| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| IEC 60068-2-20-2008 | 環境試驗.第2部分:試驗.試驗T:帶導線裝置的可焊接性和焊接熱抵抗性的試驗方法 | Environmental testing - Part 2: Tests - Test T: Test methods for soldeability and resistance to soldering heat of devices with leads |
| IEC 60068-2-58-2005 | 環境試驗.第2-58部分:試驗.試驗Td:表面安裝元器件(SMD)用可焊性、耐金屬化溶融和耐焊接熱的試驗方法 | Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) |
| IEC 60317-35 Edition 1.2-2000 | 繞阻線特殊類型規范.第35部分:155級帶粘合層的可焊接的聚氨酯瓷漆園形銅線 | Specifications for particular types of winding wires - Part 35: Solderable polyurethane enamelled round copper wire, class 155, with a bonding layer |
| IEC 60317-35-1992 | 特種繞組線規范.第35部分:155級有粘結層的可焊接聚氨酯漆包圓銅線 | Specification for particular types of winding wires; part 35: solderable polyurethane enamelled round copper wire, class 155, with a bonding layer |
| IEC 60317-36 Edition 1.2-2000 | 繞阻線特殊類型規范.第36部分:180級帶粘合層的可焊接的聚酯瓷漆園形銅線 | Specifications for particular types of winding wires - Part 36: Solderable polyesterimide enamelled round copper wire, class 180, with a bonding layer |
| IEC 60317-36-1992 | 特種繞組線規范.第36部分:180級帶粘結層的可軟焊接聚酰胺酯漆包圓銅線 | Specifications for particular types of winding wires; part 36: solderable polyesterimide enamelled round copper wire, class 180, with a bonding layer |
| IEC 60317-55-2007 | 特種繞組線規范.第55部分:涂覆聚酰胺的可焊接聚亞安酯漆包圓銅線.180級 | Specifications for particular types of winding wires - Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 180 |
| IEC 60512-12-1-2006 | 電子設備用連接器.試驗和測量.第12-1部分:焊接試驗.試驗12a: 焊料濕浴法測量可焊性 | Connectors for electronic equipment - Tests and measurements - Part 12-1: Soldering tests - Test 12a: Solderability, wetting, solder bath method |
| IEC 60749-20-2008 | 半導體器件.機械和氣候試驗方法.第20部分:SMDs塑料囊狀物抗?jié)駳夂秃附訜岬木C合影響 | Semiconductor devices - Mechanical and climatic test methods - Part 20: Resistance of plastic-encapsulated SMDs to the combined effect of moisture and soldering heat |
| IEC 60947-4-2006 | 電弧焊接設備.第4部分:運行中檢查和試驗 | Arc welding equipment - Part 4: In-service inspection and testing |
| IEC 60974-1-2005 | 弧焊設備.第1部分:焊接電源 | Arc welding equipment - Part 1: Welding power sources |
| IEC 60974-12-2005 | 弧焊設備.第12部分:焊接電纜的耦合器 | Arc-welding equipment - Part 12: Coupling devices for welding cables |
| IEC 60974-2-2007 | 電弧焊接設備.第2部分:液體冷卻系統 | Arc welding equipment - Part 2: Liquid cooling systems |
| IEC 60974-8-2009 | 弧焊設備.第8部分:焊接和等離子切割系統用氣體控制臺 | Arc welding equipment - Part 8: Gas consoles for welding and plasma cutting systems |
| IEC 61076-4-107-2001 | 電子設備用連接器 第4 -107部分：有質量評定的印制板連接器 基本網格為2.0mm，固定件有印制版的焊接終端 | Connectors for electronic equipment - Part 4-107: Printed board connectors with assessed quality; Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations |
| IEC 61188-5-2-2003 | 印制電路板和印制電路板組件.設計和使用.第5-2部分:焊接(焊接區/焊縫)考慮.分立器件 | Printed boards and printed board assemblies - Design and use - Part 5-2: Attachment (land/joint) considerations; Discrete components |
| IEC 61188-5-3-2007 | 印制板和印制板組件.設計和使用.第5-3部分:焊接(焊接區/接縫)考慮.兩面帶有翅形引線的部件 | Printed boards and printed board assemblies - Design and use - Part 5-3: Attachment (land/joint) considerations - Components with gull-wing leads on two sides |
| IEC 61188-5-4-2007 | 印制板和印制板組件.設計和使用.第5-4部分:焊接(焊接區/接縫)考慮.兩面帶有J形引線的部件 | Printed boards and printed board assemblies - Design and use - Part 5-4: Attachment (land/joint) considerations - Components with J leads on two sides |
| IEC 61188-5-5-2007 | 印制板和印制板組件.設計和使用.第5-5部分:焊接(焊接區/接縫)考慮.四面帶有翅形引線的部件 | Printed boards and printed board assemblies - Design and use - Part 5-5: Attachment (land/joint) considerations - Components with gull-wing leads on four sides |
| IEC 61190-1-3 AMD 1-2010 | 電子組件用連接材料.第1-3部分:電子焊接用電子級釬焊合金及有焊劑和無焊劑的固體焊料用要求 | Attachment materials for electronic assembly - Part 1-3: Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solder for electronic soldering applications |
| IEC 61190-1-3-2007 | 電子組件用連接材料.第1-3部分:電子焊接用電子級釬焊合金及有焊劑和無焊劑的固體焊料用要求 | Attachment materials for electronic assembly - Part 1-3: Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications |
| IEC 61191-1-1998 | 印刷電路板組件 第1部分:總規范 使用表面安裝和相關裝配技術的焊接電氣和電子組件的要求 | Printed board assemblies - Part 1: Generic specification - Requirements for soldered electrical and electronic assemblies using surface mount and related assembly technologies |
| IEC 61191-2-1998 | 印刷電路板組件 第2部分:分規范 表面安裝焊接組件的要求 | Printed board assemblies - Part 2: Sectional specification - Requirements for surface mount soldered assemblies |
| IEC 61191-3-1998 | 印刷電路板組件 第3部分:分規范 通孔安裝焊接組件的要求 | Printed board assemblies - Part 3: Sectional specification - Requirements for through-hole mount soldered assemblies |
| IEC 61191-4-1998 | 印刷電路板組件 第4部分:分規范 端點焊接組件的要求 | Printed board assemblies - Part 4: Sectional specification - Requirements for terminal soldered assemblies |
| IEC 61191-6-2010 | 印刷電路板組件.第6部分:球柵陣列和網格陣列的焊接接頭內空隙及測量方法用評定標準 | Printed board assemblies - Part 6: Evaluation criteria for voids in soldered joints of BGA and LGA and measurement method |
| IEC 61192-5-2007 | 焊接電子組件的工藝要求.第5部分:焊接電子組件的再加工、改進和檢修 | Workmanship requirements for soldered electronic assemblies - Part 5: Rework, modification and repair of soldered electronic assemblies |
| IEC 61760-3-2010 | 表面貼裝技術.第3部分:通孔回流(THR)焊接用組件規范的標準方法 | Surface mounting technology - Part 3: Standard method for the specification of components for through hole reflow (THR) soldering |
| IEC 62081-1999 | 弧焊接設備.安裝和使用 | Arc welding equipment - Installation and use |
| IEC 62135-1-2008 | 電阻焊接設備.第1部分:設計、制造和安裝用安全要求 | Resistance welding equipment - Part 1: Safety requirements for design, manufacture and installation |
| IEC 62135-2-2007 | 電阻焊接設備.第2部分:電磁兼容性(EMC)要求 | Resistance welding equipment - Part 2: Electromagnetic compatibility (EMC) requirements |
| IEC 62137-1-1-2007 | 表面安裝技術.表面安裝焊接接縫的環境和耐久性試驗方法.第1-1部分:拉拔強度試驗 | Surface mounting technology - Environmental and endurance test methods for surface mount solder joint - Part 1-1: Pull strength test |
| IEC 62137-1-2-2007 | 表面安裝技術.表面裝配焊接接縫的環境和耐久性試驗方法.第1-2部分:剪切強度試驗 | Surface mounting technology - Environmental and endurance test methods for surface mount solder joint - Part 1-2: Shear strength test |
