| 編號 | 中文名稱 | 英文名稱 |
|---|
| BS 3766-1978
| 機床用冷卻液泵規范
| Specification for coolant pumps for machine tools
|
| BS 4082-1-1969
| 立式管線離心泵外部尺寸規范.第1部分:"I"型
| Specification for external dimensions for vertical in-line centrifugal pumps - 'I' Type
|
| BS 4082-2-1969
| 立式管線離心泵外部尺寸規范.第2部分:"U"型
| Specification for external dimensions for vertical in-line centrifugal pumps - 'U' Type
|
| BS 4617-1983
| 液壓流體動力傳輸用動力泵和電動機性能的測定方法
| Methods for determining the performance of pumps and motors for hydraulic fluid power transmission
|
| BS 5173-102.3-1988
| 橡膠和塑料軟管及軟管組件試驗方法.第102部分:液壓試驗.第3節:燃料分配泵軟管體積膨脹測定
| Methods of test for rubber and plastics hoses and hose assemblies - Hydraulic pressure tests - Determination of volumetric expansion of fuel-dispensing pump hoses
|
| BS 5257-1975
| 臥式端吸離心泵(16bar)規范
| Specification for horizontal end-suction centrifugal pumps (16 bar)
|
| BS 5860-1980
| 水輪機、蓄水泵及渦輪泵的效率測定方法(熱力學法)
| Method for measuring the efficiency of hydraulic turbines, storage pumps and pump-turbines (thermodynamic method)
|
| BS 5944-1-1992
| 液壓動力系統和部件氣動噪聲測量.第1部分:液壓泵試驗方法
| Measurement of airborne noise from hydraulic fluid power systems and components - Method of test for pumps
|
| BS 5944-5-1985
| 液壓系統和部件氣動噪音測量.第5部分:使消聲室測定液壓泵聲功率等級的簡易方法
| Measurement of airborne noise from hydraulic fluid power systems and components - Simplified method of determining sound power levels from pumps using an anechoic chamber
|
| BS 5944-6-1992
| 液壓動力系統和部件氣動噪聲測量.第6部分:平行六面體傳聲器陣列測試液壓泵噪聲
| Measurement of airborne noise from hydraulic fluid power systems and components - Method of test for pumps using a parallelepiped microphone array
|
| BS 6169-1-1981
| 液態烴類體積測量方法.第1部分:置換流量計系統(不包括配劑泵)
| Methods for volumetric measurement of liquid hydrocarbons - Displacement meter systems (other than dispensing pumps)
|
| BS 6907-4-1988
| 露天礦和采石場的電氣裝置.第4部分:開采、層疊和處理機械設備、泵和低信號級及通信系統推薦標準
| Electrical installations for open-cast mines and quarries - Recommendations for winning, stacking and processing machinery, pumps and low signal level and communications systems
|
| BS 7117-2-1991
| 安裝在加油站并用以加液體燃料的計量泵和分配器.安裝指南
| Metering pumps and dispensers to be installed at filling stations and used to dispense liquid fuel - Guide to installation
|
| BS 7117-3-1991
| 安裝在加油站并用以加液體燃料的計量泵和分配器.安裝后維護指南
| Metering pumps and dispensers to be installed at filling stations and used to dispense liquid fuel - Guide to maintenance after installation
|
| BS 7250-1989
| 液壓傳動正排量泵和電動機導出量的測定方法
| Methods of determining the derived capacity of hydraulic fluid power positive displacement pumps and motors
|
| BS 7929-1999
| 泵鑄造設計程序鑒定指南
| Guide for the verification of a pump casing design procedure
|
| BS 799-7-1988
| 燃油設備.第7部分:有旋轉軸和外部傳動裝置的霧化燃油器泵的尺寸規范
| Oil burning equipment - Specification for dimensions of atomizing oil burner pumps with rotating shaft and external drive
|
| BS 8204-7-2003
| 找平層、底基和現場鋪筑地板材料.可泵送自找平找平層.實施規范
| Screeds, bases and in-situ floorings - Pumpable self-smoothing screeds - Code of practice
|
| BS DD CEN/TS 14825-2004
| 對流式供暖和制冷用帶有電動壓縮機的空氣調節器、液體制冷包和熱泵.部分負載條件下的檢驗和額定
| Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Testing and rating at part load conditions
|
| BS DD ENV 12102-1997
| 帶電驅動壓縮機的空調、加熱泵和除濕器.空氣噪聲的測量.聲功率水平的測定
| Air conditioners, heat pumps and dehumidifiers with electrically driven compressors - Measurement of airborne noise - Determination of the sound power level
|
| BS DD IEC TS 62091-2003
| 低壓開關設備和控制設備.固定式消防泵驅動器用控制器
