| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| BB/T 0025-2004 | 聚三氟氯乙烯塑料襯里截止閥 | () |
| BB/T 0043-2007 | 塑料物流周轉箱 | () |
| BB/T 0044-2007 | 包裝容器 塑料農藥瓶 | () |
| CP 312-1-1973 | 塑料管道(熱塑材料)實用規程.第1部分:一般原理和材料選擇 | Code of practice for plastics pipework (thermoplastics material). General principles and choice of material |
| CP 312-2-1973 | 塑料管道(熱塑材料)實用規程.第2部分:壓力液體輸送用非增塑PVC管 | Code of practice for plastics pipework (thermoplastics material). Unplasticized PVC pipework for the conveyance of liquids under pressure |
| DD ENV 1401-2-2001 | 非壓力地下廢水排放和污水系統的塑料管道系統.非增塑聚氯乙烯.符合性評定指南 | Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinylchloride) (PVC-U). Guidance for assessment of conformity |
| DD ENV 1452-6-2002 | 供水用塑料管道系統.未增塑聚氯乙烯(PVC-U).安裝指南 | Plastics piping systems for water supply. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for installation |
| DL/T 622-1997(2005) | 立式水輪發電機彈性金屬塑料推力軸瓦技術條件 | () |
| DL/T 742-2001 | 冷卻塔塑料部件技術條件 | () |
| DL/T 802.2-2007 | 電力電纜用導管技術條件 第2部分：玻璃纖維增強塑料電纜導管 | Technical requirements for electric cable conduits Part 2:Cable conduits of fiberglass reinforced plastics |
| DL/T 802.3-2007 | 電力電纜用導管技術條件 第3部分：氯化聚氯乙烯及硬聚氯乙烯塑料電纜導管 | Technical requirements for electric cable conduits Part 3:Cable conduits of chlorinated polyvinyl chloride and unplasticized polyvinyl chloride |
| DL/T 802.4-2007 | 電力電纜用導管技術條件 第4部分：氯化聚氯乙烯及硬聚氯乙烯塑料雙壁波紋電纜導管 | Technical requirements for electric cable conduits Part 4:Double wall corrugated cable conduits of chlorinated polyvinyl chloride and unplasticized polyvinyl chloride |
| FZ 93004-1991 | 紡紗和捻線用塑料鉤 | () |
| FZ 93010-1991 | 換梭式梭子用塑料緯紗管 | () |
| FZ/T 90003.1-1991 | 塑料經紗管和緯紗管試驗方法靜彎曲 | () |
| FZ/T 90003.2-1991 | 塑料經紗管和緯紗管試驗方法沖擊功 | () |
| FZ/T 90003.3-1991 | 塑料經紗管和緯紗管試驗方法振幅 | () |
| FZ/T 90080.1-1995 | 紡織用塑料投梭結試驗方法 球壓痕硬度 | () |
| FZ/T 90080.2-1995 | 織機用塑料投梭結試驗方法 沖擊強度 | () |
| FZ/T 92044-1995 | 酚醛塑料槽筒 | () |
| FZ/T 93004-2002(2009) | 紡紗和捻線用塑料鉤 | () |
| FZ/T 93008-2002(2009) | 環錠細沙機用塑料經紗管 | () |
| FZ/T 93010-2002(2009) | 換梭式梭子用塑料緯紗管 | () |
| FZ/T 93029-1994 | 塑料粗紗管 | () |
| FZ/T 94017-1994 | 長絲絡并捻用塑料雙邊筒管 | () |
| FZ/T 94030-1995 | 棉織機用塑料投梭結 | () |
| FZ/T 94031-1995 | 毛織機用塑料投梭結 | () |
| FZ/T 94032-1995 | 麻織機用塑料投梭結 | () |
| FZ/T 94033-1995 | 多梭箱絲織機用塑料投梭結 | () |
| FZ/T 96014-1993 | 簾子線捻線用塑料雙邊筒管 | () |
| GB 10457-2009 | 食品用塑料自粘保鮮膜 | Plastic cling wrap film for keeping fresh of food |
| GB 13454-1992 | 氨基模塑料 | Plastics--Aminoplastic moulding materials--Specification |
| GB 1404.3-2008 | 塑料 粉狀酚醛模塑料 第3部分：選定模塑料的要求 | Plastics - Phenolic powder moulding compounds - Part 3: Requirements for selectes moulding compounds |
| GB 14232.1-2004 | 人體血液及血液成分袋式塑料容器第1部分:傳統型血袋 | Plastics collapsible containers for human blood and blood components--Part1:Conventional containers |
| GB 15593-1995 | 輸血(液)器具用軟聚氯乙烯塑料 | Plasticized polyvinyl chloride (PVC) compounds for transfusion (infusion) equipment |
| GB 16487.12-2005 | 進口可用作原料的固體廢物環境保護控制標準廢塑料 | Environmental protection control standard for imported solid wastes as raw materials -- Waste and scrap of plastics |
| GB 18006.1-2009 | 塑料一次性餐飲具通用技術要求 | General requirement of plastic disposable tableware |
| GB 18072-2000 | 塑料廠衛生防護距離標準 | Health protection zone standard for plastics plant |
| GB 18191-2008 | 包裝容器 危險品包裝用塑料桶 | Packing containers - Plastic drum for packages of dangerous goods |
| GB 19160-2008 | 包裝容器 危險品包裝用塑料罐 | Packing containers - Plastic jerrican for packages of dangerous goods |
| GB 19434.8-2004 | 危險貨物剛性塑料中型散裝容器檢驗安全規范性能檢驗 | Safety code for theinspection of rigid plastics IBCs for dangerous goods--Performance tests |
| GB 19741-2005 | 液體食品包裝用塑料復合膜、袋 | The plastics laminated films and bags using for packaging of liquid food |
| GB 20265-2006 | 耐化學品的工業用模壓塑料靴 | Moulded plastics industrial boots with chemical resistance |
| GB 21660-2008 | 塑料購物袋的環保、安全和標識通用技術要求 | The general requirement for environmental protection, safety, identification and marking of plastic shopping bags |
| GB 22530-2008 | 橡膠塑料注射成型機安全要求 | Safety requirements of injection moulding machines for rubber and plastics |
| GB/T 10004-2008 | 包裝用塑料復合膜、袋 干法復合、擠出復合 | Plastic laminated films & pouches for packaging dry lamination & extrusion lamination |
| GB/T 10006-1988 | 塑料薄膜和薄片摩擦系數測定方法 | Plastics--Film and sheeting--Determination of the coefficients of friction |
| GB/T 10007-2008 | 硬質泡沫塑料 剪切強度試驗方法 | Rigid cellular plastics - Determination of shear strength |
| GB/T 10009-1988 | 丙烯腈-丁二烯-苯乙烯(ABS)塑料擠出板材 | Acrylenitrile-butadiene-styrene (ABS) plastics extrusion plates |
| GB/T 1033.1-2008 | 塑料 非泡沫塑料密度的測定 第1部分：浸漬法、液體比重瓶法和滴定法 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method |
| GB/T 1034-2008 | 塑料 吸水性的測定 | Plastics - Determination of water absorption |
| GB/T 1036-2008 | 塑料 -30℃～30℃線膨脹系數的測定 石英膨脹計法 | Test method for coefficient of linear thermal expansion of plastics between -30℃ and 30℃ with a vitreous silica dilatometer |
| GB/T 1037-1988 | 塑料薄膜和片材透水蒸氣性試驗方法杯式法 | Test method for water vapor transmission of plastic film and sheet--Cup method |
| GB/T 1038-2000 | 塑料薄膜和薄片氣體透過性試驗方法壓差法 | Plastics--Film and sheeting--Determination of gas transmission--Differential-pressure method |
| GB/T 1040.1-2006 | 塑料拉伸性能的測定第1部分：總則 | Plastics - Determination of tensile properties - Part 1: General principles |
| GB/T 1040.2-2006 | 塑料拉伸性能的測定第2部分：模塑和擠塑塑料的試驗條件 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics |
| GB/T 1040.3-2006 | 塑料拉伸性能的測定第3部分：薄膜和薄片的試驗條件 | Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets |
| GB/T 1040.4-2006 | 塑料拉伸性能的測定第4部分：各向同性和正交各向異性纖維增強復合材料的試驗條件 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| GB/T 1040.5-2008 | 塑料 拉伸性能的測定 第5部分：?jiǎn)蜗蚶w維增強復合材料的試驗條件 | Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites |
| GB/T 1041-2008 | 塑料 壓縮性能的測定 | Plastics - Detemination of compressive properties |
| GB/T 1043.1-2008 | 塑料 簡支梁沖擊性能的測定 第1部分：非儀器化沖擊試驗 | Plastics - Determination of charpy impact properties - Part 1: Non - instrumented impact test |
| GB/T 10798-2001 | 熱塑性塑料管材通用壁厚表 | Thermoplastics pipes--Universal wall thickness table |
| GB/T 10799-2008 | 硬質泡沫塑料 開孔和閉孔體積百分率的測定 | Rigid cellular plastics - Determination of the volume percentage of open cells and of closed cells |
| GB/T 10801.1-2002 | 絕熱用模塑聚苯乙烯泡沫塑料 | Moulded polystyrene foam board for thermal insulation |
| GB/T 10801.2-2002 | 絕熱用擠塑聚苯乙烯泡沫塑料(XPS) | Rigid extruded polystyrene foam board for thermal insulation (XPS) |
| GB/T 10802-2006 | 通用軟質聚醚型聚氨酯泡沫塑料 | General flexible polyether polyurethane cellular plastics |
| GB/T 11016.1-2009 | 塑料絕緣和橡皮絕緣電話軟線 第1部分：一般規定 | Plastic or rubber insulated telephone cords - Part 1: General |
| GB/T 11016.2-2009 | 塑料絕緣和橡皮絕緣電話軟線 第2部分：聚氯乙烯絕緣電話軟線 | Plastic or rubber insulated telephone cords - Part 2: Polyvinyl chloride insulated telephone cords |
| GB/T 11016.3-2009 | 塑料絕緣和橡皮絕緣電話軟線 第3部分：聚丙烯絕緣電話軟線 | Plastic or rubber insulated telephone cords - Part 3: Polypropylene insulated telephone cords |
| GB/T 11016.4-2009 | 塑料絕緣和橡皮絕緣電話軟線 第4部分：橡皮絕緣電話軟線 | Plastic or rubber insulated telephone cords - Part 4: Rubber insulated telephone cords |
| GB/T 11546.1-2008 | 塑料 蠕變性能的測定 第1部分：拉伸蠕變 | Plastic - Determination of creep behaviour - Part 1: Tensile creep |
| GB/T 11547-2008 | 塑料 耐液體化學試劑性能的測定 | Plastic - Methods of test for the determination of the effects of immersion in liquid chemicals |
| GB/T 11548-1989 | 硬質塑料板材耐沖擊性能試驗方法 (落錘法) | Standard test method for impact resistance of rigid plastic sheeting by means of a tup (falling weight) |
| GB/T 11793-2008 | 未增塑聚氯乙烯（PVC-U）塑料門窗力學性能及耐候性試驗方法 | Test methods on mechanical and weathering properties for unplasticized polyvinyl chloride (PVC-U) doors and windows |
| GB/T 11997-2008 | 塑料 多用途試樣 | Plastic - Multipurpose test specimens |
| GB/T 11998-1989 | 塑料玻璃化溫度測定方法熱機械分析法 | Determination of glass transitiontemperature of plastics--Thermomechanical analysis |
| GB/T 12000-2003 | 塑料暴露于濕熱、水噴霧和鹽霧中影響的測定 | Determination of the effects of exposure to damp heat，water spray and salt mist for plastics |
| GB/T 12001.1-2008 | 塑料 未增塑聚氯乙烯模塑和擠出材料 第1部分：命名系統和分類基礎 | Plastics - Unplasticized poly (vinyl chloride) (PVC-U) moulding and extruded materials - Part 1: Designation system and basis for specifications |
| GB/T 12001.2-2008 | 塑料 未增塑聚氯乙烯模塑和擠出材料 第2部分：試樣制備和性能測定 | Plastics - Unplasticized poly (vinyl chloride) (PVC-U) moulding and extruded materials - Part 2: Preparation of test specimens and determination of properties |
| GB/T 12002-1989 | 塑料門窗用密封條 | Sealing strips for plastic doors and windows |
| GB/T 12003-2008 | 未增塑聚氯乙烯（PVC-U）塑料窗 外形尺寸的測定 | Unplasticized polyvinyl chloride(PVC-U) windows - Determination of dimensions |
| GB/T 12006.1-2009 | 塑料 聚酰胺 第1部分：黏數測定 | Plastics - Polyamides - Part 1: Determination of viscosity number |
| GB/T 12006.2-2009 | 塑料 聚酰胺 第2部分：含水量測定 | Plastics - Polyamides - Part 2: Determination of water content |
| GB/T 12008.1-2009 | 塑料 聚醚多元醇 第1部分：命名系統 | Plastics - Polyether polyols - Part 1: Designation system |
| GB/T 12008.3-2009 | 塑料 聚醚多元醇 第3部分：羥值的測定 | Plastics - Polyether polyols - Part 3: Determination of hydroxyl number |
| GB/T 12008.4-2009 | 塑料 聚醚多元醇 第4部分：鈉和鉀的測定 | Plastics - Polyether polyols - Part 4: Determination of sodium and potassium |
| GB/T 12009.3-2009 | 塑料 多亞甲基多苯基異氰酸酯 第3部分：黏度的測定 | Plastics - Polymethylene polyphenyl isocyanate - Part 3: Determination of viscosity |
| GB/T 12010.1-2008 | 塑料 聚乙烯醇材料（PVAL） 第1部分：命名系統和分類基礎 | Plastics - Poly(vinyl alcohol)(PVAL) materials - Part 1: Designation system and basis for specifications |
| GB/T 12027-2004 | 塑料薄膜和薄片加熱尺寸變化率試驗方法 | Plastics--Film and sheeting--Determination of dimensional change on heating |
| GB/T 12554-2006 | 塑料注射模技術條件 | Specifiication of injection moulds for plastics |
| GB/T 12555-2006 | 塑料注射模模架 | Injection mould bases for plastics |
| GB/T 12556-2006 | 塑料注射模模架技術條件 | Specification of injection mould bases for plastics |