| IEC/PAS 62174 Edition 1.0-2000 | 通孔固定裝置的焊接溫度抗性 | Resistance to soldering temperature for through-hole mounted devices |
| ISO 10042 Technical Corrigendum 1-2006 | 焊接.鋁和鋁合金的弧焊接頭.缺陷質量分級.技術勘誤1 | Welding - Arc-welded joints in aluminium and its alloys - Quality levels for imperfections; Technical Corrigendum 1 |
| ISO 10042-2005 | 焊接 鋁和鋁合金的弧焊接頭 缺陷質量分級指南 | Welding - Arc-welded joints in aluminium and its alloys - Quality levels for imperfections |
| ISO 10124-1994 | 壓力用途的無縫鋼管和焊接(埋弧焊除外)鋼管 層狀缺陷檢測用超聲檢驗 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes - Ultrasonic testing for the detection of laminar imperfections |
| ISO 10332-1994 | 壓力用途的無縫鋼管和焊接(埋弧焊除外)鋼管 驗證液壓防泄漏用超聲波檢驗 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; ultrasonic testing for verification of hydraulic leak-tightness |
| ISO 10447-2006 | 焊接.點焊、凸焊和有縫焊的剝離和鑿剝離試驗 | Resistance welding - Peel and chisel testing of resistance spot and projection welds |
| ISO 10460-2005 | 儲氣瓶.焊接的碳素鋼儲氣瓶.定期檢驗和試驗 | Gas cylinders - Welded carbon-steel gas cylinders - Periodic inspection and testing |
| ISO 10464-2004 | 氣瓶.液化石油氣(LPG)用可再填充的焊接鋼制氣瓶.周期檢驗和試驗 | Gas cylinders - Refillable welded steel cylinders for liquefied petroleum gas (LPG) - Periodic inspection and testing |
| ISO 10543-1993 | 壓力用無縫及熱拉伸焊接鋼管 全周邊超聲波厚度檢測 | Seamless and hot-stretch-reduced welded steel tubes for pressure purposes; full peripheral ultrasonic thickness testing |
| ISO 10544-1992 | 鋼筋混凝土和制造焊接網用冷軋鋼絲 | Cold-reduced steel wire for the reinforcement of concrete and the manufacture of welded fabric |
| ISO 10656 Technical Corrigendum 1-2000 | 電阻焊接 焊接槍用電源積分變壓器 技術勘誤1 | Electric resistance welding - Integrated transformers for welding guns; Technical Corrigendum 1 |
| ISO 10656-1996 | 電阻焊接 焊接槍用電源積分變壓器 | Electric resistance welding - Integrated transformers for welding guns |
| ISO 10691-2004 | 氣瓶.液化石油氣(LPG)用可再填充的焊接鋼制氣瓶.裝填前后及裝填期間的檢驗規程 | Gas cylinders - Refillable welded steel cylinders for liquified petroleum gas (LPG) - Procedures for checking before, during and after filling |
| ISO 1071-2003 | 焊接耗材.鑄鐵熔焊用涂敷電焊條、焊絲、焊棒和藥芯焊條.分類 | Welding consumables - Covered electrodes, wires, rods and tubular cored electrodes for fusion welding of cast iron - Classification |
| ISO 10763-1994 | 液壓傳動 端面平齊的無縫和焊接型精密鋼管 尺寸及標稱工作壓力 | Hydraulic fluid power - Plain-end, seamless and welded precision steel tubes - Dimensions and nominal working pressures |
| ISO 10799-2001 | 結構鋼 冷成型、焊接、中空結構截面 技術交貨要求 | Structural steels - Cold-formed, welded, structural hollow sections - Technical delivery requirements |
| ISO 10882-1-2001 | 焊接和相關工藝的衛生和安全 操作人員呼吸區域的空氣中懸浮顆粒物及氣體的取樣 第1部分：空氣中懸浮顆粒 | Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator's breathing zone - Part 1: Sampling of airborne particles |
| ISO 10882-2-2000 | 焊接和相關工藝的衛生與安全 工作人員呼吸區域中空氣中懸浮顆粒物及氣體的取樣 第2部分:氣體取樣 | Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator's breathing zone - Part 2: Sampling of gases |
| ISO 11082-1992 | 鋼筋混凝土結構用焊接網認證方案 | Certification scheme for welded fabric for the reinforcement of concrete structures |
| ISO 11496-1993 | 壓力用途的承壓無縫和焊接鋼管 層間不完整性檢查的管端超聲波檢測 | Seamless and welded steel tubes for pressure purposes; ultrasonic testing of tube ends for the detection of laminar imperfections |
| ISO 11611-2007 | 焊接和類似工藝用防護服裝 | Protective clothing for use in welding and allied processes |
| ISO 11970-2001 | 鋼鑄件制造焊接焊接工藝的規范和驗收 | Specification and approval of welding procedures for production welding of steel castings |
| ISO 12094-1994 | 壓力用途的承壓焊接鋼管 焊接鋼管用鋼帶/鋼板分層缺陷檢測用超聲波試驗 | Welded steel tubes for pressure purposes - Ultrasonic testing for the detection of laminar imperfections in strips/plates used in the manufacture of welded tubes |
| ISO 12095-1994 | 壓力用途的承壓無縫和焊接鋼管 液體滲透試驗 | Seamless and welded steel tubes for pressure purposes - Liquid penetrant testing |
| ISO 12096-1996 | 壓力用途的承壓埋弧焊接鋼管 焊縫缺陷檢測用X射線檢查 | Submerged arc-welded steel tubes for pressure purposes - Radiographic testing of the weld seam for the detection of imperfections |
| ISO 12170-1996 | 氣焊設備 焊接及相關工藝用熱塑性軟管 | Gas welding equipment - Thermoplastic hoses for welding and allied processes |
| ISO 12176-2-2008 | 塑料管材和管件.熔解焊接聚乙烯系統用設備.第2部分:電熔焊 | Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 2: Electrofusion |
| ISO 12176-3-2006 | 塑料管材和管件.聚乙烯系統的熔焊接設備.第3部分:操作者標記 | Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 3: Operator's badge |
| ISO 13663-1995 | 壓力用途的承壓焊接鋼管 焊縫周圍分層缺陷檢測用超聲波試驗 | Welded steel tubes for pressure purposes - Ultrasonic testing of the area adjacent to the weld seam for the detection of laminar imperfections |
| ISO 13664-1997 | 壓力用途的承壓無縫和焊接鋼管 管端分層組織缺陷探測用磁粉檢驗 | Seamless and welded steel tubes for pressure purposes - Magnetic particle inspection of the tube ends for the detection of laminar imperfections |
| ISO 13665-1997 | 壓力用途的承壓無縫和焊接鋼管 管身表面缺陷探測用磁粉檢驗 | Seamless and welded steel tubes for pressure purposes - Magnetic particle inspection of the tube body for the detection of surface imperfections |
| ISO 13847 Technical Corrigendum 1-2001 | 石油和天然氣工業.管道輸送系統.管道焊接.技術勘誤1 | Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines; Technical Corrigendum 1 |
| ISO 13847-2000 | 石油和天然氣工業 管道輸送系統 管道的焊接 | Petroleum and natural gas industrie - Pipeline transportation systems - Welding of pipelines |
| ISO 13916-1996 | 焊接 預熱溫度、道間溫度和預熱維持溫度測量的指南 | Welding - Guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature |
| ISO 13918-2008 | 焊接.螺柱電弧焊用螺柱和陶瓷套圈 | Welding - Studs and ceramic ferrules for arc stud welding |
| ISO 13919-1-1996 | 焊接 電子束和激光焊接頭 缺陷的質量分級指南 第1部分:鋼 | Welding - Electron and laser-beam welded joints - Guidance on quality levels for imperfections - Part 1: Steel |
| ISO 13919-2-2001 | 焊接 電子束和激光束焊接接頭 缺陷質量等級指南 第2部分：鋁及其可焊合金 | Welding - Electron and laser beam welded joints; Guidance on quality levels for imperfections - Part 2: Aluminium and its weldable alloys |
| ISO 13920-1996 | 焊接 焊接結構的一般公差 長度和角度的尺寸 形狀和位置 | Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position |
| ISO 13950 Technical Corrigendum 1-2008 | 塑料管和配件.電熔焊接頭的自動識別系統.技術勘誤1 | Plastics pipes and fittings - Automatic recognition systems for electrofusion joints; Technical Corrigendum 1 |
| ISO 13950-2007 | 塑料管和配件.電熔焊接頭的自動識別系統 | Plastics pipes and fittings - Automatic recognition systems for electrofusion joints |