| Low-voltage switchgear and controlgear - Controllers for drivers of stationary fire pumps
|
| BS EN 1012-1-1997
| 壓縮機和真空泵.安全性要求.壓縮機
| Compressors and vacuum pumps - Safety requirements - Compressors
|
| BS EN 1012-2-1997
| 壓縮機和真空泵.安全性要求.真空泵
| Compressors and vacuum pumps - Safety requirements - Vacuum pumps
|
| BS EN 1028-1-2002
| 消防泵.起動注油器的消防離心泵.分類.總則和安全性要求
| Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Classification - General and safety requirements
|
| BS EN 1028-2-2002
| 消防泵.帶起動油泵的消防離心泵.一般要求和安全性要求的驗證
| Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Verification of general and safety requirements
|
| BS EN 1076-1997
| 工作地點的環境.測定氣體和蒸氣用的泵吸附管.要求和試驗方法
| Workplace atmospheres - Pumped sorbent tubes for the determination of gases and vapours - Requirements and test methods
|
| BS EN 12157-1999
| 離心泵.機床用冷卻液泵裝置.公稱流動速率、尺寸
| Rotodynamic pumps - Coolant pump units for machine tools - Nominal flow rate, dimensions
|
| BS EN 12162-2001
| 液體泵.安全要求.液壓靜態試驗程序
| Liquid pumps - Safety requirements - Procedure for hydrostatic testing
|
| BS EN 12178-2003
| 制冷系統和熱泵.液位指示設備.要求、試驗和標記
| Refrigerating systems and heat pumps - Liquid level indicating devices - Requirements, testing and marking
|
| BS EN 12262-1999
| 旋轉動力泵.技術文獻.術語,交付范圍,布局
| Rotodynamic pumps - Technical documents - Terms, delivery range, layout
|
| BS EN 12263-1999
| 制冷系統和熱力泵.限壓安全開關裝置.要求和試驗
| Refrigerating systems and heat pumps - Safety switching devices for limiting the pressure - Requirements and tests
|
| BS EN 12284-2003
| 冷卻系統和加熱泵.閥.要求、試驗及標記
| Refrigerating systems and heat pumps - Valves - Requirements, testing and marking
|
| BS EN 12309-1-2000
| 凈熱輸入不超過70KW的燃氣吸收和吸收空氣調節式和/或熱力泵裝置
| Gas-fired absorption and adsorption air-conditioning and/or heat pump appliances with a net heat input not exceeding 70 kW - Safety
|
| BS EN 12309-2-2000
| 凈熱輸入不超過70KW的燃氣吸收和吸收空氣調節式和/或熱力泵裝置.能量的合理使用
| Gas-fired absorption and adsorption air-conditioning and/or heat pump appliances with a net heat input not exceeding 70 kW - Rational use of energy
|
| BS EN 1232-1997
| 工作場所環境.化學試劑的小型專用抽樣泵.要求和試驗方法
| Workplace atmospheres - Pumps for personal sampling of chemical agents - Requirements and test methods
|
| BS EN 12462-1998
| 生物技術.泵性能準則
| Biotechnology - Performance criteria for pumps
|
| BS EN 12483-1999
| 液泵.帶變頻機的泵裝置.擔保和兼容性試驗
| Liquid pumps - Pump units with frequency inverters - Guarantee and compatibility tests
|
| BS EN 12514-1-2000
| 油燃燒器供油系統的安裝.安全性要求和試驗.零部件、供油泵、控制和安全裝置、供油罐
| Installations for oil supply systems for oil burners - Safety requirements and tests - Parts, oil feed pumps, control and safety devices, supply tanks
|
| BS EN 12583-2000
| 供氣系統.壓縮機泵站.功能要求
| Gas supply systems - Compressor stations - Functional requirements
|
| BS EN 12639-2000
| 液壓泵和泵組.噪音測試規程.2級和3級精度
| Liquid pumps and pump units - Noise test code - Grade 2 and grade 3 of accuracy
|
| BS EN 12723-2000
| 液壓泵.泵和設備的通用術語.定義、數量、字母符號和單位
| Liquid pumps - General terms for pumps and installations - Definitions, quantities, letter symbols and units
|
| BS EN 12919-1999
| 工作場所空氣.體積流速大于51/min的化學試劑取樣用泵.要求和試驗方法
| Workplace atmospheres - Pumps for the sampling of chemical agents with a volume flow rate of over 51/min - Requirements and test methods
|
| BS EN 13136-2001
| 滅火系統和熱力泵.釋壓裝置和配套管道.計算方法
| Refrigerating systems and heat pumps - Pressure relief devices and their associated piping - Methods for calculation
|
| BS EN 13275-2000
| 低溫容器.低溫設備用泵
| Cryogenic vessels - Pumps for cryogenic service
|
| BS EN 13313-2002
| 制冷系統和加熱泵.人員的能力.