| GB/T 12584-2008 | 橡膠或塑料涂覆織物 低溫沖擊試驗 | Rubber or plastics coated fabrics - Low-temperature impact test |
| GB/T 12586-2003 | 橡膠或塑料涂覆織物耐屈撓破壞性的測定 | Rubber or plastics-coated fabrics--Determination of resistance to damage by flexing |
| GB/T 12587-2003 | 橡膠或塑料涂覆織物抗壓裂性的測定 | Rubber or plastics-coated fabrics--Determination of crush resistance |
| GB/T 12588-2003 | 塑料涂覆織物聚氯乙烯涂覆層融合程度快速檢驗法 | Plastics coated fabrics--Polyvinyl chloride coatings--Rapid method for checking fusion |
| GB/T 12600-2005 | 金屬覆蓋層塑料上鎳+鉻電鍍層 | Metallic coatings Electroplated coatings of nickel plus chromium on plastics materials |
| GB/T 12722-2008 | 橡膠和塑料軟管組合件 液壓脈沖曲撓試驗（半Ω試驗） | Rubber and plastics hose assemblies - Flexing combined with hydraulic impulse test（half-omega test） |
| GB/T 12783-2000 | 橡膠塑料機械產品型號編制方法 | Editorial nominating method for the modeldesignation of rubber and plastics machinery |
| GB/T 12784-1991 | 橡膠塑料加壓式捏煉機 | Dispersion mixer for rubber and plastics |
| GB/T 12811-1991 | 硬質泡沫塑料平均泡孔尺寸試驗方法 | Test method for average cell size of rigid cellular plastics |
| GB/T 12812-2006 | 硬質泡沫塑料 易碎性的測定 | Rigid cellular plastics - Determination of friability |
| GB/T 12833-2006 | 橡膠和塑料撕裂強度和粘合強度測定中的多峰曲線分析 | Rubber and plastics - Analysis of multipeak traces obtained in determinations of tear strength and adhesion strength |
| GB/T 12949-1991 | 滑動軸承覆有減摩塑料層的雙金屬軸套 | Plain bearings--Bimetallic busheswith plastic overlay |
| GB/T 13096-2008 | 拉擠玻璃纖維增強塑料桿力學性能試驗方法 | Test method for mechanical properties of pultruded glass fiber reinforced plastic rods |
| GB/T 13376-2008 | 塑料閃爍體 | Plastic scintillators |
| GB/T 13455-1992 | 氨基模塑料揮發物測定方法 | Plastics--Aminoplastic moulding materials--Determination of volatile matter |
| GB/T 13525-1992 | 塑料拉伸沖擊性能試驗方法 | Test method for tensile-impact property of plastics |
| GB/T 13578-1992 | 橡膠塑料壓延機 | Rubber and plactics calender |
| GB/T 13947-1992 | 電子元器件塑料封裝設備通用技術條件 | General specification for electronic components plastic packaging equipments |
| GB/T 1404.1-2008 | 塑料 粉狀酚醛模塑料 第1部分: 命名方法和基礎規范 | Plastics - Phenolic powder moulding compounds - Part 1: Designation system and basis for specifications |
| GB/T 1404.2-2008 | 塑料 粉狀酚醛模塑料 第2部分: 試樣制備和性能測定 | Plastics - Phenolic powder moulding compounds - Part 2: Preparation of test specimens and determination of properties |
| GB/T 14112-1993 | 半導體集成電路塑料雙列封裝沖制型引線框架規范 | Semiconductor integrated circuits--Specification for stamped leadframes of plastic DIP |
| GB/T 14152-2001 | 熱塑性塑料管材耐外沖擊性能試驗方法時針旋轉法 | Thermoplastics pipes--Determination of resistance to external blows--Round-the-clock method |
| GB/T 14153-1993 | 硬質塑料落錘沖擊試驗方法通則 | General test method for impact resistance of rigid plastics by means of falling weight |
| GB/T 14154-1993 | 塑料門垂直荷載試驗方法 | Plastics doors--Vertical load test |
| GB/T 14208.1-2009 | 紡織玻璃纖維增強塑料 無捻粗紗增強樹脂棒機械性能的測定 第1部分：通則和棒的制備 | Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Part 1: General considerations and preparation of rods |
| GB/T 14208.2-2009 | 紡織玻璃纖維增強塑料 無捻粗紗增強樹脂棒機械性能的測定 第2部分：彎曲強度的測定 | Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving- reinforced resin - Part 2: Determination of flexural strength |
| GB/T 14208.3-2009 | 紡織玻璃纖維增強塑料 無捻粗紗增強樹脂棒機械性能的測定 第3部分：壓縮強度的測定 | Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving- reinforced resin - Part 3: Determination of compressive strength |
| GB/T 14208.4-2009 | 紡織玻璃纖維增強塑料 無捻粗紗增強樹脂棒機械性能的測定 第4部分：表觀層間剪切強度的測定 | Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Part 4: Determination of apparent interlaminar shear strength |
| GB/T 14216-2008 | 塑料 膜和片潤濕張力的測定 | Plastics - Film and sheeting - Determination of wetting tension |
| GB/T 14234-1993 | 塑料件表面粗糙度 | Surface roughness for plastic parts |
| GB/T 14447-1993 | 塑料薄膜靜電性測試方法半衰期法 | Test method for electrostatic properties of plastic films--Half-life method |
| GB/T 1446-2005 | 纖維增強塑料性能試驗方法總則 | Fiber-reinforced plastics composites-The generals for determination of properties |
| GB/T 1447-2005 | 纖維增強塑料拉伸性能試驗方法 | Fiber-reinforced plastics composites---Determination of tensile properties |
| GB/T 1448-2005 | 纖維增強塑料壓縮性能試驗方法 | Fiber-reinforced plastics composites-Determination of compressive properties |
| GB/T 14484-2008 | 塑料 承載強度的測定 | Plastics - Determination of bearing strength |
| GB/T 14486-2008 | 塑料模塑件尺寸公差 | Dimensional tolerances for moulded plastic parts |
| GB/T 1449-2005 | 纖維增強塑料彎曲性能試驗方法 | Fibre-reinforced plastic composites-Determination of flexural properties |
| GB/T 1450.1-2005 | 纖維增強塑料層間剪切強度試驗方法 | Fibre-reinforced plastic composites-Determination of interlaminar shear strength |
| GB/T 1450.2-2005 | 纖維增強塑料沖壓式剪切強度試驗方法 | Fibre-reinforced plastic composites-Determination of the punch-type shear strength |
| GB/T 1451-2005 | 纖維增強塑料簡支梁式?jīng)_擊韌性試驗方法 | Fiber-reinforced plastics composites---Determination of Charpy impact properties |
| GB/T 14519-1993 | 塑料在玻璃板過濾后的日光下間接曝露試驗方法 | Plastics--Method of exposure to indirect weathering using glass-filtered daylight |
| GB/T 14520-1993 | 氣相色譜分析法測定不飽和聚酯樹脂增強塑料中的殘留苯乙烯單體含量 | Determination of residual styrene monomer content in reinforced plastics based on unsaturated polyester resins by gas chromatography |
| GB/T 14522-2008 | 機械工業產品用塑料、涂料、橡膠材料人工氣候老化試驗方法 熒光紫外燈 | Artificial weathering test method for plastics,coating and rubber materials used for machinery industrial products - Fluorescent UV lamps |
| GB/T 1458-2008 | 纖維纏繞增強塑料環形試樣力學性能試驗方法 | Test method for mechanical properties of ring of filament-winding reinforced plastics |
| GB/T 1462-2005 | 纖維增強塑料吸水性試驗方法 | Test methods for water absorption of fiber reinforced plastics |
| GB/T 1463-2005 | 纖維增強塑料密度和相對密度試驗方法 | Test methods for density and relative density of fiber reinforced plastics |
| GB/T 14904-1994 | 鋼絲增強的橡膠、塑料軟管和軟管組合件屈撓液壓脈沖試驗 | Rubber and plastics hose and hose assemblies--Wire reinforced--Hydraulic impulse test with flexing |
| GB/T 14905-2009 | 橡膠和塑料軟管 各層間粘合強度的測定 | Rubber and plastics hoses - Determination of adhesion between components |
| GB/T 15047-1994 | 塑料扭轉剛性試驗方法 | Test method for stiffness proporties in torsion of plastics |
| GB/T 15048-1994 | 硬質泡沫塑料壓縮蠕變?cè)囼?yàn)方法 | Cellular plastics，rigid--Determination of compressive creep |
| GB/T 15065-2009 | 電線電纜用黑色聚乙烯塑料 | Black polyethylene compounds for wire and cable |
| GB/T 15223-2008 | 塑料 液體樹脂 用比重瓶法測定密度 | Plastics - Liquid resins - Determination of density by the pyknometer method |
| GB/T 15234-1994 | 塑料平托盤 | Plastics flat pallets |
| GB/T 15560-1995 | 流體輸送用塑料管材液壓瞬時爆破和耐壓試驗方法 | Standard test method for short-time hydraulic failure and resistance to constant internal pressure of the plastics pipes for the transport of fluids |
| GB/T 15568-2008 | 通用型片狀模塑料(SMC) | Sheet molding compound(SMC) for general purposes |
| GB/T 15596-2009 | 塑料在玻璃下日光、自然氣候或?qū)嶒?yàn)室光源暴露后顏色和性能變化的測定 | Plastics - Determination of changes in colour and variations in properties after exposure to daylight under glass，natural weathering or laboratory light sources |
| GB/T 15597.1-2009 | 塑料 聚甲基丙烯酸甲酯（PMMA）模塑和擠塑材料 第1部分：命名系統和分類基礎 | Plastics - Poly(methyl methacrylate)(PMMA)moulding and extrusion materials - Part 1: Designation system and basis for specifications |
| GB/T 15662-1995 | 導電、防靜電塑料體積電阻率測試方法 | Method of testing volume resistivity of conducting and antistatic plastics |
| GB/T 15738-2008 | 導電和抗靜電纖維增強塑料電阻率試驗方法 | Test method for resistivity of conducting and antistatic fiber reinforced plastics |
| GB/T 15876-1995 | 塑料四面引線扁平封裝引線框架規范 | Specification of leadframes for plastic quad flat package |
| GB/T 15907-2008 | 橡膠和塑料軟管 可燃性試驗方法 | Rubber and plastics hoses - Method of test for flammability |
| GB/T 15908-2009 | 塑料軟管及軟管組合件 液壓用織物增強型 規范 | Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - Specification |
| GB/T 15928-2008 | 不飽和聚酯樹脂基增強塑料中殘留苯乙烯單體含量的測定 | Reinforced plastics based on unsaturated polyester resins - Determination of residual styrene monomer content |
| GB/T 16167-2009 | 救生艇殼體玻璃纖維增強塑料層合板技術條件 | Technical conditions of lifeboat glass fiber reinforced plastics laminate |
| GB/T 16273.5-2002 | 設備用圖形符號第5部分:塑料機械通用符號 | Graphical symbols for use on equipment--Part 5:Common symbols for plastic machine |
| GB/T 16276-1996 | 塑料薄膜粘連性試驗方法 | Test method for blocking of plastic film |
| GB/T 16288-2008 | 塑料制品的標志 | Marking of plastics products |
| GB/T 1630.1-2008 | 塑料 環氧樹脂 第1部分：命名 | Plastics - Epoxy resins - Part 1: Designation |
| GB/T 1632.1-2008 | 塑料 使用毛細管粘度計測定聚合物稀溶液粘度 第1部分：通則 | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part1:General principles |
| GB/T 1632.5-2008 | 塑料 使用毛細管粘度計測定聚合物稀溶液粘度 第5部分：熱塑性均聚和共聚型聚酯(TP) | Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 5 : Thermoplastic polyester(TP) homopolymers and copolymers |
| GB/T 1633-2000 | 熱塑性塑料維卡軟化溫度(VST)的測定 | Plastics--Thermoplastic materials--Determination of Vicat softening temperature(VST) |
| GB/T 1634.1-2004 | 塑料負荷變形溫度的測定第1部分:通用試驗方法 | Plastics--Determination of temperature of deflection under load--Part 1:General test method |
| GB/T 1634.2-2004 | 塑料負荷變形溫度的測定第2部分:塑料、硬橡膠和長纖維增強復合材料 | Plastics--Determination of temperature of deflection under load--Part 2:Plastics，ebonite and long-fibre-reinforced composites |
| GB/T 1634.3-2004 | 塑料負荷變形溫度的測定第3部分:高強度熱固性層壓材料 | Plastics--Determination of temperature of deflection under load--Part 3:High-strength thermosetting laminates |
| GB/T 1636-2008 | 塑料 能從規定漏斗流出的材料表觀密度的測定 | Plastics - Determination of apparent density material that can be poured from a specified funnel |
| GB/T 16422.1-2006 | 塑料實驗室光源暴露試驗方法第1部分：總則 | Plastics - Methods of the exposure to laboratory light sources - Part 1: General guidance |
| GB/T 16422.2-1999 | 塑料實驗室光源暴露試驗方法第2部分:氙弧燈 | Plastics--Methods of exposure to laboratory light sources--Part 2:Xenon-arc sources |
| GB/T 16422.3-1997 | 塑料實驗室光源曝露試驗方法第3部分:熒光紫外燈 | Plastics--Methods of exposure to laboratory light sources--Part 3:Fluorescent UV lamps |