| ISO 14114-1999 | 氣焊設備 焊接、切割及相關工藝用的乙炔匯流系統 一般要求 | Gas welding equipment - Acetylene manifold systems for welding, cutting and allied processes - General requirements |
| ISO 14172-2008 | 焊接消耗品.鎳和鎳合金的手工金屬弧焊用涂敷焊條.分類 | Welding consumables - Covered electrodes for manual metal arc welding of nickel and nickel alloys - Classification |
| ISO 14174-2004 | 焊接消耗品.埋弧焊用助熔劑.分類 | Welding consumables - Fluxes for submerged arc welding - Classification |
| ISO 14175-2008 | 焊接消耗品.熔焊及相關工藝用氣體和氣體混合物 | Welding consumables - Gases and gas mixtures for fusion welding and allied processes |
| ISO 14323-2006 | 電阻點焊和凸焊.焊接破壞試驗.影響剪切試驗和剪切試驗的樣本尺寸和程序 | Resistance spot welding and projection welds - Destructive testing of welds - Specimen dimensions and procedure for impact shear test and cross-tension testing |
| ISO 14327-2004 | 電阻焊接.電阻點焊、凸焊和縫焊用可焊性瓣輪的測定規程 | Resistance welding - Procedures for determining the weldability lobe for resistance spot, projection and seam welding |
| ISO 14329-2003 | 電阻焊接.焊縫的有損檢驗.電阻點焊、滾焊和凸焊焊縫的疲勞類型和幾何學上的測量 | Resistance welding - Destructive tests of welds - Failure types and geometric measurements for resistance spot, seam, and projection welds |
| ISO 14341-2010 | 焊接消耗品.非合金鋼和細粒鋼的金屬氣體保護焊用焊絲和焊接沉積物.分類 | Welding consumables - Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification |
| ISO 14344-2010 | 焊接消耗品.填充物材料和助熔劑的采購 | Welding consumables - Procurement of filler materials and fluxes |
| ISO 14347-2008 | 疲勞.焊接中空部件連接件用設計程序.推薦 | Fatigue - Design procedure for welded hollow-section joints - Recommendations |
| ISO 14372-2000 | 焊接耗材 通過測量擴散氫方法測定手工電弧焊焊條的抗?jié)裥? | Welding consumables - Determination of moisture resistance of manual metal arc welding electrodes by measurement of diffusible hydrogen |
| ISO 14373-2006 | 電阻焊接.無涂層和有涂層低碳鋼的點焊程序 | Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels |
| ISO 14554-1-2000 | 焊接質量要求 金屬材料的電阻焊接 第1部分:完整質量要求 | Quality requirements for welding - Resistance welding of metallic materials - Part 1: Comprehensive quality requirements |
| ISO 14554-2-2000 | 焊接質量要求 金屬材料的電阻焊接 第2部分:基本質量要求 | Quality requirements for welding - Resistance welding of metallic materials - Part 2: Elementary quality requirements |
| ISO 14555-2006 | 焊接.金屬材料的電弧螺栓焊 | Welding - Arc stud welding of metallic materials |
| ISO 14731-2006 | 焊接管理.任務和職責 | Welding coordination - Tasks and responsibilities |
| ISO 14732-1998 | 焊接人員 金屬材料的完全機械化焊接和自動焊接的熔化焊及電阻焊操作人員的資格審查 | Welding personnel - Approval testing of welding operators for fusion welding and of resistance weld setters for fully mechanized and automatic welding of metallic materials |
| ISO 14744-1-2008 | 焊接.電子束焊接機器的驗收檢驗.第1部分:原則和驗收條件 | Welding - Acceptance inspection of electron beam welding machines - Part 1: Principles and acceptance conditions |
| ISO 14744-2-2000 | 焊接 電子束焊接機的驗收檢驗 第2部分:加速電壓特性的測量 | Welding - Acceptance inspection of electron beam welding machines - Part 2: Measurement of accelerating voltage characteristics |
| ISO 14744-3-2000 | 焊接 電子束焊接機的驗收檢驗 第3部分:電子束電流特性的測量 | Welding - Acceptance inspection of electron beam welding machines - Part 3: Measurement of beam current characteristics |
| ISO 14744-4-2000 | 焊接 電子束焊接機的驗收檢驗 第4部分:焊接速度的測量 | Welding - Acceptance inspection of electron beam welding machines - Part 4: Measurement of welding speed |
| ISO 14744-5-2000 | 焊接 電子束焊接機的驗收檢驗 第5部分:偏轉精度的測量 | Welding - Acceptance inspection of electron beam welding machines - Part 5: Measurement of run-out accuracy |
| ISO 14744-6-2000 | 焊接 電子束焊接機的驗收檢驗 第6部分:焊點位置穩定性的測量 | Welding - Acceptance inspection of electron beam welding machines - Part 6: Measurement of stability of spot position |
| ISO 15011-1-2009 | 焊接和相關工藝中的健康和安全.煙塵和氣體的實驗室取樣方法.第1部分:電弧焊產生的煙塵排放率測定和煙塵采集 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 1: Determination of fume emission rate during arc welding and collection of fume for analysis |
| ISO 15011-2-2009 | 焊接和相關工藝中的健康和安全.對電弧焊產生的煙塵和氣體取樣的實驗室方法.第2部分:在電弧焊,切削加工和刨 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 2: Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO<(Index)2>), nitrogen monoxide (NO) and nitrogen dioxide (NO<(Index)2>) during arc welding, cutting and gouging |
| ISO 15011-3-2009 | 焊接和相關工藝的健康和安全.煙和氣體取樣的實驗室法.第3部分:電弧焊時臭氧排放率的測定 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 3: Determination of ozone emission rate during arc welding |
| ISO 15011-4 AMD 1-2008 | 焊接和相關工藝中的健康和安全.煙塵和氣體取樣用實驗室方法.第4部分:煙塵數據單.修改件1 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 4: Fume data sheets; Amendment 1 |
| ISO 15011-4-2006 | 焊接和相關工藝的衛生和安全.煙塵和氣體取樣的實驗室方法.第4部分:煙塵數據單 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 4: Fume data sheets |
| ISO 15012-1-2004 | 焊接和相關工藝中的健康和安全.空氣過濾用設備的試驗和標記要求.第1部分:焊接煙塵分離效率的試驗 | Health and safety in welding and allied processes - Requirements testing and marking of equipment for air filtration - Part 1: Testing of the separation efficiency for welding fume |
| ISO 15012-2-2008 | 焊接和相關工藝中的衛生和安全.空氣過濾設備的要求、測試和標記.第2部分:采集罩和噴嘴的最小空氣體積流率的 | Health and safety in welding and allied processes - Requirements, testing and marking of equipment for air filtration - Part 2: Determination of the minimum air volume flow rate of captor hoods and nozzles |
| ISO 15607 Technical Corrigendum 1-2005 | 金屬材料焊接過程的規范和鑒定.一般規則.技術勘誤1 | Specification and qualification of welding procedures for metallic materials - General rules; Technical Corrigendum 1 |
| ISO 15607-2003 | 金屬材料焊接程序規范和合格鑒定.總則 | Specification and qualification of welding procedures for metallic materials - General rules |
| ISO 15609-1 Technical Corrigendum 1-2005 | 金屬材料焊接過程的規范和鑒定.焊接過程規范.第1部分:電弧焊接.技術勘誤1 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding; Technical Corrigendum 1 |
| ISO 15609-1-2004 | 金屬材料的焊接程序規范和鑒定.焊接程序規范.第1部分:弧焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding |
| ISO 15609-2-2001 | 金屬材料的焊接程序規范和鑒定 焊接程序規范 第2部分：氣焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 2: Gas welding |
| ISO 15609-3-2004 | 金屬材料的焊接程序規范和鑒定.焊接程序規范.第3部分:電子束焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 3: Electron beam welding |
| ISO 15609-4-2009 | 金屬材料焊接工藝規范和條件限制.焊接工藝規范.第4部分:激光束焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 4: Laser beam welding |