| Refrigerating systems and heat pumps - Competence of personnel
|
| BS EN 13617-1-2004
| 加油站.計量泵、分配器和遙控泵送裝置的性能和建造的安全要求
| Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units
|
| BS EN 13617-2-2004
| 加油站.計量泵和配油器上安全制動器的建造和性能的安全要求
| Petrol filling stations - Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers
|
| BS EN 13617-4-2004
| 加油站.計量泵和配油器用轉環的建造和性能的安全與環境要求
| Petrol filling stations - Safety and environmental requirements for construction and performance of swivels for use on metering pumps and dispensers
|
| BS EN 13951-2003
| 液泵.安全要求.農產食品設備.使用中衛生保證的設計原則
| Liquid pumps - Safety requirements - Agrifoodstuffs equipment - Design rules to ensure hygiene in use
|
| BS EN 14275-2003
| 車用燃料.汽油及柴油質量的評估.零售點油泵及商業點燃料自動售貨機的抽樣
| Automotive fuels - Assessment of petrol and diesel fuel quality - Sampling from retail site pumps and commercial site fuel dispensers
|
| BS EN 14343-2005
| 旋轉容積泵.驗收性能試驗
| Rotary positive displacement pumps — Performance tests for acceptance
|
| BS EN 14466-2005
| 消防泵.便攜式消防泵.安全和性能要求、試驗
| Fire fighting pumps - Portable pumps - Safety and performance requirements, tests
|
| BS EN 14511-1-2004
| 房間取暖和制冷用帶電動壓縮機的空氣調節裝置、液冷組件和熱泵.術語和定義
| Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling
|
| BS EN 14511-2-2004
| 房間取暖和制冷用帶電動壓縮機的空氣調節裝置、液冷組件和熱泵.試驗條件
| Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Test conditions
|
| BS EN 14511-3-2004
| 房間取暖和制冷用帶電動壓縮機的空氣調節裝置、液冷組件和熱泵.試驗方法
| Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Test methods
|
| BS EN 14511-4-2004
| 房間取暖和制冷用帶電動壓縮機的空氣調節裝置、液冷組件和熱泵.要求
| Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Requirements
|
| BS EN 14662-1-2005
| 環境空氣質量.測量苯濃度的標準方法.熱解吸和氣相色譜法后的泵取樣
| Ambient air quality - Standard method for measurement of benzene concentrations - Pumped sampling followed by thermal desorption and gas chromatography
|
| BS EN 14662-2-2005
| 環境空氣質量.苯濃度測量的標準方法.溶劑解吸和氣相色譜法后的泵送取樣
| Ambient air quality - Standard method for measurement of benzene concentrations - Pumped sampling followed by solvent desorption and gas chromatography
|
| BS EN 14662-3-2005
| 環境空氣質量.測量苯濃度的標準方法.自動泵取樣和現場氣相色譜法
| Ambient air quality - Standard method for measurement of benzene concentrations - Automated pumped sampling with in situ gas chromatography
|
| BS EN 14710-1-2005
| 消防泵.無起動注油器的消防離心泵.分類、一般要求和安全要求
| Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Classification, general and safety requirements
|
| BS EN 14710-2-2005
| 消防泵.無起動注油器的消防離心泵.一般要求和安全要求的驗證
| Fire-fighting pumps - Fire-fighting centrifugal pumps without primer - Verification of general and safety requirements
|
| BS EN 1736-2000
| 制冷系統和熱力泵.柔性管元件.振動隔絕器和膨脹節.要求,設計和安裝
| Refrigerating systems and heat pumps - Flexible pipe elements, vibration isolators and expansion joints - Requirements, design and installation
|
| BS EN 1861-1998
| 制冷系統和熱力泵.系統流量圖,管道和設備圖.布局和符號