| GB/T 16422.4-1996 | 塑料實驗室光源曝露試驗方法第4部分:開放式碳弧燈 | Plastics--Methodsof exposure to laboratory light sources--Part 4:Open flame carbon arc lamp |
| GB/T 16525-1996 | 塑料有引線片式載體封裝引線框架規范 | Specification of leadframes for plastic leaded chip carrier packages |
| GB/T 16578.1-2008 | 塑料 薄膜和薄片 耐撕裂性能的測定 第1部分: 褲形撕裂法 | Plastics - Film and sheeting - Determination of tear resistance - Part 1：Trouser tear method |
| GB/T 16578.2-2009 | 塑料 薄膜和薄片 耐撕裂性能的測定 第2部分：埃萊門多夫（Elmendor）法 | Plastics - Film and sheeting - Determination of tear resistance - Part 2: Elmendorf method |
| GB/T 16582-2008 | 塑料 用毛細管法和偏光顯微鏡法測定部分結晶聚合物熔融行為（熔融溫度或熔融范圍） | Plastics - Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
| GB/T 16613-2008 | 塑料 試驗用聚氯乙烯（PVC）糊的制備 分散器法 | Plastics - Preparation of PVC pastes for test purposes - Dissolver method |
| GB/T 16778-2009 | 纖維增強塑料結構件失效分析一般程序 | General procedure of failure analysis for fiber reinforced plastic structural products |
| GB/T 16779-2008 | 纖維增強塑料層合板拉-拉疲勞性能試驗方法 | Test method for tension-tension fatigue of fiber reinforced plastic laminates |
| GB/T 17037.1-1997 | 熱塑性塑料材料注塑試樣的制備第1部分:一般原理及多用途試樣和長條試樣的制備 | Injection moulding of test specimens of thermoplastic materials--Part 1:General principles and moulding of multipurpose and bar test specimens |
| GB/T 17037.3-2003 | 塑料熱塑性塑料材料注塑試樣的制備第3部分: 小方試片 | Plastics--Injection moulding of test specimens of thermoplastic materials--Part 3: Small plates |
| GB/T 17037.4-2003 | 塑料熱塑性塑料材料注塑試樣的制備第4部分: 模塑收縮率的測定 | Plastic--Injection moulding of test specimens of thermoplastic materials--Part 4: Determination of moulding shrinkage |
| GB/T 17200-2008 | 橡膠塑料拉力、壓力和彎曲試驗機（恒速驅動） 技術規范 | Technical specification for tensile, compression and flexural testing machines for rubber and plastics (constant rate of rtaverse) |
| GB/T 1725-2007 | 色漆、清漆和塑料 不揮發物含量的測定 | Paints,varnishes and plastics - Determination of non-volatile-matter content |
| GB/T 17603-1998 | 光解性塑料戶外暴露試驗方法 | Method for outdoor exposure testing of photodegradable plastics |
| GB/T 17689-2008 | 土工合成材料 塑料土工格柵 | Geosynthetics - Plastic geogrids |
| GB/T 17690-1999 | 土工合成材料塑料扁絲編織土工布 | Geosynthetics--Plastic woven film yarn geotextile |
| GB/T 17858.2-1999 | 包裝術語工業包裝袋熱塑性塑料軟質薄膜袋 | Packaging--Sacks--Vocabulary and types--Sacks made from thermoplastic flexible film |
| GB/T 17876-1999 | 包裝容器塑料防盜瓶蓋 | Packaging volume--Plastic pilferproof closure |
| GB/T 18022-2000 | 聲學1～10 MHz頻率范圍內橡膠和塑料縱波聲速與衰減系數的測量方法 | Acoustics--Methods for measuring the longitudinal sound speed and attenuation coefficient of rubbers and plastics in the frequency range 1 MHz to 10 MHz |
| GB/T 18042-2000 | 熱塑性塑料管材蠕變比率的試驗方法 | Thermoplastics pipes--Determination of creep ratio |
| GB/T 18252-2008 | 塑料管道系統 用外推法確定熱塑性塑料材料以管材形式的長期靜液壓強度 | Plastics piping and ducting systems - Determination of the long - term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| GB/T 1842-2008 | 塑料 聚乙烯環境應力開裂試驗方法 | Plastics - Test method for environmental stress-cracking of polyethylene |
| GB/T 18422-2001 | 橡膠和塑料軟管及軟管組合件透氣性的測定 | Rubber and plastics hoses andhose assemblies--Determination of permeability to gas |
| GB/T 18423-2001 | 橡膠和塑料軟管及非增強軟管液體壁透性測定 | Rubber and plastics hoses and tubing--Determination of transmission of liquids through hose and tubing walls |
| GB/T 18424-2001 | 橡膠和塑料軟管氙弧燈曝曬顏色和外觀變化的測定 | Rubber and plastics hoses--Exposure to a xenon arc lamp--Determination of changes in colour andappearance |
| GB/T 18426-2001 | 橡膠或塑料涂覆織物低溫彎曲試驗 | Rubber or plastics-coated fabrics--Low-temperature bend test |
| GB/T 1843-2008 | 塑料 懸臂梁沖擊強度的測定 | Plastics - Determination of izod impact strength |
| GB/T 1844.1-2008 | 塑料 符號和縮略語 第1部分: 基礎聚合物及其特征性能 | Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics |
| GB/T 1844.2-2008 | 塑料 符號和縮略語 第2部分：填充及增強材料 | Plastic-Symbols and abbreviated-Part 2: Fillers and reinforcing materials |
| GB/T 1844.3-2008 | 塑料 符號和縮略語 第3部分：增塑劑 | Plastics - Symbols and abbrebiated terms - Part 3: Plasticizers |
| GB/T 1844.4-2008 | 塑料 符號和縮略語 第4部分: 阻燃劑 | Plastics - Symbols and abbreviated terms - Part 4: Flame retardants |
| GB/T 1845.2-2006 | 塑料聚乙烯 (PE) 模塑和擠出材料第2部分: 試樣制備和性能測定 | Plastics―Polyethylene(PE) moulding and extrusion materials―Part 2: Preparation of test specimens and determination of properties |
| GB/T 18475-2001 | 熱塑性塑料壓力管材和管件用材料分級和命名總體使用(設計)系數 | Thermoplastics materials for pipes and fittings for pressure applications classification and designation--Overall service(design) coefficient |
| GB/T 18689-2009 | 農業灌溉設備 小型手動塑料閥 | Agricultural irrigation equipment－ Manually operated small plastics valves |
| GB/T 18743-2002 | 流體輸送用熱塑性塑料管材簡支梁沖擊試驗方法 | Thermoplastics pipes for the transport of fluids--Determination of impact by the charpy method |
| GB/T 18744-2002 | 土工合成材料塑料三維土工網墊 | Geosynthetics--Plastic three dimensional erosion control mat |
| GB/T 18943-2008 | 多孔橡膠與塑料 動態緩沖性能測定 | Cellular rubbers and plastics - Determination of dynamic cushioning performance |
| GB/T 18949-2003 | 橡膠和塑料軟管動態條件下耐臭氧性能的評定 | Rubber and plastics hoses--Assessment of ozone resistance under dynamic conditions |
| GB/T 18950-2003 | 橡膠和塑料軟管靜態下耐紫外線性能測定 | Rubber and plastics hoses--Determination of ultra-violet resistance under static conditions |
| GB/T 18964.1-2008 | 塑料 抗沖擊聚苯乙烯(PS-I)模塑和擠出材料 第1部分：命名系統和分類基礎 | Plastics － Impact-resistant Polystyrene (PS-I) moulding and extrusion materials －Part 1: Designation system and basis for specifications |
| GB/T 18964.2-2003 | 塑料抗沖擊聚苯乙烯(PS-I)模塑和擠出材料第2部分: 試樣制備和性能測定 | Plastics--Impact-resistant polystyrene(PS-I) moulding and extrusion materials--Part 2: Preparation of test specimens and determination of properties |
| GB/T 18991-2003 | 冷熱水系統用熱塑性塑料管材和管件 | Thermoplastics pipes and fittings forhot and cold water systems |
| GB/T 19089-2003 | 橡膠或塑料涂覆織物耐磨性的測定馬丁代爾法 | Rubber-or plastics-coated fabrics--Determination of abrasion resistance--Martindale method |
| GB/T 19274-2003 | 土工合成材料塑料土工格室 | Geosynthetics--Plastic geocell |
| GB/T 19278-2003 | 熱塑性塑料管材、管件及閥門通用術語及其定義 | General terms and their definitions of thermoplastic pipes，fittings and valves |
| GB/T 19280-2003 | 流體輸送用熱塑性塑料管材耐快速裂紋擴展(RCP)的測定小尺寸穩態試驗(S4試驗) | Thermoplastics pipes for the conveyance of fluids--Determination of resistance to rapid crack propagation (RCP)--Small-scale steady-state test(S4 test) |
| GB/T 19314.1-2003 | 小艇艇體結構和構件尺寸第1部分:材料:熱固性樹脂、玻璃纖維增強塑料、基準層合板 | Small craft--Hull construction and scantlings--Part 1: Materials: Thermosetting resins，glass-fibre reinforcement，reference laminate |
| GB/T 19466.1-2004 | 塑料差示掃描量熱法(DSC)第1部分:通則 | Plastics--Differential scanning calorimetry(DSC)--Part 1:General principles |
| GB/T 19466.2-2004 | 塑料差示掃描量熱法(DSC)第2部分:玻璃化轉變溫度的測定 | Plastics--Differential scanning calorimetry(DSC)--Part 2:Determination of glass transition temperature |
| GB/T 19466.3-2004 | 塑料差示掃描量熱法(DSC)第3部分:熔融和結晶溫度及熱焓的測定 | Plastics--Differential scanning calorimetry(DSC)--Part 3:Determination of temperatureand enthalpy of melting and crystallization |
| GB/T 19466.6-2009 | 塑料 差示掃描量熱法（DSC）第6部分：氧化誘導時間(等溫OIT)和氧化誘導溫度（動態OIT）的測定 | Plastics - Differential scanning calorimetry（DSC）- Part 6: Determination of oxidation induction time（isothermal OIT）and oxidation induction temperature（dynamic OIT） |
| GB/T 19467.1-2004 | 塑料可比單點數據的獲得和表示第1部分:模塑材料 | Plastics--Acquisition and presentation of comparable single-point data--Part 1:Moulding materials |
| GB/T 19467.2-2004 | 塑料可比單點數據的獲得和表示第2部分:長纖維增強材料 | Plastics--Acquisition and presentation of comparable single-point data--Part 2:Long-fibre-reinforced plastics |
| GB/T 19470-2004 | 土工合成材料塑料土工網 | Geosythetics--Plastic geonet |
| GB/T 19471.1-2004 | 塑料管道系統硬聚氯乙烯(PVC-U)管材彈性密封圈式承口接頭偏角密封試驗方法 | Plastics piping systems--Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride)(PVC-U)pipes--Test method forleaktighness under internal pressure and angular deflection |
| GB/T 19471.2-2004 | 塑料管道系統硬聚氯乙烯(PVC-U)管材彈性密封圈式承口接頭負壓密封試驗方法 | Plastics piping systems--Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride)(PVC-U)for use with PVC-U pipes--Test method for leaktightness under negative pressure |
| GB/T 19532-2004 | 包裝材料氣相防銹塑料薄膜 | Packaging material--Volatile corrosion inhibiting film |
| GB/T 19603-2004 | 塑料無滴薄膜無滴性能試驗方法 | Test method for drop-proof properties ofdrop-proof plastic films |
| GB/T 19647-2005 | 農田排水用塑料單壁波紋管 | Single wall corrugated plastics pipes for agricultural drainage |
| GB/T 19687-2005 | 閉孔塑料長期熱阻變化的測定實驗室加速測試方法 | Determination of the long-term change in thermal resistance of closed-cell plastics(accelerated laboratory test methods) |
| GB/T 19701.2-2005 | 外科植入物超高分子量聚乙烯第2部分:模塑料 | Implants for surgery Ultra-high molecular weight polyethylene-part 2:Moulded forms |
| GB/T 19712-2005 | 塑料管材和管件聚乙烯(PE)鞍形旁通抗沖擊試驗方法 | Plastics pipes and fittingsPolyethylene(PE) tapping tees Test method for impact resistance |
| GB/T 19789-2005 | 包裝材料塑料薄膜和薄片氧氣透過性試驗庫侖計檢測法 | Packaging Material Standard Test Method for Oxygen Gas Permeability Characteristics of Plastic Film and Sheeting Using a Coulometric Sensor |
| GB/T 19796-2005 | 農業灌溉設備聚乙烯承壓管用塑料鞍座 | Agricultural irrigation equipment-Plastics saddles for polyethylene pressure pipes |
| GB/T 19806-2005 | 塑料管材和管件聚乙烯電熔組件的擠壓剝離試驗 | Plastics pipes and fittings Crushing decohesion test for polyethylene(PE)electrofusion assemblies |
| GB/T 19807-2005 | 塑料管材和管件聚乙烯管材和電熔管件組合試件的制備 | Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting |
| GB/T 19808-2005 | 塑料管材和管件公稱外徑大于或等于90mm的聚乙烯電熔組件的拉伸剝離試驗 | Plastics pipes and fittings Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| GB/T 19809-2005 | 塑料管材和管件聚乙烯(PE)管材/管材或管材/管件熱熔對接組件的制備 | Plastics pipes and fittings-Preparation of polyethylene(PE)pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| GB/T 19811-2005 | 在定義堆肥化中試條件下塑料材料崩解程度的測定 | Plastics-Determination of the degree of disintegration of plastic materials under defined composting conditions in a pilot-scale test |
| GB/T 19812.1-2005 | 塑料節水灌溉器材單翼迷宮式滴灌帶 | Plastic equipment for water saving irrigation-drip tape with labyrinth on one side |