| ISO 15609-5-2004 | 金屬材料焊接程序的規范和鑒定.焊接程序規范.第5部分:電阻焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding |
| ISO 15610-2003 | 金屬材料焊接程序規范和合格鑒定.基于試驗焊接消耗品的合格鑒定 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables |
| ISO 15611-2003 | 金屬材料焊接程序規范和合格鑒定.根據已有焊接經驗進行合格鑒定 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience |
| ISO 15612-2004 | 金屬材料的焊接程序規范和鑒定.通過標準焊接程序的采用進行合格鑒定 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure |
| ISO 15613-2004 | 金屬材料的焊接程序規范和鑒定.基于預生產焊接試驗的鑒定 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test |
| ISO 15614-1 AMD 1-2008 | 金屬材料焊接工藝的規范和鑒定.焊接工藝試驗.第1部分:鋼的弧焊和氣焊以及鎳和鎳合金的弧焊.修改件1 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys; Amendment 1 |
| ISO 15614-1 Technical Corrigendum 1-2005 | 金屬材料焊接過程的規范和鑒定.焊接過程試驗.第1部分:鋼的電弧焊接和氣焊以及鎳和鎳合金的電弧焊接.技術勘 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys; Technical Corrigendum 1 |
| ISO 15614-1-2004 | 金屬材料焊接程序的規范和鑒定.焊接程序試驗.第1部分:鋼的電弧焊和氣焊及鎳和鎳合金的電弧焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| ISO 15614-10-2005 | 金屬材料焊接過程的規范和鑒定.焊接過程試驗.第10部分:高壓干焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 10: Hyperbaric dry welding |
| ISO 15614-11-2002 | 金屬材料焊接程序的規范和鑒定.焊接程序試驗.第11部分:電子和激光束焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 11: Electron and laser beam welding |
| ISO 15614-12-2004 | 金屬材料焊接程序的規范和鑒定.焊接過程試驗.第12部分:點焊、縫焊和凸焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 12: Spot, seam and projection welding |
| ISO 15614-13-2005 | 金屬材料焊接過程的規范和鑒定.焊接過程試驗.第13部分:電阻對接焊和電弧對接焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13: Resistance butt and flash welding |
| ISO 15614-2 Technical Corrigendum 1-2005 | 金屬材料焊接過程的規范和鑒定.焊接過程試驗.第2部分:鋁及其合金的電弧焊接.技術勘誤1 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys; Technical Corrigendum 1 |
| ISO 15614-2 Technical Corrigendum 2-2009 | 金屬材料焊接程序的規范和鑒定.焊接程序試驗.第2部分:鋁及其合金的電弧焊接.修改件2 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys; Amendment 2 |
| ISO 15614-2-2005 | 金屬材料焊接程序的規范和鑒定.焊接過程試驗.第2部分:鋁和鋁合金電弧焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys |
| ISO 15614-3-2008 | 金屬材料的焊接程序規范和合格鑒定.焊接程序試驗.第3部分:非合金和低合金鑄鐵的熔焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 3: Fusion welding of non-alloyed and low-alloyed cast irons |
| ISO 15614-4 Technical Corrigendum 1-2007 | 金屬材料焊接過程的規范和鑒定.焊接過程試驗.第4部分:鋁鑄件的精工焊接.技術勘誤1 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 4: Finishing welding of aluminium castings; Technical Corrigendum 1 |
| ISO 15614-4-2005 | 金屬材料焊接過程的規范和鑒定.焊接過程試驗.第4部分:鋁鑄件的精工焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 4: Finishing welding of aluminium castings |
| ISO 15614-5-2004 | 金屬材料焊接程序的規范和鑒定.焊接程序試驗.第5部分:鈦、鋯及其合金的電弧焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 5: Arc welding of titanium, zirconium and their alloys |
| ISO 15614-6-2006 | 金屬材料焊接程序的規范和鑒定.焊接程序試驗.第6部分:銅及其合金的電弧焊接和氣焊 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 6: Arc and gas welding of copper and its alloys |
| ISO 15614-7-2007 | 金屬材料焊接程序規范和鑒定.焊接程序試驗.第7部分:覆蓋焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 7: Overlay welding |
| ISO 15614-8-2002 | 金屬材料焊接程序的規范和鑒定.焊接程序試驗.第8部分:管對管板接頭焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 8: Welding of tubes to tube-plate joints |
| ISO 15615-2002 | 氣焊設備.焊接、切割和相關工藝用乙炔復式接頭系統.高壓裝置的安全要求 | Gas welding equipment - Acetylene manifold systems for welding, cutting and allied processes - Safety requirements in high-pressure devices |
| ISO 15616-1-2003 | 高質量焊接和切割用CO2激光射線機的驗收試驗.第1部分:通用原理和驗收條件 | Acceptance tests for CO<(Index)2>-laser beam machines for high quality welding and cutting - Part 1: General principles, acceptance conditions |
| ISO 15616-2-2003 | 高質量焊接和切割用CO2激光射線機的驗收試驗.第2部分:靜態和動態準確度的測定 | Acceptance tests for CO<(Index)2>-laser beam machines for high quality welding and cutting - Part 2: Measurement of static and dynamic accuracy |
| ISO 15616-3-2003 | 高質量焊接和切割用CO2激光射線機的驗收試驗.第3部分:氣體流量和壓力測量儀的校正 | Acceptance tests for CO<(Index)2>-laser beam machines for high quality welding and cutting - Part 3: Calibration of instruments for measurement of gas flow and pressure |
| ISO 15616-4-2008 | 高質量焊接和切割用CO2激光光束機的驗收試驗.第4部分:帶二維移動光學的機械 | Acceptance tests for CO-laser beammachines for high quality welding andcutting —Part 4:Machines with 2-D moving optics |
| ISO 15618-1-2001 | 從事水下焊接的焊接員資格檢驗 第1部分：高壓濕焊的潛水焊接員 | Qualification testing of welders for underwater welding - Part 1: Diver-welders for hyperbaric wet welding |
| ISO 15618-2-2001 | 從事水下焊接的焊接員資格檢驗 第2部分：高壓干焊的潛水焊接員和焊接操作員 | Qualification testing of welders for underwater welding - Part 2: Diver-welders and welding operators for hyperbaric dry welding |
| ISO 15620-2000 | 焊接 金屬材料的摩擦焊接 | Welding - Friction welding of metallic materials |
| ISO 15630-2-2002 | 混凝土的鋼筋和預應力用鋼.試驗方法.第2部分:焊接纖維 | Steel for the reinforcement and prestressing of concrete - Test methods - Part 2: Welded fabric |
| ISO 15792-1-2000 | 焊接耗材 試驗方法 第1部分:鋼、鎳和鎳合金全焊金屬試樣的試驗方法 | Welding consumables - Test methods - Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys |
| ISO 15792-2-2000 | 焊接耗材 試驗方法 第2部分:鋼單道焊和雙道焊技術試樣的制備 | Welding consumables - Test methods - Part 2: Preparation of single-run and two-run technique test specimens in steel |
| ISO 15792-3 Technical Corrigendum 1-2006 | 焊接耗材.試驗方法.第3部分:角焊中焊接耗材的根角熔深和填位能力的分類試驗 | Welding consumables - Test methods - Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld; Technical Corrigendum 1 |
| ISO 15792-3-2000 | 焊接耗材 試驗方法 第3部分:角焊中焊接消耗品的根角熔深和填位能力的分類試驗 | Welding consumables - Test methods - Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld |
| ISO 16834-2006 | 焊接消耗品.高強度鋼的氣體保護電弧焊用焊絲電極、焊絲、焊條和沉積金屬.分類 | Welding consumables - Wire electrodes, wires, rods and deposits for gas-shielded arc welding of high strength steels - Classification |
| ISO 17632-2004 | 焊接消耗品.非合金鋼及細粒鋼氣體保護的和非氣體保護金屬弧焊用藥芯電極.分類 | Welding consumables - Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels - Classification |
| ISO 17633-2004 | 焊接消耗品.不銹鋼和耐熱鋼的氣體保護和非氣體保護金屬弧焊用藥芯電極和焊條.分類 | Welding consumables - Tubular cored electrodes and rods for gas shielded and non-gas shielded metal arc welding of stainless and heat-resisting steels - Classification |
| ISO 17634-2004 | 焊接消耗品.耐蠕變鋼的氣體保護金屬電弧焊用管狀有芯焊條.分類 | Welding consumables - Tubular cored electrodes for gas shielded metal arc welding of creep-resisting steels - Classification |