| Refrigerating systems and heat pumps - System flow diagrams and piping and instrument diagrams - Layout and symbols
|
| BS EN 1947-2002
| 消防軟水管.消防泵和車用半剛性輸送軟水管和水管組件
| Fire-fighting hoses - Semi-rigid delivery hoses and hose assemblies for pumps and vehicles
|
| BS EN 22858-1993
| 端吸式離心泵(額定壓力16巴).命名、標稱效率點和尺寸
| End-suction centrifugal pumps (rating 16 bar) - Designation, nominal duty point and dimensions
|
| BS EN 23661-1993
| 端吸式離心泵的底板和安裝尺寸
| End-suction centrifugal pumps - Baseplate and installation dimensions
|
| BS EN 255-3-1997
| 帶電動壓縮機的空調器.液體制冷設備和熱力泵.加熱方式.衛生間熱水裝置的試驗和標記要求
| Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors - Heating mode - Testing and requirements for marking for sanitary hot water units
|
| BS EN 378-1-2000
| 制冷系統和加熱泵規范.安全性和環境要求.基本要求、定義、分類和選擇規范
| Specification for refrigerating systems and heat pumps - Safety and environmental requirements - Basic requirements, definitions, classification and selection criteria
|
| BS EN 378-2-2000
| 制冷系統和加熱泵規范.安全性和環境要求.設計、制造、試驗、標記和文獻
| Specification for refrigerating systems and heat pumps - Safety and environmental requirements - Design, construction, testing, marking and documentation
|
| BS EN 378-3-2000
| 制冷系統和加熱泵規范.安全性和環境要求.安裝現場和人員保護
| Specification for refrigerating systems and heat pumps - Safety and environmental requirements - Installation site and personal protection
|
| BS EN 378-4-2000
| 制冷系統和加熱泵規范.安全性和環境要求.操作、維修、檢修和回收
| Refrigerating systems and heat pumps - Safety and environmental requirements - Operation, maintenance, repair and recovery
|
| BS EN 45510-5-4-1998
| 發電站設備采購指南.水輪機、蓄水泵和水泵水輪機
| Guide for the procurement of power station equipment - Hydraulic turbines, storage pumps and pump-turbines
|
| BS EN 45510-6-4-2000
| 發電站設備采購指南.渦輪機輔助設備.泵
| Guide for the procurement of power station equipment - Turbine auxiliaries - Pumps - Pumps
|
| BS EN 50216-7-2002
| 電力變壓器和反應堆配件.運輸油用電泵
| Power transformers and reactor fittings - Electric pumps for transformer oil
|
| BS EN 60041-1995
| 水輪機,現場驗收試驗測定蓄水泵和渦輪泵液壓性能
| Field acceptance tests to determine the hydraulic performance of hydraulic turbines, storage pumps and pump-turbines
|
| BS EN 60193-1999
| 水輪機、蓄水泵和泵輪機.模型驗收試驗
| Hydraulic turbines, storage pumps and pump-turbines — Model acceptance tests |
| BS EN 60335-2-40-2003
| 家用和類似用途電器的安全規范.特殊要求.電熱泵、空氣調節器和去濕器
| Household and similar electrical appliances - Safety - Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
|
| BS EN 60335-2-41-2003
| 家用和類似用途電器.泵的特殊要求
| Household and similar electrical appliances - Particular requirements for pumps
|
| BS EN 60335-2-51-2003
| 家用和類似用途電器的安全.加熱和供水設施用固定式循環泵的特殊要求
| Specification for safety of household and similar electrical appliances - Particular requirements for stationary circulation pumps for heating and service water installations
|
| BS EN 60601-2-24-1998
| 醫療電氣設備.特殊安全要求.輸液泵和控制器的特殊安全要求.
| Medical electrical equipment - Particular requirements for safety - Particular requirements for the safety of infusion pumps and controllers
|
| BS EN 60609-1-2005
| 水輪機、蓄能泵和水泵水輪機.氣蝕損壞的評定.反擊式水輪機、蓄能泵和水泵水輪機的評定
| Hydraulic turbines, storage pumps and pump-turbines - Caviatation pitting evaltuation - Evalution in reaction turbines, storage pumps and pumps-turbines
|
| BS EN 60609-2-1998
| 水輪機、蓄能泵和水泵水輪機氣蝕損壞的評定.水斗式水輪機的評定
| Cavitation pitting evaluation in hydraulic turbines, storage pumps and pump turbines - Evaluation in Pelton turbines
|
| BS EN 60994-1993
| 水力機械(水輪機、蓄水泵和水輪泵)振動和脈動現場測量指南
| Guide for field measurement of vibrations and pulsations in hydraulic machines (turbines, storage pumps and pump-turbines)
|
| BS EN 61290-6-1-1998
| 光纖放大器.基本規范.泵漏參數測試方法.光信號分離器
| Optical fibre amplifiers - Basic specification - Test methods for pump leakage parameters - Optical demultiplexer
|
| BS EN 61702-2000
| 直接耦合光伏(PV)水泵系統的額定值
| Rating of direct coupled photovoltaic (PV) pumping systems
|
| BS EN 733-1995
| 帶支承架的額定值為10bar的端吸式離心泵.公稱負荷點、主要尺寸和命名系統
| End-suction centrifugal pumps, rating with 10 bar with bearing bracket - Nominal duty point, main dimensions, designation system
|
| BS EN 734-1995
| 側槽泵PN40.公稱負荷點、主要尺寸和命名系統
| Side channel pumps PN 40 - Nominal duty point, main dimensions, designation system
|
| BS EN 735-1995
| 旋轉動態泵的總體尺寸.公差
| Overall dimensions of rotodynamic pumps - Tolerances
|
| BS EN 752-6-1998
| 室外建筑物的排水和污水系統.泵抽排裝置
| Drain and sewer systems outside buildings - Pumping installations
|
| BS EN 809-1998
| 液體用泵和泵裝置.一般安全性要求
| Pumps and pump units for liquids - Common safety requirements
|
| BS EN ISO 13709-2003
| 石油、石化和天然氣工業用離心泵
| Centrifugal pumps for petroleum, petrochemical and natural gas industries
|
| BS EN ISO 13710-2004
| 石油、石化和天然氣工業.往復式變容真空泵
| Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps
|
| BS EN ISO 14847-1999
| 回轉容積泵.技術要求
| Rotary positive displacement pumps - Technical requirements
|
| BS EN ISO 15136-1-2001
| 石油和天然氣工業的鉆孔設備.人工提升用步進式空腔泵系統.泵
| Downhole equipment for petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Pumps
|
| BS EN ISO 15783-2003
| 無密封旋轉動力泵.II級.規范
| Seal-less rotodynamic pumps - Class II - Specification
|
| BS EN ISO 16330-2003
| 往復式正排量泵和泵裝置.技術要求
| Reciprocating positive displacement pumps and pump units - Technical requirements
|
| BS EN ISO 20763-2004
| 石油和相關產品.液壓液耐磨性的測定.葉輪泵法
| Petroleum and related products - Determination of anti-wear properties of hydraulic fluids - Vane pump method
|
| BS EN ISO 21049-2005
| 泵.離心泵和旋轉泵用軸封系統
| Pumps - Shaft sealing systems for centrifugal and rotary pumps
|
| BS EN ISO 2151-2004
| 聲學.壓縮機和真空泵的噪聲試驗規范.工程法(2級)
| Acoustics - Noise test code for compressors and vacuum pumps - Engineering method (Grade 2)
|
| BS EN ISO 5198-1999
| 離心式混流軸向泵.液壓性能試驗規程.精密級
| Centrifugal, mixed flow and axial pumps - Code for hydraulic performance tests - Precision class
|
| BS EN ISO 5199-2002
| 離心泵的技術規范.2級
| Technical specifications for centrifugal pumps - Class II
|
| BS EN ISO 7886-2-1996
| 一次性使用無菌皮下注射器.動力驅動注射器泵的注射器
| Sterile hypodermic syringes for single use - Syringes for use with power-driven syringe pumps
|
| BS EN ISO 8849-2003
| 小艇.電動直流艙底泵
| Small craft - Electrically operated direct-current bilge-pumps
|
| BS EN ISO 9905-1994
| 離心泵技術規范.I類
| Technical specifications for centrifugal pumps - Class I
|
| BS EN ISO 9906-2000
| 渦輪式泵.液壓性能驗收試驗.1和2級
| Rotodynamic pumps - Hydraulic performance acceptance tests - Grades 1 and 2
|
| BS EN ISO 9908-1994
| 離心泵技術規范.III類
| Technical specifications for centrifugal pumps - Class III
|
| BS IEC 60609-2-1998
| 水輪機、蓄能泵和水泵渦輪機空穴評估.水戽式水輪機的評估
| Cavitation pitting evaluation in hydraulic turbines, storage pumps and pump turbines - Evaluation in Pelton turbines
|
| BS IEC 61366-1-1998
| 水輪機、蓄能泵和水泵渦輪.投標文件.綜述及附錄
| Hydraulic turbines, storage pumps, and pump turbines - Tendering documents - General and annexes
|
| BS IEC 61366-2-1998
| 水輪機、蓄能泵和水泵渦輪.投標文件.弗蘭西斯渦輪機技術規范指南
| Hydraulic turbines, storage pumps, and pump turbines - Tendering documents - Guidelines for technical specifications for Francis turbines
|
| BS IEC 61366-3-1998
| 水輪機、蓄能泵和水泵渦輪.投標文件.水戽式水輪機的技術規范指南
| Hydraulic turbines, storage pumps, and pump turbines - Tendering documents - Guidelines for technical specifications for Pelton turbines
|
| BS IEC 61366-4-1998
| 水輪機、蓄能泵和水泵渦輪.投標文件.卡普蘭式水輪機和推進式水輪機的技術規范指南
| Hydraulic turbines, storage pumps, and pump turbines - Tendering documents - Guidelines for technical specifications for Kaplan and propeller turbines
|
| BS IEC 61366-5-1998
| 水輪機、蓄能泵和水泵渦輪.投標文件.管狀水輪機技術規范指南
| Hydraulic turbines, storage pumps, and pump turbines - Tendering documents - Guidelines for technical specifications for tubular turbines
|
| BS IEC 61366-6-1998
| 水輪機、蓄能泵和水泵渦輪.投標文件.水泵渦輪技術規范指南
| Hydraulic turbines, storage pumps, and pump turbines - Tendering documents - Guidelines for technical specifications for pump-turbines
|
| BS IEC 61366-7-1998
| 水輪機、蓄能泵和水泵渦輪.投標文件.蓄水泵技術規范指南
| Hydraulic turbines, storage pumps, and pump turbines - Tendering documents - Guidelines for technical specifications for storage pumps
|
| BS ISO 10767-1-1996
| 液壓流體動力.對系統和部件產生壓力波動級的測定.第1部分:泵精度法
| Hydraulic fluid power - Determination of pressure ripple levels generated in systems and components - Precision method for pumps
|
| BS ISO 10767-2-1999
| 液壓傳動.系統和元件中產生壓力波動值的測定.泵的簡化方法
| Hydraulic fluid power - Determination of pressure ripple levels generated in systems and components - Simplified method for pumps
|
| BS ISO 10816-5-2001
| 機械振動.在非旋轉部件上測量評價機械振動.水力發電廠和泵站機組
| Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Machine sets in hydraulic power and pumping plants
|
| BS ISO 12334-2000
| 航空航天.液壓的壓力補償?shù)淖兞枯斔捅?35000KPa系統的一般要求
| Aerospace - Hydraulic, pressure-compensated, variable delivery pumps - General requirements for 35000 kPa systems
|
| BS ISO 14617-9-2004
| 圖示的圖形符號.泵、壓縮機和風扇
| Graphical symbols for diagrams - Pumps, compressors and fans
|
| BS ISO 14681-1998
| 柴油發動機.燃料噴射泵試驗.燃料噴嘴的校準
| Diesel engines - Fuel injection pump testing - Calibrating fuel injectors
|
| BS ISO 14686-2003
| 液體比重的測定.水井的泵送試驗.設計、性能和使用的考慮和指南
| Hydrometric determinations - Pumping tests for water wells - Considerations and guidelines for design, performance and use
|
| BS ISO 16902-1-2003
| 液壓傳動.用聲強法測定聲功率級的試驗規程.工程法.泵
| Hydraulic fluid power - Test code for the determination of sound power levels using sound intensity techniques - Engineering method - Pumps
|
| BS ISO 17559-2004
| 液壓傳動.電控液壓泵.性能特征測定的試驗方法
| Hydraulic fluid power - Electrically controlled hydraulic pumps - Test methods to determine performance characteristics
|
| BS ISO 3019-1-2001
| 液力傳動.容積式泵和馬達的安裝法蘭盤和軸伸的尺寸及標識代碼.以米制單位表示的英制系列
| Hydraulic fluid power - Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors - Inch series shown in metric units
|
| BS ISO 3019-2-2001
| 液力傳動.容積式泵和馬達的安裝法蘭盤和軸伸的尺寸及標識代碼.米制系列
| Hydraulic fluid power - Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors - Metric series
|
| BS ISO 3069-2001
| 端吸離心泵.機械密封和軟密封件密封腔尺寸
| End-suction centrifugal pumps - Dimensions of cavities for mechanical seals and for soft packing
|
| BS ISO 4008-3-2003
| 道路車輛.噴油泵試驗.應用和試驗程序
| Road vehicles - Fuel injection pump testing - Application and test procedures
|
| BS ISO 4093-2000
| 柴油發動機.噴油泵.試驗用高壓管
| Diesel engines - Fuel injection pumps - High-pressure pipes for testing
|
| BS ISO 6145-2-2001
| 氣體分析.標定用混合氣體的制備.動態容量法.容積計量泵
| Gas analysis - Preparation of calibration gas mixtures using dynamic volumetric methods - Volumetric pumps
|
| BS ISO 6519-2004
| 柴油機.噴油泵.軸端和轂盤的錐度
| Diesel engines - Fuel injection pumps - Tapers for shaft ends and hubs
|
| BS ISO 7299-1997
| 柴油發動機.燃油注射泵端面安裝法蘭盤
| Diesel engines - End-mounting flanges for fuel injection pumps
|
| BS ISO 7612-2006
| 柴油機.共軌燃料噴射系統用基座安裝直列式噴油泵和高壓供油泵.安裝尺寸
| Diesel engines - Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems - Mounting dimensions
|
| BS ISO 7879-1998
| 柴油發動機.托架安裝直列式燃料噴射泵.安裝尺寸
| Diesel engines - Cradle mounted in-line fuel injection pumps - Mounting dimensions
|
| BS ISO 7919-5-2005
| 機械振動.通過對旋轉軸的測量評價機械振動.水力發電廠和泵站機組
| Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Machine sets in hydraulic power generating and pumping plants
|
| BS ISO 8976-2004
| 夾扭鉗和剪切鉗.水泵鉗.尺寸和試驗值
| Pliers and nippers - Multiple slip joint pliers - Dimensions and test values
|
| BS M 65-1987
| 壓力補償變量液壓泵規范
| Specification for pressure compensated variable delivery hydraulic pumps
|
| DD ENV 12102-1997
| 帶電動壓縮機的空調器、熱力泵和除濕器.機載噪音的測量.噪音等級的測定.
| Air conditioners, heat pumps and dehumidifiers with electrically driven compressors. Measurement of airborne noise. Determination of the sound power level
|
| KIT 76-2001
| 制冷系統和熱泵.安全和環境規定(BS EN 378)
| Refrigeration and heat pumps - Safety and environment set (BS EN 378)
|
| 編號 | 中文名稱 | 英文名稱 |
|---|