| GB/T 19812.2-2005 | 塑料節水灌溉器材壓力補償式滴頭及滴灌管 | Plastic equipment for water saving irrigation-Pressure compensating emitter and emitting pipe |
| GB/T 19812.3-2008 | 塑料節水灌溉器材 內鑲式滴灌管、帶 | Plastic equipment for water saving irrigation - Drip pipe and tape inlaid with emitters inside |
| GB/T 19993-2005 | 冷熱水用熱塑性塑料管道系統 管材管件組合系統熱循環試驗方法 | Thermoplastics piping systems for hot and cold water supply-Test method for the resiance of pipes and fittings mounted assemblies to thermal cycling |
| GB/T 20022-2005 | 塑料氯乙烯均聚和共聚樹脂表觀密度的測定 | Plastics -- Homopolymer and Copolymer resins of vinyl chloride Determination of apparent density |
| GB/T 20023-2005 | 無氣噴涂用橡膠和/或塑料軟管及軟管組合件 | Rubber and/or plastics hoses and hoses assemblies for airless paint spraying |
| GB/T 20024-2005 | 內燃機用橡膠和塑料燃油軟管可燃性試驗方法 | Rubber and Plastics hoses for fuels for internal-combustion engines -- Method of test for flammability |
| GB/T 20025.2-2005 | 汽車空調用橡膠和塑料軟管及軟管組合件耐制冷劑134a | Rubber and plastics hoses and hose assemblise for automotive air conditioning -- Refrigerant 134a |
| GB/T 20026-2005 | 橡膠和塑料軟管內襯層耐磨性測定 | Rubber and plastics hose -- Determination of abrasion of lining |
| GB/T 20027-2005 | 橡膠或塑料涂覆織物破裂強度的測定 | Rubber-or plastics-coated fabrics -- Determiation of bursting strength |
| GB/T 20197-2006 | 降解塑料的定義、分類、標識和降解性能要求 | Define, classify, marking and degradability requirement of degradable plastic |
| GB/T 20219-2006 | 噴涂硬質聚氨酯泡沫塑料 | Cellular plastics, rigid - Spray-applied polyurethane foam for thermal insulation of buildings - Specification |
| GB/T 20220-2006 | 塑料薄膜和薄片樣品平均厚度，卷平均厚度及單位質量面積的測定稱量法（稱量厚度） | Plastics - Film and sheeting - Determination of average thickness of a sample, and average thickness and yield of a roll, by gravimetric techniques (gravimetric thickness) |
| GB/T 2035-2008 | 塑料術語及其定義 | Terms and definitions for plastics |
| GB/T 20417.1-2008 | 塑料 丙烯腈-丁二烯-苯乙烯(ABS)模塑和擠出材料 第1部分：命名系統和分類基礎 | Plastics － Acrylonitrile-butadiene-Styrene(ABS) moulding and extrusion materials － Part 1: Designation system and basis for specifications |
| GB/T 20417.2-2006 | 塑料丙烯腈-丁二烯-苯乙烯 (ABS) 模塑和擠出材料第2部分:試樣制備和性能測定 | Plastics―Acrylonitrile-butadiene-styrene(ABS)moulding and extrusion materials―Part 2: Preparation of test specimens and determination of properties |
| GB/T 20463.1-2006 | 防水用橡膠或塑料涂覆織物 第1部分：聚氯乙烯涂覆織物 | Rubber or plastics-coated fabrics for water resistant clothing―Part 1: PVC-coated fabrics |
| GB/T 20463.2-2006 | 防水用橡膠或塑料涂覆織物 第2部分：防水透濕聚氨酯涂覆織物 | Rubber or plastics-coated fabrics for water-resistant clothing―Part 2: Waterproof and moisture penetrable polyurethane-coated fabric |
| GB/T 20672-2006 | 硬質泡沫塑料 在規定負荷和溫度條件下壓縮蠕變的測定 | Cellular plastics, rigid - Determination of compressive creep under specified load and temperature conditions |
| GB/T 20673-2006 | 硬質泡沫塑料 低于環境溫度的線膨脹系數的測定 | Cellular plastics - Determination of the coefficient of linear thermal expansion of rigid materials at sub-ambient temperatures |
| GB/T 20674.1-2006 | 塑料管材和管件 聚乙烯系統熔接設備 第1部分：熱熔對接 | Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 1：Butt fusion |
| GB/T 20674.2-2006 | 塑料管材和管件 聚乙烯系統熔接設備 第2部分：電熔連接 | Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 2: Electrofusion |
| GB/T 20875.1-2007 | 電氣絕緣材料水解穩定性的試驗方法 第1部分：塑料薄膜 | Method of test the hydrolytic stability of electrical insulating materials - Part 1: Plastic films |
| GB/T 21059-2007 | 塑料 液態或乳液態或分散體系聚合物/樹脂 用旋轉黏度計在規定剪切速率下黏度的測定 | Plastics - polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate |
| GB/T 21060-2007 | 塑料 流動性的測定 | Plastics - Determination of pourability |
| GB/T 21189-2007 | 塑料簡支梁、懸臂梁和拉伸沖擊試驗用擺錘沖擊試驗機的檢驗 | Verification of pendulum impact-testing machines used for Charpy, lzod and tensile impact-testing of plastics |
| GB/T 21238-2007 | 玻璃纖維增強塑料夾砂管 | Glass fiber reinforced plastics mortar pipes |
| GB/T 21239-2007 | 纖維增強塑料層合板沖擊后壓縮性能試驗方法 | Test method for compression after impact properties of fiber reinforced plastic laminates |
| GB/T 21300-2007 | 塑料管材和管件 不透光性的測定 | Plastics pipes and fittings - Determination of opacity |
| GB/T 21332-2008 | 硬質泡沫塑料 水蒸氣透過性能的測定 | Rigid cellular plastics - Determination of water vapour transmission properties |
| GB/T 21333-2008 | 硬質泡沫塑料 自結皮高密度材料試驗方法 | Cellular plastics,rigid - Test methods for self-skinned,high-density materials |
| GB/T 21460.1-2008 | 塑料 苯乙烯-丙烯腈(SAN)模塑和擠出材料 第1部分：命名系統和分類基礎 | Plastics － Styrene-acrylonitrile (SAN) moulding and extrusion materials － Part 1: Designation system and basis for specifications |
| GB/T 21460.2-2008 | 塑料 苯乙烯-丙烯腈(SAN)模塑和擠出材料 第2部分: 試樣制備和性能測定 | Plastics - Styrene/acrylonitrile(SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties |
| GB/T 21461.1-2008 | 塑料 超高分子量聚乙烯（PE-UHMW）模塑和擠出材料 第1部分：命名系統和分類基礎 | Plastics - Ultra-high-molecular-weight polyethylene(PE-UHMW) moulding and extrusion materials - Part 1: Designation system and basis for specifications |
| GB/T 21461.2-2008 | 塑料 超高分子量聚乙烯(PE-UHMW)模塑和擠出材料 第2部分: 試樣制備和性能測定 | Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties |
| GB/T 21492-2008 | 玻璃纖維增強塑料頂管 | Glass fiber reinforced plastics jacking pipe |
| GB/T 21526-2008 | 結構膠粘劑 粘接前金屬和塑料表面處理導則 | Structural adhesives - Guidelines for the surface preparation of metals and plastics prior to adhesive bonding |
| GB/T 21529-2008 | 塑料薄膜和薄片水蒸氣透過率的測定 電解傳感器法 | Determination of water vapour transmission rate for plastic film and sheeting - Electrolytic detection sensor method |
| GB/T 21558-2008 | 建筑絕熱用硬質聚氨酯泡沫塑料 | Rigid polyurethane cellular plastics used in the thermal insulation of building |
| GB/T 21661-2008 | 塑料購物袋 | Plastic shopping bags |
| GB/T 21662-2008 | 塑料購物袋的快速檢測方法與評價 | The puick testing method and evaluation for plastic shopping bags |
| GB/T 21783-2008 | 塑料 毛細管法和偏光顯微鏡法測定部分結晶聚合物的熔融行為(烯融溫度或熔融范圍) | Plastics - Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
| GB/T 21843-2008 | 塑料 氯乙烯均聚和共聚樹脂 用機械篩測定粒徑 | Plastics - Vinyl chloride homopolymer and copolymer resins - Particle size determination by mechanical sieving |
| GB/T 21928-2008 | 食品塑料包裝材料中鄰苯二甲酸酯的測定 | Determination of phthalate esters in food plastic packaging materials |
| GB/T 21988-2008 | 塑料 氯乙烯均聚和共聚樹脂 水中篩分析 | Plastics-Vinyl chloride homopolymer and copolymer resins-Sieve analysis in water |
| GB/T 21989-2008 | 塑料 聚氯乙烯糊 用Severs流變儀測定表觀黏度 | Plastics - Poly(vinyl chloride)pastes - Determination of apparent viscosity using the severs rheometer |
| GB/T 21991-2008 | 塑料 試驗用聚氯乙烯（PVC）糊的制備 行星混合器法 | Plastics - Preparation of PVC paste for test purpose - Planetary-mixer method |
| GB/T 22040-2008 | 公路沿線設施塑料制品耐候性要求及測試方法 | Technical requirements and determination of weathering quality for plastics of highway furnatures |
| GB/T 22047-2008 | 土壤中塑料材料最終需氧生物分解能力的測定 采用測定密閉呼吸計中需氧量或測定釋放的二氧化碳的方法 | Plastics - Determination of the ultimate aerobic biodegradability in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved |
| GB/T 22048-2008 | 玩具及兒童用品 聚氯乙烯塑料中鄰苯二甲酸酯增塑劑的測定 | Toys and children’s products - Determination of phthalate plasticizers in polyvinyl chloride plastic |
| GB/T 22236-2008 | 塑料的檢驗 檢驗用塑料制品的粉碎 | Testing of plastics Size reduction of plastic products for test purposes |
| GB/T 22271.1-2008 | 塑料 聚甲醛（POM）模塑和擠塑材料 第1部分：命名系統和分類基礎 | Plastics - Polyoxymethylene(POM) moulding and extrusion materials - Part 1: Designation system and basis for specifications |
| GB/T 22271.2-2008 | 塑料 聚甲醛（POM）模塑和擠塑材料 第2部分：試樣制備和性能測定 | Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties |
| GB/T 22312-2008 | 塑料 聚丙烯酰胺 殘留丙烯酰胺含量測定方法 | Plastics - Polyacrylamide - Determination for residual acrylamide |
| GB/T 22313-2008 | 塑料 用于聚氨酯生產的多元醇 水含量的測定 | Plastics - Polyols for use in the production of polyurethan - Determination of water content |
| GB/T 22314-2008 | 塑料 環氧樹脂 黏度測定方法 | Plastics - Epoxide resins - Determination of viscosity |
| GB/T 22410-2008 | 包裝 危險貨物運輸包裝 塑料相容性試驗 | Packaging - Transport packaging for dangerous goods - Plastics compatibility testing |
| GB/T 22411-2008 | 危險貨物塑料編織包裝抗老化試驗方法 | Test method of antiaging for plastic woven packaging of dangerous goods |
| GB/T 22470-2008 | 電氣用環保型模塑料通用要求 | General requirements for environmentally friendly moulding compounds for electrical purpose |
| GB/T 22472-2008 | 儀表和設備部件用塑料的燃燒性測定 | Tests for flammability of plastic materials for parts in devices and appliances |
| GB/T 22776-2008 | 計時儀器用公差與配合 塑料件公差 | () |
| GB/T 22936-2008 | 花卉用酚醛泡沫塑料 | Phenolic floral foam |
| GB/T 23241-2009 | 灌溉用塑料管材和管件基本參數及技術條件 | Plastics pipes and fittings used for irrigation basic parameters and technical requirements |
| GB/T 23296.1-2009 | 食品接觸材料 塑料中受限物質 塑料中物質向食品及食品模擬物特定遷移試驗和含量測定方法以及食品模擬物暴露 | Materials and articles in contact with foodstuffs - Plastics substances subject to limitation - Guide to test methods for the specific migration of substances from plastics to foods and food simulants and the determination of substances in plastics and the selection of conditions of exposure to food simulants |
| GB/T 23296.11-2009 | 食品接觸材料 塑料中環氧乙烷和環氧丙烷含量的測定 氣相色譜法 | Food contact materials - Determination of ethylene oxide and propylene oxide in plastics - Gas chromatography |
| GB/T 23296.13-2009 | 食品接觸材料 塑料中氯乙烯單體的測定 氣相色譜法 | Food contact materials - Determination of vinyl chloride monomer in plastics - Gas chromatography |
| GB/T 23296.22-2009 | 食品接觸材料 塑料中異氰酸酯含量的測定 高效液相色譜法 | Food contact materials - Determination of isocyanates in plastics - High performance liquid chromatography |
| GB/T 23296.3-2009 | 食品接觸材料 塑料中1,3-丁二烯含量的測定 氣相色譜法 | Food contact materials - Determination of 1,3-butadiene in plastics - Gas chromatography |
| GB/T 23296.7-2009 | 食品接觸材料 塑料中表氯醇含量的測定 高效液相色譜法 | Food contact materials - Determination of epichlorohydrin in plastics - High performance liquid chromatography |
| GB/T 23641-2009 | 電氣用纖維增強不飽和聚酯模塑料(SMC/BMC) | Fiber reinforced unsaturated polyester moulding-compounds（SMC and BMC）for electrical purposes |
| GB/T 23652-2009 | 塑料 氯乙烯均聚和共聚樹脂 振實表觀密度的測定 | Plastics - PVC resins - Determination of compacted apparent bulk density |
| GB/T 23653-2009 | 塑料 通用型聚氯乙烯樹脂 熱增塑劑吸收量的測定 | Plastics - PVC resins for general use - Determination of hot plasticizer absorption |
| GB/T 23711.1-2009 | 氟塑料襯里壓力容器 電火花試驗方法 | Spark test method for pressure vessels lined with fluoroplastics |
| GB/T 23711.2-2009 | 氟塑料襯里壓力容器 耐低溫試驗方法 | Low temperature test method for pressure vessels lined with fluoroplastics |
| GB/T 23711.3-2009 | 氟塑料襯里壓力容器 耐高溫試驗方法 | High temperature test method for pressure vessels lined with fluoroplastics |
| GB/T 23711.4-2009 | 氟塑料襯里壓力容器 耐真空試驗方法 | Vacuum test method for pressure vessels lined with fluoroplastics |
| GB/T 23711.5-2009 | 氟塑料襯里壓力容器 熱脹冷縮試驗方法 | Expansion and contraction test method for pressure vessels lined with fluoroplastics |
| GB/T 23711.6-2009 | 氟塑料襯里壓力容器 壓力試驗方法 | Hydrostatic pressure test method for pressure vessels lined with fluoroplastics |
| GB/T 23913.5-2009 | 復合巖棉板耐火艙室 第5部分：塑料裝飾件 | Fire-resisting compartment of composite rock wool panel - Part 5: Plastic decoration parts |
| GB/T 2406.1-2008 | 塑料 用氧指數法測定燃燒行為 第1部分：導則 | Plastics - Determination of burning behaviour by oxygen index - Part 1: Guidance |
| GB/T 2406.2-2009 | 塑料 用氧指數法測定燃燒行為 第2部分：室溫試驗 | Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test |
| GB/T 2407-2008 | 塑料 硬質塑料小試樣與熾熱棒接觸時燃燒特性的測定 | Plastics - Determination of flammability characteristics of rigid plastics in the form of small specimens in contact with an incandescent rod |
| GB/T 2408-2008 | 塑料 燃燒性能的測定 水平法和垂直法 | Plastics - Determination of burning characteristics - Horizontal and vertical test |
| GB/T 2410-2008 | 透明塑料透光率和霧度的測定 | Determination of the luminous transmittance and haze of transparent plastics |
| GB/T 2411-2008 | 塑料和硬橡膠 使用硬度計測定壓痕硬度（邵氏硬度） | Plastics and ebonite - Determination of indentation hardness by means of a duronmeter(shore hardness) |
| GB/T 24113.1-2009 | 機械電氣設備 塑料機械計算機控制系統 第1部分：通用技術條件 | Electrical equipment of machines - Computer control systems for plastics machinery - Part 1: General requirements |
| GB/T 2412-2008 | 塑料 聚丙烯(PP)和丙烯共聚物熱塑性塑料等規指數的測定 | Plastics - Polypropylene(PP) and propylene copolymer thermoplastics - Determination of isotactic index |
| GB/T 24126-2009 | 橡膠和塑料軟管及軟管組合件 采購者、組裝者、安裝者和操作者使用指南 | Rubber and plastics hoses and hose assemblies - Guide for use by purchasers, assemblers, installers and operating personnel |
| GB/T 24127-2009 | 塑料抗藻性能試驗方法 | Testing method for determining algal resistance of plastics |
| GB/T 24128-2009 | 塑料防霉性能試驗方法 | Method for testing resistance of plastics to mold |
| GB/T 24132.1-2009 | 室內裝飾用塑料涂覆織物 第1部分：PVC涂覆針織物規范 | Plastics-coated fabrics for upholstery - Part 1: Specification for PVC-coated knitted fabrics |
| GB/T 24132.2-2009 | 室內裝飾用塑料涂覆織物 第2部分：聚氯乙烯涂覆編織織物規范 | Plastics-coated fabrics for upholstery - Part 2: Specification for PVC-coated woven fabrics |
| GB/T 24132.3-2009 | 室內裝飾用塑料涂覆織物 第3部分：聚氨酯涂覆編織織物規范 | Plastics-coated fabrics for upholstery - Part 3: Specification for polyurethane-coated woven fabrics |
| GB/T 24133-2009 | 橡膠或塑料涂覆織物 調節和試驗的標準環境 | Rubber-or plastics-coated fabrics - Standard atmospheres for conditioning and testing |
| GB/T 24134-2009 | 橡膠和塑料軟管 靜態條件下耐臭氧性能的評價 | Rubber and plastics hoses - Assessment of ozone resistance under static conditions |
| GB/T 24135-2009 | 橡膠或塑料涂覆織物 加速老化試驗 | Rubber or plastics coated fabrics - Accelerated ageing tests |
| GB/T 24136-2009 | 橡膠或塑料涂覆織物 耐液體性能的測定 | Rubber-or plastics-coated fabrics - Detetmination of resistance to liquids |
| GB/T 24144-2009 | 消防軟管 橡膠和塑料吸引軟管和軟管組合件 | Fire-fighting hoses - Rubber and plastics suction hoses and hose assemblies |
| GB/T 24148.1-2009 | 塑料 不飽和聚酯樹脂（UP-R） 第1部分：命名系統 | Plastics - Unsaturated-polyester resins (UP-R) - Part 1: Designation system |
| GB/T 24148.2-2009 | 塑料 不飽和聚酯樹脂（UP-R） 第2部分：試樣制備和性能測定 | Plastics - Unsaturated-polyester resins (UP-R) - Part 2: Preparation of test specimens and determination of properties |
| GB/T 24148.4-2009 | 塑料 不飽和聚酯樹脂(UP-R) 第4部分：粘度的測定 | Plastics - Unsaturated polyester resin - Part 4: Determination of viscosity |
| GB/T 24148.6-2009 | 塑料 不飽和聚酯樹脂 (UP-R) 第6部分：130℃反應活性測定 | Plastics - Unsaturated-polyester resins - Part 6: Determination of reactivity at 130℃ |
| GB/T 24149.1-2009 | 塑料 汽車用聚丙烯（PP）專用料 第1部分：保險杠 | Plastics - Polypropylene(PP) compound for automobile - Part 1: Bumper |
| GB/T 24150-2009 | 塑料 阻燃抗沖擊聚苯乙烯專用料 | Plastics - Flame retardant impact-resistant polystyrene compound |
| GB/T 24151-2009 | 塑料 玻璃纖維增強阻燃聚對苯二甲酸丁二醇酯專用料 | Plastics - Glass fiber reinforced and flame retardant poly(butylenes terephthalate) compound |
| GB/T 24282-2009 | 塑料 聚丙烯中二甲苯可溶物含量的測定 | Plastics - Determination of xylene-soluble matter in polypropylene |
| GB/T 24451-2009 | 慢回彈軟質聚氨酯泡沫塑料 | Low resilience flexible polyether polyurethane cellular plastics |
| GB/T 24453-2009 | 酒店客房用易耗塑料制品 | Plastic products used in guestroom of hotel |
| GB/T 24454-2009 | 塑料垃圾袋 | Plastic refuse sack |
| GB/T 24721.1-2009 | 公路用玻璃纖維增強塑料產品 第1部分：通則 | Glass fiber reinforced plastic product for highway - Part 1: General rule |
| GB/T 24721.2-2009 | 公路用玻璃纖維增強塑料產品 第2部分：管箱 | Glass fiber reinforced plastic product for highway - Part 2: Trunk |
| GB/T 24721.3-2009 | 公路用玻璃纖維增強塑料產品 第3部分：管道 | Glass fiber reinforced plastic product for highway - Part 3: Duct |
| GB/T 24721.4-2009 | 公路用玻璃纖維增強塑料產品 第4部分：非承壓通信井蓋 | Glass fiber reinforced plastic product for highway - Part 4: Non-pressure communications well lid |
| GB/T 24721.5-2009 | 公路用玻璃纖維增強塑料產品 第5部分：標志底板 | Glass fiber reinforced plastic product for highway - Part 5: Sign base panel |
| GB/T 2546.1-2006 | 塑料聚丙烯（PP〕模塑和擠出材料第1部分：命名系統和分類基礎 | Plastics―Polypropylene(PP) moulding and extrusion materials―Part 1: Designation system and basis for specifications |
| GB/T 2546.2-2003 | 塑料聚丙烯(PP)模塑和擠出材料第2部分: 試樣制備和性能測定 | Plastics--Polypropylene(PP) moulding and extrusion materials--Part 2: Preparation of test specimens and determination of properties |
| GB/T 2547-2008 | 塑料 取樣方法 | Plastic resins - Sampling |
| GB/T 2572-2005 | 纖維增強塑料平均線膨脹系數試驗方法 | Fiber-reiforced plastics composites-Determination for mean coefficient of linear expansion |
| GB/T 2573-2008 | 玻璃纖維增強塑料老化性能試驗方法 | Test method for aging properties of glass fiber reinforced plastics |
| GB/T 2576-2005 | 纖維增強塑料樹脂不可溶分含量試驗方法 | Test method for insoluble matter content of resin rsed in fiber reinforced plastics |
| GB/T 2577-2005 | 玻璃纖維增強塑料樹脂含量試驗方法 | Test method for resin content of glass fiber reinforced plastics |
| GB/T 2895-2008 | 塑料 聚酯樹脂 部分酸值和總酸值的測定 | Plastics polyester resin - Determination of partial acid value and total acid value |
| GB/T 2913-1982 | 塑料白度試驗方法 | Test for whiteness of plastics |
| GB/T 2914-2008 | 塑料 氯乙烯均聚和共聚樹脂 揮發物(包括水)的測定 | Plastics - Homopolymer and copolymer resins of vinyl chloride - Determination of volatile matter (including water) |
| GB/T 2916-2007 | 塑料 氯乙烯均聚和共聚樹脂 用空氣噴射篩裝置的篩分析 | Plastic - Vinyl chloride homopolymer and copolymer resins - Sieve analysis using air-jet sieve apparatus |
| GB/T 2918-1998 | 塑料試樣狀態調節和試驗的標準環境 | Plastics--Standard atmospheres for conditioning and testing |
| GB/T 3139-2005 | 纖維增強塑料導熱系數試驗方法 | Fiber-reinforced plastics composites-Determination of thermal conductivity |
| GB/T 3140-2005 | 纖維增強塑料平均比熱容試驗方法 | Fiber-reinforced plastics composites-Determination of mean specific heat capacity |
| GB/T 3354-1999 | 定向纖維增強塑料拉伸性能試驗方法 | Test method for tensile properties oforiented fiber reinforced plastics |
| GB/T 3355-2005 | 纖維增強塑料縱橫剪切試驗方法 | Test method for longitudinal transverse shear(L-T shear)properties of fiber reinforced plastics |
| GB/T 3356-1999 | 單向纖維增強塑料彎曲性能試驗方法 | Test method for flexural properties of unidirectional fiber reinforced plastics |
| GB/T 3365-2008 | 碳纖維增強塑料孔隙含量和纖維體積含量試驗方法 | Carbon fiber reinforced plastics - Determination of void content and fiber volume content |
| GB/T 3398.1-2008 | 塑料 硬度測定 第1部分：球壓痕法 | Plastics - Determination of hardness - Part 1: Ball indentation method |
| GB/T 3398.2-2008 | 塑料 硬度測定 第2部分：洛氏硬度 | Plastics - Determination of hardness - Part 2:Rockwell hardness |
| GB/T 3399-1982 | 塑料導熱系數試驗方法護熱平板法 | Test method for thermal conductivity of plastics by means of the guarded hot plate |
| GB/T 3400-2002 | 塑料通用型氯乙烯均聚和共聚樹脂室溫下增塑劑吸收量的測定 | Plastics--Homopolymer and copolymer resins of vinyl chloeride for general use--Determination of plasticizer absorption at room temperature |
| GB/T 3402.1-2005 | 塑料氯乙烯均聚和共聚樹脂第1部分：命名體系和規范基礎 | Plastics Homopolymer and copolymer resins of vinyl chloride -- Part 1: Designation system and basis for specifiations |
| GB/T 3403.1-2008 | 塑料 粉狀脲-甲醛和脲/三聚氰胺-甲醛模塑料（UF-和UF/MF-PMCs） 第1部分： 命名系統和分類基礎 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds（UF-and UF/MF-PMCs）- Part 1: Designation system and basis for specifications |
| GB/T 3681-2000 | 塑料大氣暴露試驗方法 | Plastics--Test method of exposure to weathering |
| GB/T 3682-2000 | 熱塑性塑料熔體質量流動速率和熔體體積流動速率的測定 | Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| GB/T 3807-1994 | 聚氯乙烯微孔塑料拖鞋 | Polyvinyl chloride cellular plastic slippers |
| GB/T 3854-2005 | 增強塑料巴柯?tīng)栍捕仍囼?yàn)方法 | Test method for hardness of reinforced plastics by means of a Barcol impresser |
| GB/T 3855-2005 | 碳纖維增強塑料樹脂含量試驗方法 | Test method for resin content of carbon fiber reinforced plastics |
| GB/T 3856-2005 | 單向纖維增強塑料平板壓縮性能試驗方法 | Test method for compression properties of unidirectional fiber reinforced plastics |
| GB/T 3857-2005 | 玻璃纖維增強熱固性塑料耐化學介質性能試驗方法 | Test method for chemical resistance of glass fiber reinforced thermosetting plastics |
| GB/T 3960-1983 | 塑料滑動摩擦磨損試驗方法 | Test method for friction and wear of plasticsby sliding |
| GB/T 3961-2009 | 纖維增強塑料術語 | Terms for fibre reinforced plastics |
| GB/T 4169.1-2006 | 塑料注射模零件 第1部分：推桿 | Components of injection moulds for plastics - Part 1: Ejector pin |
| GB/T 4169.10-2006 | 塑料注射模零件 第10部分：支承柱 | Components of injection moulds for plastics - Part 10: Support pillar |
| GB/T 4169.11-2006 | 塑料注射模零件 第11部分：圓形定位元件 | Components of injection moulds for plastics - Part 11: Round locating element |
| GB/T 4169.12-2006 | 塑料注射模零件 第12部分：推板導套 | Components of injection moulds for plastics - Part 12: Ejector guide bush |
| GB/T 4169.13-2006 | 塑料注射模零件 第13部分：復位桿 | Components of injection moulds for plastics ― Part 13: Return pin |
| GB/T 4169.14-2006 | 塑料注射模零件 第14部分：推板導柱 | Components of injection moulds for plastics - Part 14: Ejector guide pillar |
| GB/T 4169.15-2006 | 塑料注射模零件 第15部分: 扁推桿 | Components of injection moulds for plastics - Part 15: Flat ejector pin |
| GB/T 4169.16-2006 | 塑料注射模零件 第16部分: 帶肩推桿 | Components of injection moulds for plastics - Part 16: Shouldered ejector pin |
| GB/T 4169.17-2006 | 塑料注射模零件 第17部分: 推管 | Components of injection moulds for plastics - Part 17: Ejector sleeve |
| GB/T 4169.18-2006 | 塑料注射模零件 第18部分: 定位圈 | Components of injection moulds for plastics - Part 18: Locating ring |
| GB/T 4169.19-2006 | 塑料注射模零件 第19部分: 澆口套 | Components of injection moulds for plastics - Part 19: Sprue bush |
| GB/T 4169.2-2006 | 塑料注射模零件 第2部分：直導套 | Components of injection moulds for plastics - Part 2: Straight guide bush |
| GB/T 4169.20-2006 | 塑料注射模零件 第20部分: 拉桿導柱 | Components of injection moulds for plastics - Part 20: Limit pin |
| GB/T 4169.21-2006 | 塑料注射模零件 第21部分: 矩形定位元件 | Components of injection moulds for plastics - Part 21: Rectangular locating element |
| GB/T 4169.22-2006 | 塑料注射模零件 第22部分: 圓形拉模扣 | Components of injection moulds for plastics - Part 22: Round mould opening delayer |
| GB/T 4169.23-2006 | 塑料注射模零件 第23部分: 矩形拉模扣 | Components of injection moulds for plastics - Part 23: Rectangular mould opening delayer |
| GB/T 4169.3-2006 | 塑料注射模零件 第3部分：帶頭導套 | Components of injection moulds for plastics - Part 3: Headed guide bush |
| GB/T 4169.4-2006 | 塑料注射模零件 第4部分：帶頭導柱 | Components of injection moulds for plastics - Part 4: Headed guide pillar |
| GB/T 4169.5-2006 | 塑料注射模零件 第5部分：帶肩導柱 | Components of injection moulds for plastics - Part 5: Shouldered guide pillar |
| GB/T 4169.6-2006 | 塑料注射模零件 第6部分：墊塊 | Components of injection moulds for plastics - Part 6: Spacer block |
| GB/T 4169.7-2006 | 塑料注射模零件 第7部分：推板 | Components of injection moulds for plastics - Part 7: Ejector plate |
| GB/T 4169.8-2006 | 塑料注射模零件 第8部分：模板 | Components of injection moulds for plastics ― Part 8:Mould plate |
| GB/T 4169.9-2006 | 塑料注射模零件 第9部分：限位釘 | Components of injection moulds for plastics - Part 9: Stop pin |
| GB/T 4170-2006 | 塑料注射模零件技術條件 | Specification of components of injection moulds for plastics |
| GB/T 4217-2008 | 流體輸送用熱塑性塑料管材 公稱外徑和公稱壓力 | Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures |
| GB/T 4550-2005 | 試驗用單向纖維增強塑料平板的制備 | Preparation of unidirection or ientated fiber reinforced plastic plates for test purposes |
| GB/T 4610-2008 | 塑料 熱空氣爐法點著溫度的測定 | Plastics - Determination of ignition temperature using a hot-air furnace |
| GB/T 4612-2008 | 塑料 環氧化合物 環氧當量的測定 | Plastics - Epoxy compounds - Determination of epoxy equivalent |
| GB/T 4616-2008 | 塑料 酚醛模塑料 丙酮可溶物（未模塑態材料的表觀樹脂含量）測定 | Plastics - Phenolic moulding materials - Determination of acetone-soluble matter（apparent resin content of material in the unmoulded state） |
| GB/T 4617-2009 | 塑料 酚醛模塑制品 丙酮可溶物的測定 | Plastics - Phenolic mouldings - Determination of acetone-soluble matter |
| GB/T 4618.1-2008 | 塑料 環氧樹脂氯含量的測定 第1部分：無機氯 | Plastics - Epoxy resins - Determination of chlorine content - Part 1: Inorganic chlorine |
| GB/T 4618.2-2008 | 塑料 環氧樹脂氯含量的測定 第2部分：易皂化氯 | Plastics - Epoxy resins - Determination of chlorine content - Part 2: Easily saponifiabLe chlorine |
| GB/T 4944-2005 | 玻璃纖維增強塑料層合板層間拉伸強度試驗方法 | Test method for interlaminar tensile strength of glass fiber reinforced plastic laminates |
| GB/T 5258-2008 | 纖維增強塑料面內壓縮性能試驗方法 | Fiber-reinforced plastic composites - Determination of compressive properties in the in-plane direction |
| GB/T 5349-2005 | 纖維增強熱固性塑料管軸向拉伸性能試驗方法 | Fiber-reinforced thermosetting plastic composites pipe-Determination of longitudinal tensile properties |
| GB/T 5350-2005 | 纖維增強熱固性塑料管軸向壓縮性能試驗方法 | Fiber-reinforced thermosetting plastic composites pipe-Determination for longitudinal compressive properties |
| GB/T 5351-2005 | 纖維增強熱固性塑料管短時水壓失效壓力試驗方法 | Fiber-reinforced thermosetting plastic composites pipe-Determination of short-time hydraulic failure pressure |
| GB/T 5352-2005 | 纖維增強熱固性塑料管平行板外載性能試驗方法 | Fiber-reinforced thermosetting plastic composites pipe-Determination for external loading properties by parallel-plate loading |
| GB/T 5470-2008 | 塑料 沖擊法脆化溫度的測定 | Plastics - Determination of the brittleness temperature by impact |
| GB/T 5471-2008 | 塑料 熱固性塑料試樣的壓塑 | Plastics - Compression moulding of test specimens of thermosetting materials |
| GB/T 5478-2008 | 塑料 滾動磨損試驗方法 | Plastics - Test method for wear by rolling |
| GB/T 5563-2006 | 橡膠和塑料軟管及軟管組合件 靜液壓試驗方法 | Rubber and plastics hoses and hose assemblies - Hydrostatic testing |
| GB/T 5564-2006 | 橡膠及塑料軟管 低溫曲撓試驗 | Rubber and plastics hoses - Subambient temperature flexibility tests |
| GB/T 5565-2006 | 橡膠或塑料增強軟管和非增強軟管 彎曲試驗 | Rubber or plastics hoses tubing - Bending tests |
| GB/T 5566-2003 | 橡膠或塑料軟管耐壓扁試驗方法 | Rubber or plastics hoses--Test method for crush resistance |
| GB/T 5567-2006 | 橡膠和塑料軟管及軟管組合件 耐吸扁性能的測定 | Rubber and plastics hoses and hose assemblies - Determination of suction resistance |
| GB/T 5568-2006 | 橡膠或塑料軟管及軟管組合件 無撓曲液壓脈沖試驗 | Rubber or plastics hoses and hose assemblies - Hydraulic impulse test without flexing |
| GB/T 5737-1995 | 食品塑料周轉箱 | Plastic container for food |
| GB/T 5738-1995 | 瓶裝酒、飲料塑料周轉箱 | Plastic crates for beverage bottled |
| GB/T 6011-2005 | 纖維增強塑料燃燒性能試驗方法熾熱棒法 | Test method for flammability characteristics of fiber-reinforced plastics-Incandescent rod method |
| GB/T 6111-2003 | 流體輸送用熱塑性塑料管材耐內壓試驗方法 | Thermoplastics pipes for the conveyance of fluids--Resistance to internal pressure--Test method |
| GB/T 6342-1996 | 泡沫塑料與橡膠線性尺寸的測定 | Cellular plastics and rubbers--Determination of linear dimensions |
| GB/T 6343-2009 | 泡沫塑料及橡膠 表觀密度的測定 | Cellular plastics and rubbers - Determination of apparent density |
| GB/T 6594.2-2003 | 塑料聚苯乙烯(PS)模塑和擠出材料第2部分: 試樣制備和性能測定 | Plastics--Polystyrene(PS) moulding and extrusion materials--Part 2: Preparation of testspecimens and determination of properties |
| GB/T 6671-2001 | 熱塑性塑料管材縱向回縮率的測定 | Thermoplastics pipes--Determination of longitudinal reversion |
| GB/T 6672-2001 | 塑料薄膜和薄片厚度測定機械測量法 | Plastics film and sheeting--Determination of thickness by mechanical scanning |
| GB/T 6673-2001 | 塑料薄膜和薄片長度和寬度的測定 | Plastics film and sheeting--Determination of length and width |
| GB/T 6743-2008 | 塑料用聚酯樹脂、色漆和清漆用漆基 部分酸值和總酸值的測定 | Plastics(polyester resins) and paints and varnishes(binders) - Determination of partial acid value and total acid value |
| GB/T 7129-2001 | 橡膠或塑料軟管容積膨脹的測定 | Rubber or plastics hoses--Determinationof volumetric expansion |
| GB/T 7139-2002 | 塑料氯乙烯均聚物和共聚物氯含量的測定 | Plastics--Vinyl chloride homopolymers and copolymers--Determination of chlorine content |
| GB/T 7141-2008 | 塑料熱老化試驗方法 | Plastics - Methods of heat aging |
| GB/T 7142-2002 | 塑料長期熱暴露后時間-溫度極限的測定 | Determination of time-temperature limits for plastics after prolonged exposure to heat |
| GB/T 7190.1-2008 | 玻璃纖維增強塑料冷卻塔 第1部分: 中小型玻璃纖維增強塑料冷卻塔 | Glass fiber reinforced plastic cooling tower - Part 1: Middle and small glass fiber reinforced plastic cooling tower |
| GB/T 7190.2-2008 | 玻璃纖維增強塑料冷卻塔 第2部分: 大型玻璃纖維增強塑料冷卻塔 | Glass fiber reinforced plastic cooling tower - Part 2: Large glass fiber reinforced plastic cooling tower |
| GB/T 7528-2002 | 橡膠和塑料軟管及軟管組合件術語 | Rubber and plastics hoses and hose assemblies--Vocabulary |
| GB/T 7530-1998 | 橡膠或塑料涂覆織物術語 | Rubber or plastics-coated fabrics--Glossary of terms |
| GB/T 7559-2005 | 纖維增強塑料層合板螺栓連接擠壓強度試驗方法 | Test method for bearing strength by bolted joints of fiber reinforced plastics laminates |
| GB/T 7948-1987 | 塑料軸承極限PV試驗方法 | Test method for PV limit of plastics bearings |
| GB/T 7984-2001 | 輸送帶具有橡膠或塑料覆蓋層的普通用途織物芯輸送帶 | Conveyor belts--Specification for rubber or plastics covered conveyor belts of textile constructionfor general use |
| GB/T 8237-2005 | 纖維增強塑料用液體不飽和聚酯樹脂 | Liquid unsaturated polyester resin for fiber reinforced plastics |
| GB/T 8323.1-2008 | 塑料 煙生成 第1部分：煙密度試驗方法導則 | Plastic - Smoke generation - Part 1: Guidance on optical-density testing |
| GB/T 8323.2-2008 | 塑料 煙生成 第2部分：?jiǎn)问曳y(cè)定煙密度試驗方法 | Plastic - Smoke generation - Part 2: Determination of optical density by a single-chamber test |
| GB/T 8324-2008 | 塑料 模塑材料體積系數的測定 | Plastics - Determination of bulk factor of moulding materials |
| GB/T 8332-2008 | 泡沫塑料燃燒性能試驗方法 水平燃燒法 | Test method for flammability of cellular plastic - Horizonal burning method |
| GB/T 8333-2008 | 硬質泡沫塑料燃燒性能試驗方法 垂直燃燒法 | Test method for flammability of rigid cellular plastic - Virtical burning method |
| GB/T 840-1988 | 塑料滾花頭螺釘 | Plastic diamond knurlhead screws |
| GB/T 8661-2008 | 塑料 苯乙烯-丙烯腈共聚物殘留丙烯腈單體含量的測定 氣相色譜法 | Plastics - Styrene/acrylonitrile copolymers - Determination of residual acrylonitrile monomer content - Gas chromatography method |
| GB/T 8802-2001 | 熱塑性塑料管材、管件維卡軟化溫度的測定 | Thermoplastics pipes and fitting--Determination of vicat softening temperature |
| GB/T 8804.1-2003 | 熱塑性塑料管材拉伸性能測定第1部分:試驗方法總則 | Thermoplastic pipes--Determination of tensile properties--Part 1: General test method |
| GB/T 8804.2-2003 | 熱塑性塑料管材拉伸性能測定第2部分: 硬聚氯乙烯(PVC-U)、氯化聚氯乙烯(PVC-C)和高抗沖聚氯乙烯(PVC-HI)管 | Thermoplastic pipes--Determination of tensile properties--Part 2: Pipes made of unplasticized poly(vinyl chloride)(PVC-U)，chlorinated poly(vinyl chloride)(PVC-C)and high-impact poly(vinyl chloride)(PVC-HI) |
| GB/T 8804.3-2003 | 熱塑性塑料管材拉伸性能測定第3部分: 聚烯烴管材 | Thermoplastic pipes--Determination of tensile properties--Part 3: Polyolefin pipes |
| GB/T 8806-2008 | 塑料管道系統 塑料部件尺寸的測定 | Plastics piping systems - Plastics components - Determination of dimensions |
| GB/T 8807-1988 | 塑料鏡面光澤試驗方法 | Test method for specular gloss of plastics |
| GB/T 8808-1988 | 軟質復合塑料材料剝離試驗方法 | Test method for peel force of flexible laminated plastics |
| GB/T 8809-1988 | 塑料薄膜抗擺錘沖擊試驗方法 | Test method for pendulum impact resistance of plastic films |
| GB/T 8810-2005 | 硬質泡沫塑料吸水率的測定 | Determination of water absorption of rigid cellular plastics |
| GB/T 8811-2008 | 硬質泡沫塑料 尺寸穩定性試驗方法 | Test method for dimensional stability of rigid cellular plastics |
| GB/T 8812.1-2007 | 硬質泡沫塑料 彎曲性能的測定 第1部分：基本彎曲試驗 | Rigid cellular plastics - Determination of flexural properties - Part 1: Basic bending test |
| GB/T 8812.2-2007 | 硬質泡沫塑料 彎曲性能的測定 第2部分: 彎曲強度和表觀彎曲彈性模量的測定 | Rigid cellular plastics - Determination of flexural properties - Part 2: Determination of flexural strength and apparent flexural modulus of elasticity |
| GB/T 8813-2008 | 硬質泡沫塑料壓縮性能的測定 | Rigid cellular plastics - Determination of compression properties |
| GB/T 8815-2008 | 電線電纜用軟聚氯乙烯塑料 | Plasticized polyvinyl chloride （PVC）compounds for wire and cable |
| GB/T 8846-2005 | 塑料成型模術語 | Terminology of moulds for plastics |
| GB/T 8924-2005 | 纖維增強塑料燃燒性能試驗方法氧指數法 | Test method for flammability characteristics of fiber reinforced plastics-Oxygen index method |
| GB/T 8946-1998 | 塑料編織袋 | Plastic woven sack |
| GB/T 8947-1998 | 復合塑料編織袋 | Composite plastic woven sack |
| GB/T 9267-2008 | 涂料用乳液和涂料、塑料用聚合物分散體 白點溫度和最低成膜溫度的測定 | Emulsions for coatings and polymer dispersions for coatings and plastics - Determination of white point temperature and minimum film-forming temperature |
| GB/T 9330.1-2008 | 塑料絕緣控制電纜 第1部分：一般規定 | Plastic insulated control cables - Part 1: General requirements |
| GB/T 9330.2-2008 | 塑料絕緣控制電纜 第2部分：聚氯乙烯絕緣和護套控制電纜 | Plastic insulated control cables - Part 2：Polyvinyl chloride insulated and sheathed control cables |
| GB/T 9330.3-2008 | 塑料絕緣控制電纜 第3部分：交聯聚乙烯絕緣控制電纜 | Plastic insulated control cables - Part 3: Cross-linked polyethylene insulated control cables |
| GB/T 9341-2008 | 塑料 彎曲性能的測定 | Plastics - Determination of flexural properties |
| GB/T 9343-2008 | 塑料燃燒性能試驗方法 閃燃溫度和自燃溫度的測定 | Test method for flammability of plastics - Determination of flash-ignition temperature and self-ignition temperature |
| GB/T 9345.1-2008 | 塑料 灰分的測定 第1部分：通用方法 | Plastics - Determination of ash - Part 1: General methods |
| GB/T 9345.2-2008 | 塑料 灰分的測定 第2部分：聚對苯二甲酸烷撐酯 | Plastics - Determination of ash - Part 2: Poly(alkylend terephthalate)materials |
| GB/T 9345.4-2008 | 塑料 灰分的測定 第4部分：聚酰胺 | Plastics - Determination of ash - Part 4: Polyamides |
| GB/T 9348-2008 | 塑料 聚氯乙烯樹脂 雜質與外來粒子數的測定 | Plastics - Poly(vinyl chloride) resins - Determination of number of impurities and foreign particles |
| GB/T 9350-2003 | 塑料氯乙烯均聚和共聚樹脂水萃取液pH值的測定 | Plastics--Homopolymer andcopolymer resins of vinyl chloride--Determination of pH of aqueous extract |
| GB/T 9352-2008 | 塑料 熱塑性塑料材料試樣的壓塑 | Plastic - Compression moulding of test specimens of thermoplastic materials |
| GB/T 9572-2001 | 橡膠和塑料軟管及軟管組合件電阻的測定 | Rubber and plastics hoses and hose assemblies--Determination of electrical resistance |
| GB/T 9573-2003 | 橡膠、塑料軟管及軟管組合件尺寸測量方法 | Rubber and plastics hose and hose assemblies--Methods of measurement of dimensions |
| GB/T 9574-2001 | 橡膠和塑料軟管及軟管組合件試驗壓力、爆破壓力與設計工作壓力的比率 | Rubber and plastics hoses and hose assemblies--Ratios of proof and burst pressure to design working pressure |
| GB/T 9575-2003 | 工業通用橡膠和塑料軟管內徑尺寸及公差和長度公差 | Rubber and plastics hoses for general-purpose industrial applications--Bore diameters and tolerances，and tolerances on length |
| GB/T 9576-2001 | 橡膠和塑料軟管及軟管組合件選擇、貯存、使用和維護指南 | Rubber and plastics hose and hose assemblies--Guide to selection，use，and maintenance |
| GB/T 9577-2001 | 橡膠和塑料軟管及軟管組合件標志、包裝和運輸規則 | Rubber and plastics hose and hose assemblies--Rules for marking，package and transportation |
| GB/T 9639.1-2008 | 塑料薄膜和薄片 抗沖擊性能試驗方法 自由落鏢法 第1部分：梯級法 | Plastics film and sheeting - Determination of impact resistance by the free-falling dart methord - Part 1: Staircase methords |
| GB/T 9641-1988 | 硬質泡沫塑料拉伸性能試驗方法 | Test method for tensile properties of rigid cellular plastics |
| GB/T 9647-2003 | 熱塑性塑料管材環剛度的測定 | Thermoplastics pipes--Determination of ringstiffness |
| GB/T 9900-2008 | 橡膠或塑料涂覆織物 導風筒 | Rubber - or plastics-coated fabrics - Ventilation ducting |
| GB/T 9979-2005 | 纖維增強塑料高低溫力學性能試驗準則 | Guide rule of test for mechanical properties of fiber-reinforced plastics at elevated and reduced temperatures |
| GB/Z 22074-2008 | 塑料外殼式斷路器可靠性試驗方法 | Reliability test method for moulded case circuit-breakers |
| HD 21.1 S4-2002 | 額定電壓為450/750V及以下的熱塑性塑料絕的電纜 第1部分：一般要求 | Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation - Part 1: General requirements |
| HD 21.14 S1-2003 | 額定電壓450/750V及以下的熱塑性塑料絕的電纜 第14部分：非鹵素?zé)崴苄运芰匣衔锏慕^緣和包覆的軟電纜(軟 | Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation - Part 14: Flexible cables (cords), insulated and sheathed with halogen-free thermoplastic compounds |
| HG 2-162-1965 | 塑料低溫沖擊壓縮試驗方法 | () |
| HG 2-163-1965 | 塑料薄膜低溫伸長試驗方法 | () |
| HG/T 2-163-1965(1982) | 塑料低溫伸長試驗方法 | () |
| HG/T 20640-1997(2009) | 塑料設備 | () |
| HG/T 2106-1991 | 耐酸酚醛塑料 耐酸度的測量 | () |
| HG/T 2107-1991 | 耐酸酚醛塑料 丙酮可溶物的測定 | () |
| HG/T 2128-2009 | 改性酚醛玻璃纖維增強塑料管技術條件 | Specifications for pipe of modified phenolic glass fiber reinforced plastics |
| HG/T 2129-1991 | 耐酸酚醛塑料制化工設備零部件 | () |
| HG/T 2129-2009 | 改性酚醛玻璃纖維增強塑料管件技術條件 | Specifications for pipe fitting of modified phenolic glass fiber reinforced plastics |
| HG/T 2150-2009 | 橡膠塑料壓延機檢測方法 | Measuring method of rubber calenders & plastics calenders |
| HG/T 21557.3-2006 | 塑料階梯環填料 | Plastic cascade ring packing |
| HG/T 2232-1991 | 改性聚苯醚工程塑料 | () |
| HG/T 22807-1997 | 化工礦山塑料管道工程設計規范 | () |
| HG/T 2300-1992 | 織物增強可折疊式通用輸水塑料軟管 | () |
| HG/T 2301-2008 | 壓縮空氣用織物增強熱塑性塑料軟管 | () |
| HG/T 2437-2006 | 塑料襯里復合鋼管和管件 | Steel pipes and fitting lined with plastic |
| HG/T 2440-1993 | 橡膠或塑料涂覆織物屈撓磨損試驗機技術條件 | () |
| HG/T 2577-2006 | 橡膠或塑料提升帶 | Rubber and plastics belting for use on bucket elevators |
| HG/T 2580-2008 | 橡膠或塑料涂覆織物 拉伸強度和拉斷伸長率的測定 | () |
| HG/T 2581.1-2009 | 橡膠或塑料涂覆織物 耐撕裂性能的測定 第1部分：恒速撕裂法 | Rubber-or plastics-coated fabrics-Determination of tear resistance-Part 1:constant rate of tear methods |
| HG/T 2581.2-2009 | 橡膠或塑料涂覆織物 耐撕裂性能的測定 第2部分：沖擊擺錘法 | Rubber-or plastics-coated fabrics-Determination of tear resistance-Part 2:Ballistic pendulum method |
| HG/T 2582-2008 | 橡膠或塑料涂覆織物 耐水滲透性能的測定 | () |
| HG/T 2715-1995(2009) | 橡膠或塑料涂覆織物 抗粘合性的測定 | () |
| HG/T 2716-2008 | 橡膠或塑料涂覆織物 靜態耐臭氧龜裂性能的測定 | () |
| HG/T 2718-1995(2009) | 汽車空調用橡膠和塑料軟管及軟管組合件 | () |
| HG/T 2799-1996 | 吸引和低壓排輸石油液體用塑料軟管 | () |
| HG/T 2867-1997(2009) | 橡膠或塑料涂覆織物調節和試驗的標準環境 | () |
| HG/T 2869-1997(2009) | 橡膠和塑料軟管 靜態條件下耐臭氧性能的評價 | () |
| HG/T 3037-2008 | 計量分配燃油用橡膠和塑料軟管及軟管組合件 | () |
| HG/T 3045-2008 | 排吸用螺旋線增強的熱塑性塑料軟管 | () |
| HG/T 3047-2004 | 橡膠或塑料涂覆織物 透氣性的測定 | () |
| HG/T 3048-2009 | 橡膠或塑料涂覆織物 耐組合剪切曲撓和磨擦性能的測定 | Rubber-or plastics-coated fabrics-Determination of resistance to combined shear flexing and rubbing |
| HG/T 3049-1999(2009) | 橡膠或塑料涂覆織物 加速老化試驗 | () |
| HG/T 3050.1-2001(2009) | 橡膠或塑料涂覆織物整卷特性的測定 第一部分：測定長度、寬度和凈質量的方法 | () |
| HG/T 3050.2-2001(2009) | 橡膠或塑料涂覆織物整卷特性的測定 第二部分：測定單位面積的總質量、單位面積的涂覆質量和單位面積底布質 | () |
| HG/T 3050.3-2001(2009) | 橡膠或塑料涂覆織物整卷特性的測定 第三部分：測定厚度的方法 | () |
| HG/T 3052-2008 | 橡膠或塑料涂覆織物 涂覆層粘合強度的測定 | () |
| HG/T 3053-1999(2009) | 橡膠或塑料涂覆織物 柔軟性的測定 扁環法 | () |
| HG/T 3077-1999(2009) | 橡膠、塑料輥硬度要求 | () |
| HG/T 3078-2001(2009) | 橡膠、塑料輥 表面特性 | () |
| HG/T 3079-1999(2009) | 橡膠、塑料輥尺寸公差 | () |
| HG/T 3120-1998(2009) | 橡膠塑料機械外觀通用技術條件 | () |
| HG/T 3183-1989 | 氟塑料襯里單級單吸化工離心泵技術條件 | () |
| HG/T 3228-2001(2009) | 橡膠塑料機械涂漆通用技術條件 | () |
| HG/T 3249.3-2008 | 塑料工業用重質碳酸鈣 | () |
| HG/T 3690-2001 | 工業用鋼骨架聚乙稀塑料復合管 | () |
| HG/T 3691-2001 | 工業用鋼骨架聚乙稀塑料復合管件 | () |
| HG/T 3704-2003(2009) | 氟塑料襯里閥門通用技術條件 | () |
| HG/T 3732-2004 | 改性酚醛玻璃纖維增強塑料球閥技術條件 | () |
| HG/T 3839-2006 | 塑料剪切強度試驗方法 穿孔法 | () |
| HG/T 3840-2006 | 塑料彎曲性能小試樣試驗方法 | () |
| HG/T 3841-2006 | 塑料沖擊性能小試樣試驗方法 | () |
| HG/T 3842-2006 | 消防用不可折疊型橡膠和塑料軟管 第1部分:定位應急設施用軸卷半硬性軟管 | () |
| HG/T 3862-2006 | 塑料黃色指數試驗方法 | () |
| HG/T 3865-2006 | 熱固性模塑料矩道流動固化性試驗方法 | () |
| HG/T 3915-2006 | 氟塑料襯里反應釜 | Reacting caldron lined with fluoroplastics |
| HG/T 3986-2007 | 塑料塔填料技術條件 | Specification for plastic tower packing |
| HG/T 4087-2009 | 塑料合金防腐蝕復合管 | Anticorrosion plastic alloy composite pipe |
| HG/T 4088-2009 | 塑料襯里設備 通用技術條件 | General Technical Specification for equipments lined with plastics |
| HG/T 4089-2009 | 塑料襯里設備 水壓試驗方法 | Hydrostatic pressure test method for equipments lined with plastics |
| HG/T 4090-2009 | 塑料襯里設備 電火花試驗方法 | Spark test method for equipments lined with plastics |
| HG/T 4091-2009 | 塑料襯里設備 耐溫試驗方法 | Temperature test method for equipments lined with plastics |
| HG/T 4092-2009 | 塑料襯里設備 熱脹冷縮試驗方法 | Expansion and contraction test method for equipments lined with plastics |
| HG/T 4093-2009 | 塑料襯里設備 襯里耐負壓試驗方法 | Vacuum test method for equipments lined with plastics |
| HG/T 4112-2009 | 塑料襯里儲槽和罐式容器技術條件 | Plastic lining storage tand and pot type vessel engineering factor |
| JB/T 10180-2000 | 水輪發電機推力軸承彈性金屬塑料瓦技術條件 | () |
| JB/T 10190-2010 | 滾動軸承 包裝用塑料筒 | Rolling bearings-Plastic cylinders for packaging |
| JB/T 10342-2002 | 塑料擠出異型材輔機 | () |
| JB/T 10359-2002 | 空調器室外機用塑料環境技術要求 | () |
| JB/T 10464-2004 | 拉條式塑料切粒機 | () |
| JB/T 10594-2006 | 日光溫室和塑料大棚結構與性能要求 | () |
| JB/T 10636-2006 | 額定電壓0.6/1kV(Um = 1.2kV)銅芯塑料絕緣預制分支電纜 | Copper-conductor extruded plastic insulated cables with pre-fabricated branches for rated voltage of 0.6/1kV(Um=1.2kV) |
| JB/T 10706-2007 | 機械密封用氟塑料全包覆橡膠Ｏ形圈 | () |
| JB/T 10867-2008 | 輸送用塑料平頂鏈和鏈輪 | () |
| JB/T 10898-2008 | 塑料擠出復合膜輔機 | () |
| JB/T 10899-2008 | 塑料擠出雙壁波紋管輔機 | () |
| JB/T 10981-2010 | 玻璃纖維增強塑料軸流通風機 | Glass fiber reinforced plastic axial fans |
| JB/T 10994-2010 | 纏繞式礦井提升設備用塑料襯板 | Plastic lining for winding mine hoist |
| JB/T 20065.1～5-2005 | 塑料瓶瓶裝聯動線 | () |
| JB/T 20066-2005 | 易折塑料瓶口服液劑灌裝機 | Easy-folding plastic-bottle oral liquid filling & sealing machine |
| JB/T 20095-2007 | 塑料輸液瓶灌封聯動機 | () |
| JB/T 2171-1999 | 額定電壓450/750V及以下農用直埋鋁芯塑料絕緣塑料護套電線 | () |
| JB/T 2485-1978 | 橡膠塑料機械 產品型號編制方法 | () |
| JB/T 2627-2008 | 塑料擠出硬管輔機 | () |
| JB/T 3199-1994 | 熱固性塑料水潤滑耐磨材料 | () |
| JB/T 3275-2001 | 圓盤真空過濾機用塑料扇形濾板 | () |
| JB/T 3820-1984 | 塑料制品液壓機 精度 | () |
| JB/T 3958.1-1999 | 電氣絕緣用熱固性模塑料 一般要求 | () |
| JB/T 3958.2-1999 | 電氣絕緣用熱固性模塑料 試驗方法 | () |
| JB/T 4278.1-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 總則 | () |
| JB/T 4278.10-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 火花試驗機 | () |
| JB/T 4278.2-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 低溫沖擊試驗裝置 | () |
| JB/T 4278.3-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 曲撓試驗裝置 | () |
| JB/T 4278.4-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 耐磨試驗裝置 | () |
| JB/T 4278.5-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 單根電線電纜垂直燃燒DZ-1 法試驗裝置 | () |
| JB/T 4278.6-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 自然通風熱老化試驗箱 | () |
| JB/T 4278.7-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 恒溫水槽 | () |
| JB/T 4278.8-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 低溫試驗箱 | () |
| JB/T 4278.9-1993 | 橡皮塑料電線電纜試驗儀器設備檢定方法 氧彈、空氣彈老化試驗箱 | () |
| JB/T 5290-2008 | 塑料圓織機 | () |
| JB/T 5291-2007 | 塑料破碎機 | () |
| JB/T 5293-1991 | 可發性聚苯乙烯泡沫塑料成型機 | () |
| JB/T 5416-2005 | 塑料擠出干法熱切造粒輔機 | () |
| JB/T 5417-2007 | 塑料排氣擠出機 | () |
| JB/T 5419-2008 | 塑料擠出平膜扁絲輔機 | () |
| JB/T 5420-2001 | 通向雙螺桿塑料擠出機 | () |
| JB/T 5421-1991 | 塑料薄膜回收擠出造粒機組 | () |
| JB/T 5438-2008 | 塑料機械 術語 | () |
| JB/T 5822-1991 | 電氣絕緣用酚醛玻璃纖維模塑料 | () |
| JB/T 5985-1992 | 滑動軸承 水潤滑熱固性塑料軸承 | () |
| JB/T 6057-1992 | 塑料模具成型部分用鋼及其熱處理 技術條件 | () |
| JB/T 6067-1992 | 氣相防銹塑料薄膜 技術條件 | () |
| JB/T 6072-1992 | 塑料耐擦傷性能試驗方法 | () |
| JB/T 6162-2004 | 塑料、玻璃珠和金屬銀幕 通用工藝規范 | () |
| JB/T 6489-1999 | 塑料捏合機 | () |
| JB/T 6490-1992 | 塑料壓力成型機 | () |
| JB/T 6491-2001 | 導向雙螺桿塑料擠出機 | () |
| JB/T 6492-2001 | 錐形雙螺桿塑料擠出機 | () |
| JB/T 6493-1992 | 塑料制袋機 | () |
| JB/T 6494-2002 | 料斗式塑料干燥機 | () |
| JB/T 6542-1993 | 熱固性模塑料收縮率的測定 | () |
| JB/T 6543-1993 | 硬質塑料板平面彎曲疲勞特性試驗方法 | () |
| JB/T 6544-1993 | 塑料拉伸和彎曲彈性模量試驗方法 | () |
| JB/T 6723.2-2008 | 內燃機冷卻風扇 第2部分：塑料冷卻風扇 技術條件 | () |
| JB/T 6928-1993 | 塑料擠出帶輔機 | () |
| JB/T 6929-1993 | 塑料擠出轉盤制鞋機 | () |
| JB/T 6942-2007 | 半棚式塑料暖棚 | The plastic stall |
| JB/T 6980.1-1993 | 塑料薄膜和紙壓敏粘貼標牌 技術條件 | () |
| JB/T 6980.2-1993 | 塑料薄膜和紙壓敏粘貼標牌 試驗方法 | () |
| JB/T 7048-2002 | 滾動軸承零件 工程塑料保持架技術條件 | () |
| JB/T 7251-1994 | 塑料擠出拉絲輔機 | () |
| JB/T 7267-2004 | 塑料注射成型機 | () |
| JB/T 7409-1994 | 塑料洛氏硬度計 技術條件 | () |
| JB/T 7410-2010 | 塑料球壓痕硬度計 技術條件 | Specification for the ball indentation hardness testers of plastics |
| JB/T 7521-1994 | 塑料-青銅-鋼背三層復合自潤滑板材 | () |
| JB/T 7525-1994 | 聚丙烯 玻璃纖維增強塑料復合管和管件 | () |
| JB/T 7600.5-2008 | 電線電纜PNS型機用線盤 第5部分：塑料機用線盤 | () |
| JB/T 7669-2004 | 塑料混合機 | () |
| JB/T 7770-191995(2009) | 不飽和聚酯玻璃纖維增強模塑料 | () |
| JB/T 7797-1995 | 橡膠、塑料拉力試驗機技術條件 | () |
| JB/T 8043.1-1999 | 機床夾具零件及部件 塑料夾具用六角頭螺釘 | () |
| JB/T 8043.2-1999 | 機床夾具零件及部件 塑料夾具用內六角螺釘 | () |
| JB/T 8043.3-1999 | 機床夾具零件及部件 塑料夾具用柱塞 | () |
| JB/T 8061-1996 | 單螺桿塑料擠出機 | () |
| JB/T 8312.1-2005 | 中小型異步電機用工程塑料風扇 技術條件（機座號63～355） | () |
| JB/T 8400-1996 | 無泄漏磁力傳動塑料自吸泵 | () |
| JB/T 8458-1996 | 電氣設備輔件塑料制品一般要求和試驗方法 | () |
| JB/T 8507-1996 | 高頻塑料熱合機 | () |
| JB/T 8538-1997 | 塑料機械用螺桿、機筒 | () |
| JB/T 8539-1997 | 塑料擠出吹塑中空成型機 | () |
| JB/T 8589-2006 | 玻璃纖維增強塑料復合檢查井蓋 | () |
| JB/T 8688-1998 | 塑料離心泵 | () |
| JB/T 8698-1998 | 熱固性塑料注射成型機 | () |
| JB/T 8703-1998 | 塑料擠出吹塑薄膜輔機 | () |
| JB/T 8720-1998 | 拖拉機用熱塑性塑料零件 通用技術條件 | () |
| JB/T 8744-2008 | 塑料擠出模 術語 | () |
| JB/T 8745-2008 | 塑料異型材擠出模 技術條件 | () |
| JB/T 8746.1-2008 | 塑料異型材擠出模零件 第1部分：矩形模板 | () |
| JB/T 8746.2-2008 | 塑料異型材擠出模零件 第2部分：圓形模板 | () |
| JB/T 8746.3-2008 | 塑料異型材擠出模零件 第3部分：矩形機頸 | () |
| JB/T 8746.4-2008 | 塑料異型材擠出模零件 第4部分：圓形機頸 | () |
| JB/T 8746.5-2008 | 塑料異型材擠出模零件 第5部分：定型塊 | () |
| JB/T 8746.6-2008 | 塑料異型材擠出模零件 第6部分：型板 | () |
| JB/T 8746.7-2008 | 塑料異型材擠出模零件 第7部分：定位零件 | () |
| JB/T 8920-1999 | 工程塑料內鏈節輕型輸送鏈 | () |
| JB/T 9086-2007 | 塑料袋熱壓式封口機 | Plastic bag heating sealer |
| JB/T 9447-1999 | 靜電復印機用涂氟塑料定影輥 技術條件 | () |
| JC 586-1995 | 熱固化玻璃纖維增強塑料食品容器 | () |
| JC/T 1010-2006 | 衛星地球接收站用片狀模塑料（SMC）天線反射面 | () |
| JC/T 1027-2007 | 接觸軌玻璃纖維增強塑料防護罩 | Glass fiber reinforced plastics protective cover of contact rail |
| JC/T 1092-2008 | 纖維增強塑料機械成型用不飽和聚酯樹脂 | () |
| JC/T 349-1983(1996) | 玻璃纖維增強塑料平板拉-拉疲勞性能試驗方法 | () |
| JC/T 490-1992 | 玻璃纖維增強熱固性塑料拉擠型材的尺寸公差 | () |
| JC/T 491-1992（1996） | 增強塑料拉擠型材按組分分類的方法 | () |
| JC/T 492-1992(1996) | 火車客車用片狀模塑料(SMC)窗框 | () |
| JC/T 516-1993 | 自應力鋼筋混凝土輸水管用塑料嵌件 | () |
| JC/T 550-2008 | 聚氯乙烯塊狀塑料地板膠粘劑 | () |
| JC/T 553-1994 | 玻璃纖維增強塑料離心通風機 | () |
| JC/T 587-1995 | 纖維纏繞增強塑料貯罐 | () |
| JC/T 658.1-2007 | 玻璃纖維增強塑料水箱 第1部分：SMC組合式水箱 | Glass fiber reinforced plastics water tanks Part 1:SMC sectional water tanks |
| JC/T 658.2-1997 | 玻璃纖維增強塑料水箱 第2部分：手糊成型整體式水箱 | () |
| JC/T 692-1998 | 反滲透水處理裝置用玻璃纖維增強塑料壓力殼體 | () |
| JC/T 717-1990(1996) | 地面用玻璃纖維增強塑料壓力容器 | () |
| JC/T 764-2001 | 坐便器塑料坐圈和蓋 | () |
| JC/T 773-1982(1996) | 單向纖維增強塑料層間剪切強度試驗方法 | () |
| JC/T 779-2000 | 玻璃纖維增強塑料浴缸 | () |
| JC/T 782-1987(1996) | 玻璃纖維增強塑料透光率試驗方法 | () |
| JC/T 783-2004 | 玻璃纖維增強改性酚醛塑料球閥 | () |
| JC/T 939-2004 | 建筑用抗菌塑料管抗細菌性能 | () |
| JC/T 941-2004 | 門窗用玻璃纖維增強塑料拉擠中空型材 | () |
| JC/T 944-2005 | 彩噴片狀模塑料（SMC）瓦 | () |
| MT 141－2005 | 煤礦井下用塑料網假頂帶 | () |
| MT 181-1988(2005) | 煤礦井下用塑料管安全性能檢驗規范 | () |
| MT 558.1－2005 | 煤礦井下用塑料管材 第1部分：聚乙烯管材 | () |
| MT 558.2－2005 | 煤礦井下用塑料管材 第2部分：聚氯乙烯管材 | () |
| MT 558.3-2006 | 煤礦井下用塑料管材 第3部分：玻璃鋼管材 | () |
| MT 558.3－2005 | 煤礦井下用塑料管材 第3部分：玻璃鋼管材 | () |
| MT 756-1997(2005) | 隔爆水槽用聚苯乙烯泡沫塑料阻燃性能試驗方法 | () |
| MT 960-2005 | 煤礦井下假頂用塑料編織布 | () |
| MT/T 1061-2007 | 樹脂錨桿 玻璃纖維增強塑料桿體及附件 | () |
| MT/T 783-1998 | 沸騰爐灰渣制橡膠塑料補強填料技術條件 | () |
| QB 1110-1991 | 聚氨酸 ,聚苯工烯 ,聚乙烯泡沫塑料生產安全技術規程 | () |
| QB 1532-1992 | 塑料制品加工企業職業安全衛生設計規定 | () |
| QB 1999-1994(2009) | 密胺塑料餐具 | () |
| QB 2495-2000 | 聚氯乙烯塑料生產防塵防毒技術規程 | () |
| QB/T 1046-2003 | 凹版塑料薄膜表印油墨 | () |
| QB/T 1124-1991(2009) | 聚氯乙烯塑料鞋底 | () |
| QB/T 1129-1991(2009) | 塑料門窗-硬物撞擊試驗方法 | () |
| QB/T 1130-1991(2009) | 塑料直角撕裂性能試驗方法 | () |
| QB/T 1232-1991(2009) | 軟質聚氨脂泡沫塑料復合材料 | () |
| QB/T 1235-1991(2009) | 塑料門窗合葉(鉸鏈) | () |
| QB/T 1434-1992(2009) | 塑料擠出拉伸網 | () |
| QB/T 1647-1992(2009) | 無基材聚氯乙烯塑料卷材地板 | () |
| QB/T 1649-1992(2009) | 聚苯乙烯泡沫塑料包裝材料 | () |
| QB/T 1651-1992(2009) | 聚乙烯塑料中空板 | () |
| QB/T 1653-1992(2009) | 聚氯乙烯塑料涼鞋、拖鞋 | () |
| QB/T 1870-1993(2009) | 塑料菜板 | () |
| QB/T 2000-1994(2009) | 塑料遮陽(光)網 | () |
| QB/T 2024-1994 | 凹版復合塑料薄膜油墨 | () |
| QB/T 2080-2010 | 高回彈軟質聚氨酯泡沫塑料 | Flexible cellular polymeric materials-high-resilience polyurethane foam |
| QB/T 2081-1995(2009) | 冰箱、冰柜用硬質聚氨酯泡沫塑料 | () |
| QB/T 2309-1997(2009) | 塑料鉛筆擦 | () |
| QB/T 2358-1998(2009) | 塑料薄膜包裝袋熱合強度試驗方法 | () |
| QB/T 2411-1998(2009) | 硬質泡沫塑料水蒸氣透過性能的測定 | () |
| QB/T 2462.1-1999(2009) | 電線電纜用輻照交聯聚烯烴塑料額定電壓0～10KV聚乙烯絕緣料 | () |
| QB/T 2568-2002(2009) | 硬聚氯乙烯(PVCU)塑料管道系統用溶液劑型膠粘劑 | () |
| QB/T 2591-2003(2009) | 抗菌塑料-抗菌性能試驗方法和抗菌效果 | () |
| QB/T 2667.1-2004 | 埋地通信用多孔一體塑料管材 第1部分：硬聚氯乙烯（PVC-U）多孔一體管材 | () |
| QB/T 2667.2-2004 | 埋地通信用多孔一體塑料管材 第2部分：聚乙烯（PE）多孔一體管材 | () |
| QB/T 2669-2004 | 泡沫塑料吸水性試驗方法 | () |
| QB/T 2670-2004 | 降解塑料片材定義、分類、標志和降解性能要求 | () |
| QB/T 2671-2004 | 生物分解塑料片材定義、標志和生物分解性能要求 | () |
| QB/T 2672-2004 | 可堆肥塑料片材定義、標志和可堆肥性能要求 | () |
| QB/T 2803－2006 | 硬質塑料管材彎曲度測量方法 | () |
| QB/T 2854-2007 | 塑料土工格柵蠕變?cè)囼?yàn)和評價方法 | Creep testing and evaluating method on plastic georids |
| QB/T 2904-2007 | 自結皮硬質聚氨酯泡沫塑料 | Rigid self-skinned polyurethane cellular plastics |
| QB/T 2957-2008 | 淀粉基塑料中淀粉含量的測定 熱重法(TG) | Determination of starch content of starch based plastics |
| QB/T 3631-1999(2009) | 聚氯乙烯塑料波紋電線管 | () |
| QB/T 3650-1999 | 甲基丙烯酸甲酯共聚模塑料 | () |
| QB/T 3677-1999 | 塑料壓延設備勞動安全技術規程 | () |
| QB/T 3808-1999(2009) | 復合塑料編織布 | () |
| QB/T 3810-1999(2009) | 塑料網眼袋 | () |
| QB/T 3811-1999 | 塑料打包帶 | () |
| QB/T 4012-2010 | 淀粉基塑料 | Starch-based Plastics |
| QB/T 4049-2010 | 塑料飲水口杯 | Plastic cup for drinking |
| QB/T 6808-1999 | 復合塑料編織布 | () |
| QC/T 15-1992(2005) | 汽車塑料制品通用試驗方法 | () |
| QC/T 29017-1991(2009) | 汽車模制塑料零件未注公差尺寸的極限偏差 | () |
| QC/T 346-1999(2009) | 塑料堵塞 | () |
| QC/T 349-1999(2005) | 塑料緊箍帶 | () |
| QC/T 350-1999(2009) | 塑料開尾銷釘 | () |
| QC/T 438-1999(2005) | 汽車點火系高壓塑料件技術條件 | () |
| QC/T 614-1999(2009) | 塑料真空成型機 | () |
| QC/T 617-1999(2009) | 端封式嵌裝塑料螺母 | () |
| QC/T 618-1999(2009) | 嵌裝塑料螺母 技術條件 | () |
| QC/T 641-2005 | 汽車用塑料密封條 | Plastic weatherstrips for automobile |
| QC/T 713-2004 | 塑料（尼龍）用自攻螺釘螺紋 | () |
| QC/T 797-2008 | 汽車塑料件、橡膠件和熱塑性彈性體件的材料標識和標記 | Material identification & marking of automotive plastic,rubber & thermoplastic elastomer parts |
| QC/T 798-2008 | 汽車用多層塑料燃油管 | Multi-layers plastic tubing for automotive fuel system |
| SB/T 10179-1993 | 塑料類商品儲藏技術 | () |
| SH/T 1541-2006 | 熱塑性塑料顆粒外觀試驗方法 | () |
| SY/T 0415-1996 | 埋地鋼質管道硬質聚氨酯泡沫塑料防腐保溫層技術標準 | () |
| SY/T 0603-2005 | 玻璃纖維增強塑料儲罐規范 | () |
| SY/T 415-1996 | 埋地鋼質管道硬質聚氨酯泡沫塑料防腐保溫層技術標準 | () |
| SY/T 5736-1995 | 增強塑料抽油桿 | () |
| SY/T 5860-1993 | 塑料球投球器 | () |
| SY/T 6123-1995 | 雙層預充填塑料防砂篩管 | () |
| Tapping screws thread for plastic(nylon) | 塑料文具盒 | () |
| YB/T 094-1997(2006年確認) | 塑料模具用扁鋼 | () |
| YB/T 107-1997(2006年確認) | 塑料模具用熱軋厚鋼板 | () |
| YB/T 129-1997(2006年確認) | 塑料模具鋼模塊技術條件 | () |
| YB/T 4132-2005 | 循環流化床鍋爐用耐磨耐火可塑料 | () |
| YB/T 5115-1993 | 粘土質和高鋁質耐火可塑料 | () |
| YB/T 5116-1993(2005) | 粘土質和高鋁質耐火可塑料試樣制備方法 | () |
| YB/T 5117-1993(2005) | 粘土質和高鋁質耐火可塑料線變化率試驗方法 | () |
| YB/T 5118-1993(2005) | 粘土質和高鋁質耐火可塑料強度試驗方法 | () |
| YB/T 5119-1993(2005) | 粘土質和高鋁質耐火可塑料可塑性指數試驗方法 | () |
| 編號 | 中文名稱 | 英文名稱 |