| ISO 17636-2003 | 焊縫的無損檢驗.熔焊接頭的放射檢驗 | Non-destructive testing of welds - Radiographic testing of fusion-welded joints |
| ISO 17637-2003 | 焊縫的無損檢驗.熔焊接頭的外觀檢驗 | Non-destructive testing of welds - Visual testing of fusion-welded joints |
| ISO 17640-2005 | 焊接的無損檢驗.焊接接頭的超聲波檢驗 | Non-destructive testing of welds - Ultrasonic testing of welded joints |
| ISO 17641-1-2004 | 金屬材料焊接的有損試驗.焊接的熱裂試驗.弧焊工藝.第1部分:總則 | Destructive tests on welds in metallic materials - Hot cracking tests for weldments - Arc welding processes - Part 1: General |
| ISO 17641-2-2005 | 金屬材料焊接的有損試驗.焊接的熱裂試驗.弧焊工藝.第2部分:自束試驗 | Destructive tests on welds in metallic materials - Hot cracking tests for weldments - Arc welding processes - Part 2: Self-restraint tests |
| ISO 17642-1-2004 | 金屬材料焊接的有損試驗.焊接的冷裂試驗.弧焊工藝.第1部分:總則 | Destructive tests on welds in metallic materials - Cold cracking tests for weldments - Arc welding processes - Part 1: General |
| ISO 17642-2-2005 | 金屬材料焊接的有損試驗.焊接的冷裂試驗.弧焊工藝.第2部分:自束試驗 | Destructive tests on welds in metallic materials - Cold cracking tests for weldments - Arc welding processes - Part 2: Self-restraint tests |
| ISO 17642-3-2005 | 金屬材料焊接的有損試驗.焊接的冷裂試驗.弧焊工藝.第3部分:外部載荷試驗 | Destructive tests on welds in metallic materials - Cold cracking tests for weldments - Arc welding processes - Part 3: Externally loaded tests |
| ISO 17643-2005 | 焊接的無損檢驗.用矢量分析的焊接渦流檢驗 | Non-destructive testing of welds - Eddy current testing of welds by complex-plane analysis |
| ISO 17652-1-2003 | 焊接.與焊接和相關工藝有關的工廠底漆的試驗.第1部分:一般要求 | Welding - Test for shop primers in relation to welding and allied processes - Part 1: General requirements |
| ISO 17652-2-2003 | 焊接.與焊接和相關工藝有關的工廠底漆的試驗.第2部分:工廠底漆的焊接特性 | Welding - Test for shop primers in relation to welding and allied processes - Part 2: Welding properties of shop primers |
| ISO 17652-3-2003 | 焊接.與焊接和相關工藝有關的工廠底漆的試驗.第3部分:熱切割 | Welding - Test for shop primers in relation to welding and allied processes - Part 3: Thermal cutting |
| ISO 17652-4-2003 | 焊接.與焊接和相關工藝有關的工廠底漆的試驗.第4部分:煙氣排放 | Welding - Test for shop primers in relation to welding and allied processes - Part 4: Emission of fumes and gases |
| ISO 17654-2003 | 金屬材料焊接的破壞檢驗.電阻焊接.電阻縫焊的壓力試驗 | Destructive tests on welds in metallic materials - Resistance welding - Pressure test on resistance seam welds |
| ISO 17655-2003 | 金屬材料焊接的有損試驗.測量δ鐵素體用的取樣方法 | Destructive tests on welds in metallic materials - Method for taking samples for delta ferrite measurement |
| ISO 17657-1-2005 | 電阻焊.電阻焊用焊接電流測量.第1部分:測量指南 | Resistance welding - Welding current measurement for resistance welding - Part 1: Guidelines for measurement |
| ISO 17657-2-2005 | 電阻焊.電阻焊用焊接電流測量.第2部分:電流感應線圈式焊接電流計 | Resistance welding - Welding current measurement for resistance welding - Part 2: Welding current meter with current sensing coil |
| ISO 17657-3-2005 | 電阻焊.電阻焊用焊接電流測量.第3部分:電流感應線圈 | Resistance welding - Welding current measurement for resistance welding - Part 3: Current sensing coil |
| ISO 17657-4-2005 | 電阻焊.電阻焊用焊接電流測量.第4部分:校驗系統 | Resistance welding - Welding current measurement for resistance welding - Part 4: Calibration system |
| ISO 17657-5-2005 | 電阻焊.電阻焊用焊接電流測量.第5部分:焊接電流測量系統的驗證 | Resistance welding - Welding current measurement for resistance welding - Part 5: Verification of welding current measuring system |
| ISO 17658-2002 | 焊接.氧氣火焰切割、激光束切割和等離子體切割的缺陷 | Welding - Imperfections in oxyfuel flame cuts, laser beam cuts and plasma cuts - Terminology |
| ISO 17659-2002 | 焊接.圖示焊接接頭的多語種術語 | Welding - Multilingual terms for welded joints with illustrations |
| ISO 17660-1-2006 | 焊接.鋼筋焊接.第1部分:承載焊接接縫 | Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints |
| ISO 17660-2-2006 | 焊接.鋼筋焊接.第2部分:非承載焊接接縫 | Welding - Welding of reinforcing steel - Part 2: Non load-bearing welded joints |
| ISO 17662-2005 | 焊接.焊接用設備的校正、驗證和確認(包括輔助活動) | Welding - Calibration, verification and validation of equipment used for welding, including ancillary activities |
| ISO 17663-2009 | 焊接.焊接及相關工藝的熱處理質量要求 | Welding - Quality requirements for heat treatment in connection with welding and allied processes |
| ISO 17846-2004 | 焊接及相關工藝.健康和安全.電弧焊接和切割用設備和消耗品的無字預警標簽 | Welding and allied processes - Health and safety - Wordless precautionary labels for equipment and consumables used in arc welding and cutting |
| ISO 18172-1-2007 | 儲氣瓶.可再灌裝的焊接不銹鋼氣瓶.第1部分:試驗壓力≤6MPa | Gas cylinders - Refillable welded stainless steel cylinders - Part 1: Test pressure 6 MPa and below |
| ISO 18172-2-2007 | 儲氣瓶.可再灌裝的焊接不銹鋼氣瓶.第2部分:試驗壓力大于6MPa | Gas cylinders - Refillable welded stainless steel cylinders - Part 2: Test pressure greater than 6 MPa |
| ISO 18207-2006 | 道路車輛.3.5噸拖車.控制疲勞試驗后聯軸球焊接牽引支架 | Road vehicles - Trailers up to 3,5 t - Control of welded towing brackets for coupling ball after fatigue testing |
| ISO 18273-2004 | 焊接消耗品.鋁和鋁合金焊接用焊絲電極、金屬絲和棒材.分類 | Welding consumables - Wire electrodes, wires and rods for welding of aluminium and aluminium alloys - Classification |
| ISO 18274 Technical Corrigendum 1-2005 | 焊接消耗品.鎳和鎳合金熔焊用焊絲和條式電極、焊線和焊條.分類.技術勘誤1 | Welding consumables - Wire and strip electrodes, wires and rods for fusion welding of nickel and nickel alloys - Classification; Technical Corrigendum 1 |
| ISO 18274 Technical Corrigendum 2-2006 | 焊接耗材.鎳及鎳合金熔焊用絲狀和帶狀電極、焊絲和焊條.分類.技術勘誤2 | Welding consumables - Wire and strip electrodes, wires and rods for fusion welding of nickel and nickel alloys - Classification; Technical Corrigendum 2 |
| ISO 18274-2004 | 焊接消耗品.鎳和鎳合金電弧焊用焊絲和條式電極、金屬線和棒材.分類 | Welding consumables - Wire and strip electrodes, wires and rods for arc welding of nickel and nickel alloys - Classification |
| ISO 18275 Technical Corrigendum 1-2007 | 焊接耗材.高強度鋼的手工金屬電弧焊用涂覆電焊條.分類.技術勘誤1 | Welding consumables - Covered electrodes for manual metal arc welding of high-strength steels - Classification; Technical Corrigendum 1 |
| ISO 18275-2005 | 焊接消耗品.高強度鋼的手工金屬極電弧焊用涂覆電焊條.分類 | Welding consumables - Covered electrodes for manual metal arc welding of high-strength steels - Classification |
| ISO 18276-2005 | 焊接消耗品.高強度鋼的氣體保護和非氣體保護金屬極電弧焊用藥芯電極.分類 | Welding consumables - Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high-strength steels - Classification |
| ISO 18279-2003 | 釬焊.釬焊接頭的缺陷 | Brazing - Imperfections in brazed joints |
| ISO 18592-2009 | 電阻焊接.焊點破壞性試驗.多點焊接樣品的疲勞試驗方法 | Resistance welding - Destructive testing of welds - Method for the fatigue testing of multi-spot-welded specimens |
| ISO 18594-2007 | 電阻點焊接、電阻凸焊和電阻縫隙焊接.測定鋁和鋼材料的躍遷電阻 | Resistance spot-, projection- and seam-welding - Method for determining the transition resistance on aluminium and steel material |
| ISO 18595-2007 | 電阻焊接.鋁和鋁合金的點焊.可焊接性、焊接和測試 | Resistance welding - Spot welding of aluminium and aluminium alloys - Weldability, welding and testing |
| ISO 2016-1981 | 銅管用毛細管焊接接頭 組裝尺寸和試驗方法 | Capillary solder fittings for copper tubes; Assembly dimensions and tests |
| ISO 20703-2006 | 氣瓶.可再充裝的焊接鋁合金氣瓶.設計、結構和試驗 | Gas cylinders - Refillable welded aluminium-alloy cylinders - Design, construction and testing |
| ISO 21670-2003 | 帶法蘭的六角焊接螺母 | Hexagon weld nuts with flange |
| ISO 21952-2007 | 焊接消耗品.抗蠕變鋼的氣體保護電弧焊用絲狀電極、焊絲、焊條和沉漬物. 分類 | Welding consumables - Wire electrodes, wires, rods and deposits for gas-shielded arc welding of creep-resisting steels - Classification |
| ISO 22826-2005 | 金屬材料焊縫的破壞性試驗.激光和電子束焊接窄接頭的硬度試驗(維氏和努氏硬度試驗) | Destructive tests on welds in metallic materials - Hardness testing of narrow joints welded by laser and electron beam (Vickers and Knoop hardness tests) |
| ISO 22827-1-2005 | Nd:YAG激光射線焊接機器的加速試驗.帶光纖傳送的機器.第1部分:激光裝配 | Acceptance tests for Nd:YAG laser beam welding machines - Machines with optical fibre delivery - Part 1: Laser assembly |
| ISO 22827-2-2005 | Nd:YAG激光射線焊接機器的加速試驗.帶光纖傳送的機器.第2部分:移動裝置 | Acceptance tests for Nd:YAG laser beam welding machines - Machines with optical fibre delivery - Part 2: Moving mechanism |
| ISO 22829-2007 | 電阻焊接.帶組合變壓器焊接槍用變壓器整流器.1000 Hz頻率工作變壓器整流器 | Resistance welding - Transformer-rectifier for welding guns with integrated transformers - Transformer-rectifier units operating at 1000 Hz frequency |
| ISO 22991-2004 | 儲氣瓶.液化石油氣用可運輸?shù)目稍偬畛浜附愉撈?設計和建造 | Gas cylinders - Transportable refillable welded steel cylinders for liquefied petroleum gas (LPG) - Design and construction |
| ISO 23278-2006 | 焊接無損測試.焊接的磁性顆粒測試.驗收水平 | Non-destructive testing of welds - Magnetic particle testing of welds - Acceptance levels |
| ISO 24034 AMD 1-2008 | 焊接消耗品.鈦和鈦合金的熔焊用實心焊絲和焊條.分類.修改件1 | Welding consumables - Solid wires and rods for fusion welding of titanium and titanium alloys - Classification; Amendment 1 |
| ISO 24034-2005 | 焊接耗材.鈦和鈦合金的熔焊用焊絲和焊條.分類 | Welding consumables - Solid wires and rods for fusion welding of titanium and titanium alloys - Classification |
| ISO 242-1975 | 硬質合金焊接車刀片 | Carbide tips for brazing on turning tools |
| ISO 24373-2008 | 焊接消耗品.銅和銅合金的熔焊用固體焊絲和焊桿.分類 | Welding consumables - Solid wires and rods for fusion welding of copper and copper alloys - Classification |
| ISO 24394-2008 | 航空航天設施焊接.焊接工和焊接操作工用鑒定試驗.金屬部件的熔焊 | Welding for aerospace applications - Qualification test for welders and welding operators - Fusion welding of metallic components |
| ISO 24497-3-2007 | 無損檢驗.金屬存儲器.第3部分:焊接接口檢驗 | Non-destructive testing - Metal magnetic memory - Part 3: Inspection of welded joints |
| ISO 24598-2007 | 焊接耗材.抗蠕變鋼的潛弧焊用實心焊絲、管狀芯焊條和焊條/焊劑組合制品.分類 | Welding consumables - Solid wire electrodes, tubular cored electrodes and electrode/flux combinations for submerged arc welding of creep-resisting steels - Classification |
| ISO 2503-2009 | 氣焊設備.用于壓力在300 bar(30兆帕)以下的焊接,切割及相關工藝的調壓器和配備氣瓶用流量計量裝置的調壓器 | Gas welding equipment - Pressure regulators and pressure regulators with flow-metering devices for gas cylinders used in welding, cutting and allied processes up to 300 bar (30 MPa) |
| ISO 2553-1992 | 焊接、硬釬焊和軟釬焊接頭 圖樣上的符號表示法 | Welded, brazed and soldered joints; symbolic representation on drawings |
| ISO 2560-2009 | 焊接材料.非合金鋼和細晶粒鋼的手工金屬電弧焊用涂敷焊條.分類 | Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification |
| ISO 26304 Technical Corrigendum 1-2009 | 焊接消耗品.高強度鋼潛弧焊接用實心焊條、管芯焊條和焊條熔接組合件.分類.技術勘誤1 | Welding consumables - Solid wire electrodes, tubular cored electrodes and electrode-flux combinations for submerged arc welding of high strength steels - Classification; Technical Corrigendum 1 |
| ISO 26304-2008 | 焊接消耗品.高強度鋼的潛弧焊用實心焊條、管狀芯焊條和焊條-焊劑熔接物.分類 | Welding consumables - Solid wire electrodes, tubular cored electrodes and electrode-flux combinations for submerged arc welding of high strength steels - Classification |
| ISO 28319-2010 | 牙科.激光焊接 | Dentistry - Laser welding |
| ISO 3253-1998 | 氣焊設備 焊接、切割和有關工藝設備的軟管接頭 | Gas welding equipment - Hose connections for equipment for welding, cutting and allied processes |
| ISO 3305-1985 | 光端焊接精密鋼管 交貨技術條件 | Plain end welded precision steel tubes; Technical conditions for delivery |
| ISO 3580-2010 | 焊接消耗品.抗蠕變鋼手工電弧焊接用涂敷焊條.分類 | Welding consumables - Covered electrodes for manual metal arc welding of creep-resisting steels - Classification |
| ISO 3581 Technical Corrigendum 1-2008 | 焊接消耗品.不銹鋼和耐熱鋼的手工金屬電弧焊接用涂劑焊條.分類.技術勘誤1 | Welding consumables - Covered electrodes for manual metal arc welding of stainless and heat-resisting steels - Classification; Technical Corrigendum 1 |
| ISO 3581-2003 | 焊料.不銹鋼和耐熱鋼的手工金屬電弧焊接用涂劑焊條.分類 | Welding consumables - Covered electrodes for manual metal arc welding of stainless and heat-resisting steels - Classification |
| ISO 3677-1992 | 軟釬焊、硬釬焊和釬接焊接用填充金屬 符號規定 | Filler metal for soft soldering, brazing and braze welding; designation |
| ISO 3690-2000 | 焊接 碳鋼和低合金鋼手工焊熔敷金屬擴散氫的測定 | Welding and allied processes - Determination of hydrogen content in ferritic steel arc weld metal |
| ISO 3821-2008 | 氣焊設備.焊接,切割和相關工藝用橡膠軟管 | Gas welding equipment - Rubber hoses for welding, cutting and allied processes |
| ISO 3913 ADD 1-1980 | 造船 鋼質焊接帶纜樁 補充1:內河航行用雙纜樁 | Shipbuilding; welded steel bollards; addendum 1 |
| ISO 3913-1977 | 造船 鋼質焊接帶纜樁 | Shipbuilding; Welded steel bollards |
| ISO 4019-2001 | 結構鋼 冷成型、焊接、結構中空截面 尺寸和截面特性 | Structural steels - Cold-formed, welded, structural hollow sections - Dimensions and sectional properties |
| ISO 4063-2009 | 焊接及相關工藝過程.工藝過程名稱和參考號 | Welding and allied processes - Nomenclature of processes and reference numbers |
| ISO 4136-2001 | 金屬材料焊接的破壞性試驗 橫向拉申試驗 | Destructive tests of welds in metallic materials - Traverse tensile test |
| ISO 4200-1991 | 光端焊接和無縫鋼管 管的尺寸和單位長度重量的一覽表 | Plain end steel tubes, welded and seamless; general tables of dimensions and masses per unit length |
| ISO 4706-1-2008 | 氣瓶.可重復充裝的鋼制焊接氣瓶.第1部分:試驗壓力≤60bar | Gas cylinders - Refillable welded steel cylinders - Part 1: Test pressure 60 bar and below |
| ISO 4706-2008 | 氣瓶.可再填充焊接鋼瓶.第1部分:試驗壓力小于等于60ba | Gas cylinders - Refillable welded steel cylinders - Part 1: Test pressure 60 bar and below |
| ISO 4778-1981 | 焊接吊鏈 M(4)、S(6)和T(8)級 | Chain slings of welded construction; Grades M (4), S (6) and T (8) |
| ISO 4850-1979 | 焊接和相關工藝的專用護目鏡、濾光鏡 應用和透射率的要求 | Personal eye-protectors for welding and related techniques; Filters; Utilisation and transmittance requirements |
| ISO 4978-1983 | 焊接氣瓶用軋制扁鋼制品 | Flat rolled steel products for welded gas cylinders |
| ISO 5171-2009 | 氣體焊接設備.焊接,切割和相關工藝過程中使用的壓力儀表 | Gas welding equipment - Pressure gauges used in welding, cutting and allied processes |
| ISO 5178-2001 | 金屬材料焊接的破壞性試驗 熔焊接頭的焊接金屬的縱向拉申試驗 | Destructive tests on welds in metallic materials - Longitudinal tensile test on weld metal in fusion welded joints |
| ISO 5182-2008 | 電阻焊接.電極和輔助設備用材料 | Resistance welding - Materials for electrodes and ancillary equipment |
| ISO 5187-1985 | 焊接和相關工藝 用軟釬焊和硬釬焊接頭 力學試驗方法 | Welding and allied processes; Assemblies made with soft solders and brazing filler metals; Mechanical test methods |
| ISO 544-2003 | 焊接消耗品.焊接填充料的技術交貨條件.產品類型、尺寸、公差和標記 | Welding consumables - Technical delivery conditions for welding filler materials - Type of product, dimensions, tolerances and markings |
| ISO 5625-1978 | 造船 鋼管管路法蘭焊接通艙管 PN6、PN10和PN16 | Shipbuilding; Welded bulkhead pieces with flanges for steel pipework; PN 6, PN 10 and PN 16 |
| ISO 5817 Technical Corrigendum 1-2006 | 焊接.鋼、鎳、鈦及其合金的熔焊接縫(束焊除外).缺陷的質量等級.技術勘誤1 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections; Technical Corrigendum 1 |
| ISO 5817-2003 | 焊接.鋼、鎳、鈦及其合金熔焊接頭(束焊除外).缺陷的質量分級 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections |
| ISO 5821-2009 | 電阻焊接.點焊電極帽接頭 | Resistance welding - Spot welding electrode caps |
| ISO 636-2004 | 焊接消耗品.非合金鋼和細粒鋼的鎢惰性氣體焊用焊條、焊絲和溶敷金屬.分類 | Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification |
| ISO 6520-1-2007 | 焊接和相關工藝.金屬材料中幾何缺陷的分類.第1部分:熔焊 | Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 1: Fusion welding |
| ISO 6520-2-2001 | 焊接及相關工藝 金屬材料的幾何缺陷的分類 第2部分：壓焊 | Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 2: Welding with pressure |
| ISO 669-2000 | 電阻焊接 電阻焊設備 機械和電要求 | Resistance welding - Resistance welding equipment - Mechanical and electrical requirements |
| ISO 6758-1980 | 熱交換器用焊接鋼管 | Welded steel tubes for heat exchangers |
| ISO 6761-1981 | 鋼管 焊接用管端和配件的預處理 | Steel tubes; Preparation of ends of tubes and fittings for welding |
| ISO 6847-2000 | 焊接耗材 化學分析用焊接金屬的熔敷 | Welding consumables - Deposition of a weld metal pad for chemical analysis |
| ISO 6935-3 Technical Corrigendum 1-2000 | 鋼筋混凝土用鋼 第3部分:焊接鋼筋網 技術勘誤1 | Steel for the reinforcement of concrete - Part 3: Welded fabric; Technical Corrigendum 1 |
| ISO 6935-3-1992 | 鋼筋混凝土用鋼 第3部分:焊接鋼筋網 | Steel for the reinforcement of concrete; part 3: welded fabric |
| ISO 6947-1990 | 焊接 工作位置 傾角和轉角的定義(ISO 6947-1980的修訂本) | Welds; working positions; definitions of angles of slope and rotation (revision of ISO 6947:1980) |
| ISO 6971-2002 | 焊接結構拉曳用彎板鏈、附件和鏈輪 | Cranked-link drag chains of welded construction, attachments and sprockets |
| ISO 6972-2002 | 焊接結構工程用彎板鏈、附件和鏈輪 | Cranked-link mill chains of welded construction, attachments and sprockets |
| ISO 7286-1986 | 電阻焊接設備的圖形符號 兩種語言版 | Graphical symbols for resistance welding equipment Bilingual edition |
| ISO 7289-2010 | 氣焊設備.焊接、切割及相關工藝用帶關閉閥的快速接頭 | Gas welding equipment - Quick-action couplings with shut-off valves for welding, cutting and allied processes |
| ISO 7291-1999 | 氣焊設備 用于300 bar以下的焊接、切割及相關工藝用匯流系統上的壓力調節器 | Gas welding equipment - Pressure regulators for manifold systems used in welding, cutting and allied processes up to 300 bar |
| ISO 7593-1986 | 非焊接吊鏈 T(8)級 | Chain slings assembled by methods other than welding; Grade T(8) |
| ISO 8205-1-2002 | 電阻焊接水冷次級線圈連接電纜.第1部分:雙導體連接電纜的尺寸和要求 | Water-cooled secondary connection cables for resistance welding - Part 1: Dimensions and requirements for double-conductor connection cables |
| ISO 8205-2-2002 | 電阻焊接水冷次級線圈連接電纜.第2部分:單根導線連接電纜的尺寸和要求 | Water-cooled secondary connection cables for resistance welding - Part 2: Dimensions and requirements for single-conductor connection cables |
| ISO 8205-3-1993 | 電阻焊接水冷次級線圈連接電纜 第3部分:試驗要求 | Water-cooled secondary connection cables for resistance welding; part 3: test requirements |
| ISO 8207-1996 | 氣焊設備 焊接、切割和相關工藝設備用軟管組件規范 | Gas welding equipment - Specification for hose assemblies for equipment for welding, cutting and allied processes |
| ISO 8249-2000 | 焊接 奧氏體和成雙鐵素體奧氏體鎳-鉻(Cr-Ni)不銹鋼焊接金屬中鐵素體數(FN)的測定 | Welding - Determination of Ferrite Number (FN) in austenitic and duplex ferritic-austenitic Cr-Ni stainless steel weld metals |
| ISO 8501-3-2006 | 涂裝油漆和有關產品前鋼材的預處理.表面清潔度的目視評定.第3部分:焊接、切邊及其它表面缺陷區域的處理等級 | Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 3: Preparation grades of welds, edges and other areas with surface imperfections |
| ISO 857-1-1998 | 焊接和相關工藝 術語 第1部分:金屬焊接工藝 兩種語言版 | Welding and allied processes - Vocabulary - Part 1: Metal welding processes |
| ISO 857-2-2005 | 焊接和相關工藝.詞匯.第2部分:軟釬焊和銅焊工藝及相關術語 | Welding and allied processes - Vocabulary - Part 2: Soldering and brazing processes and related terms |
| ISO 9015-1-2001 | 金屬材料焊接的破壞性試驗 硬度試驗 第1部分：弧焊接頭的硬度試驗 | Destructive tests on welds in metallic materials - Hardness testing - Part 1: Hardness test on arc welded joints |
| ISO 9015-2-2003 | 金屬材料焊接的破壞性試驗.硬度試驗.第2部分:焊接件的顯微硬度試驗 | Destructive tests on welds in metallic materials - Hardness testing - Part 2: Microhardness testing of welded joints |
| ISO 9016-2001 | 金屬材料焊接的破壞性試驗 碰撞試驗 試驗樣品的位置、切口的朝向和檢查 | Destructive tests on welds in metallic materials - Impact tests - Test specimen location, notch orientation and examination |
| ISO 9017-2001 | 金屬材料焊接的破壞性試驗 斷裂試驗 | Destructive tests on welds in metallic materials - Fracture test |
| ISO 9018-2003 | 金屬材料焊接的破壞性試驗.十字形接縫和搭接縫的抗拉試驗 | Destructive tests on welds in metallic materials - Tensile test on cruciform and lapped joints |
| ISO 9302-1994 | 壓力用途的無縫鋼管和焊接(埋弧焊除外)鋼管 液壓密封驗證電磁試驗法 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; electromagnetic testing for verification of hydraulic leak-tightness |
| ISO 9303-1989 | 壓力用途的無縫鋼管和焊接(埋弧焊除外)鋼管 檢測縱向缺陷用全周邊超聲波試驗 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; full peripheral ultrasonic testing for the detection of longitudinal imperfections |
| ISO 9304-1989 | 壓力用途的無縫鋼管和焊接(埋弧焊除外)鋼管 檢測缺陷用渦流電流試驗 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; eddy current testing for the detection of imperfections |
| ISO 9327-4-1999 | 壓力用途的鋼鍛件和軋制或鍛造的棒材 交貨技術條件 第4部分:高強度可焊接細粒鋼 | Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions - Part 4: Weldable fine grain steels with high proof strength |
| ISO 9328-6-2004 | 壓力用途扁鋼產品.交貨技術條件.第6部分:淬火和回火的可焊接細粒鋼 | Steel flat products for pressure purposes - Technical delivery conditions - Part 6: Weldable fine grain steels, quenched and tempered |
| ISO 9330-1-1990 | 壓力用途的焊接鋼管 交貨技術條件 第1部分:規定室溫性能的非合金鋼管 | Welded steel tubes for pressure purposes; technical delivery conditions; part 1: unalloyed steel tubes with specified room temperatures properties |
| ISO 9330-2-1997 | 壓力用途的焊接鋼管 交貨技術條件 第2部分:規定高溫性能的電阻焊接和感應焊接非合金鋼管和合金鋼管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 2: Electric resistance and induction welded unalloyed and alloyed steel tubes with specified elevated temperature properties |
| ISO 9330-3-1997 | 壓力用途的焊接鋼管 交貨技術條件 第3部分:規定低溫性能的電阻焊接和感應焊接非合金鋼管和合金鋼管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 3: Electric resistance and induction welded unalloyed and alloyed steel tubes with specified low temperature properties |
| ISO 9330-4-2000 | 壓力用途的焊接鋼管 交貨技術條件 第4部分:規定高溫性能的埋弧焊接非合金鋼管和合金鋼管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 4: Submerged arc-welded unalloyed and alloyed steel tubes with specified elevated temperature properties |
| ISO 9330-5-2000 | 壓力用途的焊接鋼管 交貨技術條件 第5部分:規定低溫性能的埋弧焊接非合金鋼管和合金鋼管 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 5: Submerged arc-welded unalloyed and alloyed steel tubes with specified low temperature properties |
| ISO 9330-6-1997 | 壓力用途的焊接鋼管 交貨技術條件 第6部分:奧氏體不銹鋼管的焊接長度 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 6: Longitudinally welded austenitic stainless steel tubes |
| ISO 9402-1989 | 壓力用途的無縫鋼管和焊接(埋弧焊除外)鋼管 檢測縱向缺陷用鐵磁鋼管全周邊磁轉換/磁鏈試驗 | Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes; full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of longitudinal imperfections |
| ISO 9539-2010 | 氣焊設備.用于氣體焊接、切割和相關工藝過程設備的材料 | Gas welding equipment - Materials for equipment used in gas welding, cutting and allied processes |
| ISO 9692-1-2003 | 焊接和相關工藝.關于接縫準備的建議.第1部分:鋼的手動金屬電弧焊接、氣體保護金屬電弧焊、氣焊、TIG焊接和 | Welding and allied processes - Recommendations for joint preparation - Part 1: Manual metal-arc welding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels |
| ISO 9692-2-1998 | 焊接和相關工藝 接頭的制備 第2部分:鋼的埋弧焊 | Welding and allied processes - Joint preparation - Part 2: Submerged arc welding of steels |
| ISO 9692-3-2000 | 焊接和相關工藝 接頭制備的建議 第3部分:鋁及鋁合金的金屬焊條惰性氣體保護焊和鎢焊條惰性氣體保護焊 | Welding and allied processes - Recommendations for joint preparation - Part 3: Metal inert gas welding and tungsten inert gas welding of aluminium and its alloys |
| ISO 9692-4-2003 | 焊接和相關工藝.接頭制備的建議.第4部分:包鋼 | Welding and allied processes - Recommendations for joint preparation - Part 4: Clad steels |
| ISO/TR 13393-2009 | 焊接消耗品.硬表面堆焊.微觀結構 | Welding consumables - Hardfacing classification - Microstructures |
| ISO/TR 15608-2005 | 焊接.金屬材料分類體系指南 | Welding - Guidelines for a metallic materials grouping system |
| ISO/TR 17641-3-2005 | 金屬材料焊接的有損試驗.焊接的熱裂試驗.弧焊工藝.第3部分:外部負載試驗 | Destructive tests on welds in metallic materials - Hot cracking tests for weldments - Arc welding processes - Part 3: Externally loaded tests |
| ISO/TR 17671-1-2002 | 焊接.金屬材料焊接的推薦.第1部分:電弧焊接通用指南 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| ISO/TR 17671-2-2002 | 焊接.金屬材料焊接的推薦.第2部分:鐵素體鋼的電弧焊接 | Welding - Recommendations for welding of metallic materials - Part 2: Arc welding of ferritic steels |
| ISO/TR 17671-3-2002 | 焊接.金屬材料焊接的推薦.第3部分:不銹鋼的電弧焊接 | Welding - Recommendations for welding of metallic materials - Part 3: Arc welding of stainless steels |
| ISO/TR 17671-4-2002 | 焊接.金屬材料焊接的推薦.第4部分:鋁和鋁合金的電弧焊接 | Welding - Recommendations for welding of metallic materials - Part 4: Arc welding of aluminium and aluminium alloys |
| ISO/TR 17671-5-2004 | 焊接.金屬材料焊接的推薦.第5部分:覆層鋼的焊接 | Welding - Recommendations for welding of metallic materials - Part 5: Welding of clad steels |
| ISO/TR 17671-6-2005 | 焊接.金屬材料焊接建議.第6部分:激光束焊接 | Welding - Recommendations for welding of metallic materials - Part 6: Laser beam welding |
| ISO/TR 17671-7-2004 | 焊接.金屬材料焊接的推薦.第7部分:電子束焊接 | Welding - Recommendations for welding of metallic materials - Part 7: Electron beam welding |
| ISO/TR 17844-2004 | 焊接.避免冷裂的標準化方法的比較 | Welding - Comparison of standardised methods for the avoidance of cold cracks |
| ISO/TR 20172-2009 | 焊接材料分組系統.歐洲材料 | Welding - Grouping systems for materials - European materials |
| ISO/TR 20173-2009 | 焊接.材料分組系統.美國材料 | Welding - Grouping systems for materials - American materials |
| ISO/TR 20174-2005 | 焊接.材料分組系統.日本材料 | Welding - Grouping systems for materials - Japanese materials |
| ISO/TR 22824-2003 | 焊接消耗品.規范中預測的和實測的FN.IIW委員會IX專家的見解 | Welding consumbales - Predicted and measured FN in specifications - A position statement of the experts of IIW Commission IX |
| ISO/TR 25901-2007 | 焊接和相關工藝.詞匯 | Welding and related processes - Vocabulary |
| ISO/TR 8610-1984 | 薄壁金屬容器 用于乳類及乳制品的兩端經焊接的抽氣圓罐 容量和相應直徑 | Light gauge metal containers; Round vent-hole cans with soldered ends for milk and milk products; Capacities and related diameters |
| ISO/TS 15011-5-2006 | 焊接和相關工藝的衛生和安全.煙塵和氣體取樣的實驗室法.第5部分:完全或部分有機材料組成的產品在焊接或切割 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 5: Identification of thermal-degradation products generated when welding or cutting through products composed wholly or partly of organic materials |
| ISO/TS 17845-2004 | 焊接及相關工藝.缺陷的名稱與符號系統 | Welding and allied processes - Designation system for imperfections |
| 編號 | 中文名稱 | 英文名稱 |