱 | 英文名稱 |