| 編號 | 中文名稱 | 英文名稱 |
|---|
| ANSI B93.62M-1982
| 液壓傳動.線性執行器中往復式動力密封設備.泄漏的試驗、測量和報告方法
| Hydraulic fluid power - Reciprocating dynamic sealing devices in linear actuators - Method of testing, measuring and reporting leakage
|
| ANSI B93.76-1988
| 液壓氣動缸.往復運動用活塞和活塞桿密封腔的尺寸和公差
| Hydraulic Fluid Power - Cylinders - Housings for Piston and Rod Seals in Reciprocating Applications - Dimensions and Tolerances
|
| ANSI B93.98M-1987
| 液壓用旋轉軸凸緣密封圈的公稱尺寸和公差
| Fluid Power - Rotary Shaft Lip Type Seals - Nominal Dimensions and Tolerances
|
| ANSI C119.6-2006
| 鋁和銅導線用額定電壓小于等于600V的非密封多端連接裝置
| Standard for Non-Sealed, Multiport Connector Systems Rated 600 Volts or Less for Aluminum and Copper Conductors
|
| ANSI C18.2M-1997
| 電池組.密封可再充電的鎳鎘圓柱形裸露的和有外殼的蓄電池
| Batteries - Sealed Rechargeable (Secondary) Nickel-Cadmium Cylindrical Bare Cells and Jacketed Batteries
|
| ANSI C57.12.52-1981
| 三相，高壓:601至34500伏，低壓:208Y/120至4160伏,容量不小于501千伏安,密封干式電力變壓器的要求
| Requirements for Sealed Dry-Type Power Transformers, 501 kVA and Larger, Three-Phase, with High-Voltage 601 to 34 500 Volts, Low-Voltage 208Y/120 to 4160 Volts
|
| ANSI/(NFPA) T3.19.25 R1-2004
| 信息報告.液壓系統.密封裝置.彈性密封件和隔離裝置的存儲、搬運和安裝
| Information Report - Fluid Power Systems - Sealing Devices - Storage, Handling, and Installation of Elastomeric Seals and Exclusion Devices
|
| ANSI/AAMI ST77-2006
| 可再利用的醫療設備殺菌用密封裝置
| Containment devices for reusable medical device sterilization
|
| ANSI/AAMI/ISO 11607-2-2006
| 最后滅菌的醫療器械的包裝.第2部分:組成、密封和裝配過程的確認和要求
| Packaging for terminally sterilized medical devices - Part 2: Validation and requirements for forming, sealing and assembly processes
|
| ANSI/ABMA/ISO 13412-1997
| 航空航天.飛機結構用軛型單列密封的滾針滾道式滾子.英制系列
| Aerospace - Airframe Needle Track Roller, Yoke Type, Single-Row, Sealed - Inch Series
|
| ANSI/ABMA/ISO 13413-1997
| 航空航天.飛機結構用軛型、雙列密封的滾針滾道式滾子.英制系列
| Aerospace - Airframe Needle Track Roller, Yoke Type, Double-Row, Sealed - Inch Series
|
| ANSI/ABMA/ISO 13415-1997
| 航空航天.飛機結構用柱型單列密封的滾針滾道式滾子.英制系列
| Aerospace - Airframe Needle Roller Bearings, Stud Type, Single-Row, Sealed - Inch Series
|
| ANSI/ABMA/ISO 13416-1997
| 航空航天.飛機結構用軛型單列密封的滾針滾道式滾子.米制系列
| Aerospace - Airframe Needle Track Roller, Yoke Type, Single-Row, Sealed - Metric Series
|
| ANSI/ABMA/ISO 13417-1997
| 航空航天.飛機結構用柱型單列密封的滾針滾道式滾子.米制系列
| Aerospace - Airframe Needle Track Roller, Stud Type, Single-Row, Sealed - Metric Series
|
| ANSI/ABMA/ISO 14193-1998
| 航空航天.飛機結構用中等負荷擴展內圈單列自位密封球面滾子軸承.英制系列
| Aerospace - Airframe Spherical Roller Bearings, Single-Row, Self-Aligning, Sealed, Extended Inner Ring, Intermediate Duty - Inch Series
|
| ANSI/ABMA/ISO 14194-1998
| 航空航天.飛機結構用重負荷擴展內圈自位雙列密封球面滾子軸承.英制系列
| Aerospace - Airframe Spherical Roller Bearings, Double-Row, Self-Aligning, Sealed, Extended Inner Ring, Heavy Duty - Inch Series
|
| ANSI/ABMA/ISO 14195-1998
| 航空航天.飛機結構用輕負荷扭力管設計的自位雙列密封球面滾子軸承.英制系列
| Aerospace - Airframe Spherical Roller Bearings, Double-Row, Self-Aligning, Sealed, Torque Inner Tube Design, Light Duty - Inch Series
|
| ANSI/ABMA/ISO 14196-1998
| 航空航天.飛機結構用重負荷普通內圈自位雙列密封球面滾子軸承.英制系列
| Aerospace - Airframe Spherical Roller Bearings, Double-Row, Self-Aligning, Sealed, Plain Inner Ring, Heavy Duty - Inch Series
|
| ANSI/ABMA/ISO 14197-1998
| 航空航天.飛機結構用中等負荷自位單列密封球面滾子軸承.英制系列
| Aerospace - Airframe Spherical Roller Bearings, Single-Row, Self-Aligning, Sealed, Intermediate Duty - Inch Series
|
| ANSI/ABMA/ISO 14206-1998
| 航空航天.飛機結構用輕負荷單列剛性密封球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Rigid, Sealed, Light Duty - Inch Series
|
| ANSI/ABMA/ISO 14207-1998
| 航空航天.飛機結構用輕負荷密封精密單列剛性球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Rigid, Precision, Sealed, Light Duty - Inch Design
|
| ANSI/ABMA/ISO 14208-1998
| 航空航天.飛機結構用中等負荷密封單列剛性球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Rigid, Sealed, Intermediate Duty - Inch Design
|
| ANSI/ABMA/ISO 14209-1998
| 航空航天.飛機結構用中等負荷密封精密單列剛性球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Rigid, Precision, Intermediate Duty - Inch Design
|
| ANSI/ABMA/ISO 14210-1998
| 航空航天.飛機結構用扭力管設計的輕負荷密封單列剛性球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Rigid, Torque Tube Design, Light Duty - Inch Design
|
| ANSI/ABMA/ISO 14211-1998
| 航空航天.飛機結構用輕負荷扭力管設計的單列剛性密封精密球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Rigid, Precision, Sealed, Torque Tube Design, Light Duty - Inch Series
|
| ANSI/ABMA/ISO 14212-1998
| 航空航天.飛機結構用扭力管設計的超輕負荷密封單列剛性球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Rigid, Torque Tube Design, Extra-Light Duty - Inch Design
|
| ANSI/ABMA/ISO 14213-1998
| 航空航天.飛機結構用扭力管設計的超輕負荷密封精密單列剛性球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Rigid, Precision, Sealed, Torque Tube Designa, Extra-Light Duty - Inch Series
|
| ANSI/ABMA/ISO 14214-1998
| 航空航天.飛機結構用重負荷密封雙列剛性球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Double-Row, Rigid, Sealed, Heavy Duty - Inch Series
|
| ANSI/ABMA/ISO 14215-1998
| 航空航天.飛機結構用重負荷密封精密雙列剛性球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Double-Row, Rigid, Precision, Sealed, Heavy Duty - Inch Series
|
| ANSI/ABMA/ISO 14216-1998
| 航空航天.飛機結構用重負荷密封雙列自調心球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Double-Row, Self-Aligning, Sealed, Heavy Duty - Inch Series
|
| ANSI/ABMA/ISO 14217-1998
| 航空航天.飛機結構用重負荷密封精密雙列自調心球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Double-Row, Self-Aligning, Precision, Sealed, Heavy Duty - Inch Series
|
| ANSI/ABMA/ISO 14218-1998
| 航空航天.飛機結構用重負荷密封單列自調心球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Self-Aligning, Sealed, Heavy Duty - Inch Series
|
| ANSI/ABMA/ISO 14219-1998
| 航空航天.飛機結構用重負荷密封精密單列自調心球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Self-Aligning, Precision, Sealed, Heavy Duty - Inch Series
|
| ANSI/ABMA/ISO 14220-1998
| 航空航天.飛機結構用輕負荷密封單列自調心球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Self-Aligning, Sealed, Light Duty - Inch Series
|
| ANSI/ABMA/ISO 14221-1998
| 航空航天.飛機結構用輕負荷密封精密單列自調心球軸承.英制系列
| Aerospace - Airframe Ball Bearings, Single-Row, Self-Aligning, Precision, Sealed, Light Duty - Inch Series
|
| ANSI/API 682-2004
| 泵.離心泵和回轉泵的軸密封裝置
| Pumps - Shaft Sealing Systems for Centrifugal and Rotary Pumps
|
| ANSI/API 685-1999
| 用于石油、重型化工和燃氣行業的非密封離心泵
| Sealless Centrifugal Pumps for Petroleum, Heavy Duty Chemical and Gas Industry Services
|
| ANSI/ASHRAE 97-2007
| 試驗制冷系統內用材料化學穩定性的密封玻璃管法
| Sealed Glass Tube Method to Test the Chemical Stability of Materials for Use Within Refrigerant Systems
|
| ANSI/ASME A112.19.15-2005
| 帶壓力密封門的浴池/旋渦浴池
| Bathtub/Whirlpool Bathtubs with Pressure Sealed Doors
|
| ANSI/ASME B1.20.5-1991
| 干密封管螺紋的測量(英制)
| Gaging for Dryseal Pipe Threads (Inch)
|
| ANSI/ASME B40.2-2000
| 隔膜密封
| Diaphragm Seals
|
| ANSI/ASME B73.3M-2003
| 非密封臥式端部吸水管規范
| Specification for Sealless Horizontal End Suction
|
| ANSI/ASME MFC-2M-1983
| 密封管道中液體流量測量的不確定度
| Measurement Uncertainty for Fluid Flow in Closed Conduits
|
| ANSI/ASME MFC-5M-1985
| 用時差法超聲波流量計測量密封管道中液體流量
| Measurement of Liquid Flow in Closed Conduits using Transit-Time Ultrasonic Flowmeters
|
| ANSI/ASME MFC-8M-2001
| 密封管中流體流量.主要設備和次要設備間壓力信號傳輸用連接件
| Fluid Flow in Closed Conduits - Connections for Pressure Signal Transmission Between Primary and Secondary Devices
|
| ANSI/ASME PTC12.1-2000
| 性能測試規范.密封式熱水器
| Performance Test Code - Closed Feedwater Heaters
|
| ANSI/ASSE 1018-2002
| 分離器密封起動閥.輕便供水裝置
| Trap Seal Primer Valves - Potable Water Supplied
|
| ANSI/ASSE 1044-2002
| 分離器密封起動閥.排水裝置類型和電子設計類型
| Trap Seal Primer Devices - Drainage Types and Electronic Design Types
|
| ANSI/ASTM C808-2000
| 人造碳和石墨軸承與密封材料的摩擦力和磨損結果報告指南
| Guideline for Reporting Friction and Wear Test Results of Manufactured Carbon and Graphite Bearing and Seal Materials
|
| ANSI/ASTM D3139a-1996
| 使用柔韌彈性體密封的塑料壓力管接頭規范
| Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals
|
| ANSI/ASTM D3212-1996
| 軟性人造橡膠密封的排污水塑料管連接件規范
| Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
|
| ANSI/ASTM D5642-1999
| 密封管化學兼容性試驗的試驗方法
| Test Method for Sealed Tube Chemcal Compatability Test
|
| ANSI/ASTM D6546-2000
| 工業用液壓油密封圈兼容性的測定試驗方法和提議限制
| Test Methods and Suggested Limits for Determining the Compatibility of Elastomer Seals for Industrial Hydraulic Fluid Applications
|
| ANSI/ASTM D7216-2005
| 汽車機油與傳統密封彈性體兼容性測定的試驗方法
| Test Method for Determining Automotive Engine Oil Compatibility With Typical Seal Elastomers
|
| ANSI/ASTM E1494a-1992
| 含石棉易碎建筑材料密封劑噴涂或鏝刀涂抹規程
| Practice for Encapsulants for Spray-or-Trowel-Applied Friable Asbestos-Containing Building Materials (04.11)
|
| ANSI/ASTM F1073-1987
| 船用防水、防氣體/防空氣和防風雨門配件和非密封門規范
| Specification for Door Fittings, for Watertight/Gastight/Airtight, Weathertight, and Non-Tight Doors, for Marine Use
|
| ANSI/ASTM F1365-1991
| 采用柔性合成橡膠密封件的塑料地下管道接頭耐水滲透性試驗方法
| Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints which Use Flexible Elastomeric Seals
|
| ANSI/ASTM F1429-1999
| 用柔性合成橡膠密封件固定在套桶中的塑料地下管道接頭組合力試驗方法
| Test Method for Assembly Force of Plastic Underground Conduit Joints that Use Flexible Elastomeric Seals Located in the Bell
|
| ANSI/ASTM F1431-1992
| 內燃機排氣用水密封器規范
| Specification for Water Trap for Diesel Exhaust
|
| ANSI/ASTM F1511-2007
| 船泵設施用機械密封件規范
| Specification for Mechanical Seals for Shipboard Pump Applications
|
| ANSI/ASTM F1837M-1997
| 熱縮電纜端口密封規范(米制)
| Specification for Heat-Shrink Cable Entry Seals (Metric)
|
| ANSI/ASTM F2131-2003
| 密封管用聚氯乙烯薄試樣擺錘沖擊試驗
| Charpy Impact Test on Thin Specimens of Polyethylene Used in Pressurized Pipes
|
| ANSI/ASTM F2331-2004
| 測定熱塑性螺紋管和配件材料的螺紋密封件的化學兼容性的試驗方法
| Test Method for Determining Chemical Compatibility of Thread Sealants with Thermoplastic Threaded Pipe and Fittings Materials
|
| ANSI/ASTM F477-2007
| 連接塑料管的彈性體密封件(墊圈)用規范
| Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
| ANSI/ASTM F542-2007
| 電子元件及微電子元件封裝用密封化合物發熱溫度的試驗方法
| Test Method for Exothermic Temperature of Encapsulating Compounds for Electronic and Microelectronic Encapsulation
|
| ANSI/ASTM F913-2002
| 連接塑料管用熱塑彈性密封件(墊圈)規范
| Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
| ANSI/AWWA C504-2006
| 橡膠墊密封蝶閥
| Rubber-Seated Butterfly Valves
|
| ANSI/EIA 186-14E-1985
| 無源電子元器件.測試方法14:板的密封試驗
| Passive Electronic Component Parts - Test Method 14, Panel Seal Test
|
| ANSI/HI 4.1-4.6-2000
| 無密封旋轉式泵.術語、定義、應用、操作和測試
| Sealless Rotary Pumps - Nomenclature, Definitions, Applications, Operation and Test
|
| ANSI/HI 5.1-5.6-2000
| 無密封離心泵.術語、定義、應用、操作和測試
| Sealless Centrifugal Pumps for Nomenclature, Definitions, Application, Operation and Test
|
| ANSI/IEEE C37.20.1a-2005
| 金屬殼密封的低壓電力線路斷路器開關設備標準.修改1:短時間和短路可耐電流測試;多電纜連接的最小區域
| Standard for Metal-Enclosed Low-Voltage Power Circuit Breaker Switchgear - Amendment 1: Short-Time and Short-Circuit Withstand Current Tests; Minimum Areas for Multiple Cable Connections
|
| ANSI/IEEE C37.20.1b-2006
| 金屬密封的低壓電力斷路器開關設備標準.修改件2:直流電(DC)牽引電力開關控制和輔助電力布線的附加要求
| Standard for Metal-Enclosed Low-Voltage Power Circuit Breaker Switchgear - Amendment 2: Additional Requirements for Control and Auxiliary Power Wiring in DC Traction Power Switchgear
|
| ANSI/IEEE C57.12.01-2005
| 包括固體澆鑄和/或樹脂密封繞組的干式配電和電力變壓器的標準.一般要求
| Standard General Requirements for Dry-Type Distribution and Power Transformers Including Those with Solid-Cast and/or Resin Encapsulated Windings
|
| ANSI/IEEE C57.12.60-1998
| 固體澆鑄和樹脂密封的電力和配電變壓器絕緣系統熱評定試驗程序指南
| Guide for Test Procedures for Thermal Evaluation of Insulation Systems for Solid Cast and Resin-Encapsulated Power and Distribution Transformers
|
| ANSI/ISA 12.27.01-2002
| 電氣系統和可燃或易燃加工液體間工藝密封的要求
| Requirements for Process Sealing Between Electrical Systems and Flammable or Combustible Process Fluids
|
| ANSI/ISA 60079-18(12.23.01)-2005
| 等級I、危險區域1(已分級)場所用電氣器具:保護類型.密封'm'型
| Electrical Apparatus for Use in Class I, Zone 1 Hazardous (Classified) Locations: Type of Protection - Encapsulation 'm'
|
| ANSI/ISA 76.00.02-2002
| 表面安裝流體分配元器件的模塊化元器件接口.第1部分:合成橡膠密封件
| Modular Component Interfaces for Surface-Mount Fluid Distribution Components - Part 1: Elastomeric Seals
|
| ANSI/NEMA C119.1-2006
| 額定功率600V 的密封絕緣地下連接器系統
| Sealed Insulated Underground Connector System Rated 600 Volts
|
| ANSI/SAE J110-1997
| 密封件.徑向唇邊的試驗
| Seals - Testing of Radial Lip
|
| ANSI/SAE J1172-1993
| 密封法蘭發動機飛輪殼
| Engine Flywheel Housings with Sealed Flanges
|
| ANSI/SAE J1453-1998
| O型圈表面密封配件
| Fitting - O-Ring Face Seal
|
| ANSI/SAE J2244/3-1998
| 液壓傳動和通用連接.帶ISO 261螺紋和O形密封圈的孔及螺柱端.第3部分:輕型(L系列)螺柱端.尺寸、設計、試驗方
| Connections for Fluid Power and General Use-Ports and Stud Ends with ISO 261 Threads and O-Rings Sealing - Part 3: Light-Duty (L Series) Stud Ends - Dimensions, Design, Test Methods, and Requirements
|
| ANSI/SAE J572-1993
| 建筑和工業機器用密封照明裝置的要求
| Requirements for Sealed Lighting Unit for Construction and Industrial Machines
|
| ANSI/SAE J598-1994
| 用于建筑、工業和林業機械的密封照明裝置
| Sealed Lighting Units for Construction, Industrial, and Forest Machinery
|
| ANSI/SAE J654-1993
| 固定和往復式彈性材料傳動裝置密封件
| Static and Reciprocating Elastomeric Transmission Seals
|
| ANSI/TIA/EIA 455-23A-1985
| 光纖元件密封的漏氣試驗
| Air Leakage Testing of Fiber Optic Component Seals
|
| ANSI/UL 2390-2004
| 帶密封板的防風瀝青墻面板試驗方法的安全標準
| Standard for Safety for Test Method for Wind Resistant Asphalt Shingles with SealedTabs
|
| ANSI/UL 486D-2005
| 密封導線連接器的安全標準
| Standard for Safety for Sealed Wire Connectors
|
| ASME B16.21-1992
| 管法蘭用非金屬平密封墊
| (Nonmetallic flat gaskets for pipe flanges)
|
| ASME B40.2-1991
| 隔膜式密封件
| (Diaphragm seals)
|
| ASME MFC-16M-1995
| 用電磁流量計在密封管中對液體流量的測量
| (Measurement of fluid flow in closed conduits by means of electromagnetic flowmeters)
|
| ASME MFC-1M-1991
| 密封管道中液體流量測量用術語匯編
| (Glossary of terms used in measurement of fluid flow in pipes)
|
| ASME MFC-2M-1983
| 密封管道中液體流量測量的不確定度
| (Measurement uncertainty for fluid flow in closed conduits)
|
| ASME PTC 12.1-2000
| 密封供水加熱器
| (Closed feedwater heaters)
|
| ASTM C 1016-2002
| 密封劑背襯(填縫)料吸水率測定的標準試驗方法
| Standard Test Method for Determination of Water Absorption of Sealant Backing (Joint Filler) Material
|
| ASTM C 1021-2001
| 建筑密封料試驗用實驗室的標準實施規程
| Standard Practice for Laboratories Engaged in the Testing of Building Sealants
|
| ASTM C 1083-2006
| 彈性泡沫墊圈和密封材料吸水性的標準試驗方法
| Standard Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials
|
| ASTM C 1087-2000
| 測定門窗玻璃結構裝置中與附件一同使用的液態密封料相容性的標準試驗方法
| Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
|
| ASTM C 1135-2000
| 測定結構密封件的粘著抗拉強度特性的標準試驗方法
| Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
|
| ASTM C 1183-2004
| 彈性密封件擠壓比的標準試驗方法
| Standard Test Method for Extrusion Rate of Elastomeric Sealants
|
| ASTM C 1184-2005
| 結構硅密封件的標準規范
| Standard Specification for Structural Silicone Sealants
|
| ASTM C 1193a-2005
| 接縫密封劑使用的標準指南
| Standard Guide for Use of Joint Sealants
|
| ASTM C 1241-2000
| 凝固過程中膠乳密封劑體積收縮的標準試驗方法
| Standard Test Method for Volume Shrinkage of Latex Sealants During Cure
|
| ASTM C 1246-2000
| 彈性體密封劑凝固后熱老化對重量損失、裂開和粉化影響的標準試驗方法
| Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure
|
| ASTM C 1247-1998
| 連續浸液的密封劑壽命標準試驗方法
| Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids
|
| ASTM C 1248-2006
| 用接縫密封膠著色多孔襯底的標準試驗方法
| Standard Test Method for Staining of Porous Substrate by Joint Sealants
|
| ASTM C 1249a-2006
| 建筑密封玻璃用密封絕緣玻璃組件的二次密封標準規范
| Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
|
| ASTM C 1253-1993
| 測定密封層背襯除氣能力的標準試驗方法
| Standard Test Method for Determining the Outgassing Potential of Sealant Backing
|
| ASTM C 1257a-2006
| 溶劑釋放型密封劑加速老化的標準試驗方法
| Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants
|
| ASTM C 1265-1994
| 鑲嵌玻璃時對隔熱玻璃邊緣密封劑的抗拉性能的標準試驗方法
| Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
|
| ASTM C 1266-2002
| 預制膠帶密封劑流動特性的標準試驗方法
| Standard Test Method for Flow Characteristics of Preformed Tape Sealants
|
| ASTM C 1299-2003
| 液體密封劑選用的標準指南
| Standard Guide for Use in Selection of Liquid-Applied Sealants
|
| ASTM C 1311-2002
| 溶劑釋放器密封劑的標準規范
| Standard Specification for Solvent Release Sealants
|
| ASTM C 1315-2007
| 固化和密封混凝土用有特殊性能的液態薄膜成形混合物用標準規范
| Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete
|
| ASTM C 1330-1996
| 與冷卻液密封膠一起使用的圓柱形密封膠襯標準規范
| Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants
|
| ASTM C 1367-2006
| 密封件升溫狀態下靜載阻力的標準試驗方法
| Standard Test Method for Dead Load Resistance of a Sealant in Elevated Temperatures
|
| ASTM C 1375-1997
| 用于測試建筑物密封和膠粘劑的基質的標準指南
| Standard Guide for Substrates Used in Testing Building Seals and Sealants
|
| ASTM C 1382-2005
| 測定用于外部絕緣和精整系統連接件的密封劑抗拉黏著性能的試驗方法
| Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints
|
| ASTM C 1392-1998
| 評價構造密封門窗玻璃破壞的標準指南
| Standard Guide for Evaluating Failure of Structural Sealant Glazing
|
| ASTM C 1442-2006
| 用人工老化儀對密封件進行試驗的標準實施規范
| Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
|
| ASTM C 1472-2006
| 確定密封層接縫面寬度時位移和其他效應計算的標準指南
| Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
|
| ASTM C 1501-2004
| 用實驗室加速風化程序測定建筑物密封材料顏色穩定性的標準試驗方法
| Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures
|
| ASTM C 1518-2004
| 預硫化的彈性硅密封劑標準規范
| Standard Specification for Precured Elastomeric Silicone Joint Sealants
|
| ASTM C 1519-2004
| 用實驗室加速老化程序評價建筑物結構密封劑耐用性的標準規程
| Standard Practice for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
|
| ASTM C 1520-2002
| 乳膠密封劑可涂性標準指南
| Standard Guide for Paintability of Latex Sealants
|
| ASTM C 1521a-2002
| 評價已安裝上的防風雨的密封接頭粘結性的標準實施規程
| Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
|
| ASTM C 1523-2004
| 預硫化彈性連接密封劑的模量、抗撕裂性和粘結性能測定的標準試驗方法
| Standard Test Method for Determining Modulus, Tear and Adhesion Properties of Precured Elastomeric Joint Sealants
|
| ASTM C 1536-2003
| 氣溶膠泡沫密封劑流動性測量的標準試驗方法
| Standard Test Method for Measuring the Yield for Aerosol Foam Sealants
|
| ASTM C 1564-2004
| 安全玻璃系統用硅酮密封膠使用的標準指南
| Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
|
| ASTM C 1589-2005
| 建筑密封件和密封劑的室外老化的標準規程
| Standard Practice for Outdoor Weathering of Construction Seals and Sealants
|
| ASTM C 1619-2005
| 混凝土結構連接用彈性密封件的標準規范
| Standard Specification for Elastomeric Seals for Joining Concrete Structures
|
| ASTM C 1620-2005
| 氣溶膠聚氨酯和氣溶膠膠乳泡沫密封劑的標準規范
| Standard Specification for Aerosol Polyurethane and Aerosol Latex Foam Sealants
|
| ASTM C 1635-2006
| 在固定范圍內密封劑粘結特性評價的標準試驗方法
| Standard Test Method to Evaluate Adhesion/Cohesion Properties of a Sealant at Fixed Extension
|
| ASTM C 509-2006
| 多孔彈性預成型墊片和密封材料標準規范
| Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material
|
| ASTM C 510a-2005
| 單一或多組分接縫密封劑的著色和顏色變化的標準試驗方法
| Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants
|
| ASTM C 603-2004
| 彈性密封料的擠壓率和使用壽命的標準試驗方法
| Standard Test Method for Extrusion Rate and Application Life of Elastomeric Sealants
|
| ASTM C 639-2001
| 彈性密封料流變(流動)特性的標準試驗方法
| Standard Test Method for Rheological (Flow) Properties of Elastomeric Sealants
|
| ASTM C 661-2006
| 用硬度計測量彈性密封件的壓痕硬度的標準試驗方法
| Standard Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer
|
| ASTM C 717a-2007
| 建筑物密封件和密封劑的標準術語
| Standard Terminology of Building Seals and Sealants
|
| ASTM C 719-1993
| 在循環運動條件下彈性接合密封料的粘著性和粘結力的標準試驗方法(Hockman循環)
| Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
|
| ASTM C 731-2000
| 包裝老化后膠乳密封料可擠壓性的標準試驗方法
| Standard Test Method for Extrudability, After Package Aging, of Latex Sealants
|
| ASTM C 732-2006
| 人工風蝕對膠乳密封料老化效果的標準試驗方法
| Standard Test Method for Aging Effects of Artificial Weathering on Latex Sealants
|
| ASTM C 734-2006
| 膠乳密封料受人工氣候影響后的低溫柔韌性的標準試驗方法
| Standard Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering
|
| ASTM C 736-2000
| 膠乳密封化合物的伸縮性及粘著力的試驗方法
| Standard Test Method for Extension-Recovery and Adhesion of Latex Sealants
|
| ASTM C 793-2005
| 加速風化對彈性接縫密封膠影響的標準試驗方法
| Standard Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants
|
| ASTM C 808-1975
| 炭加工的及石墨制承重材料和密封材料的磨擦及磨蝕結果的報告標準指南
| Standard Guideline for Reporting Friction and Wear Test Results of Manufactured Carbon and Graphite Bearing and Seal Materials
|
| ASTM C 834-2005
| 膠乳密封料標準規范
| Standard Specification for Latex Sealants
|
| ASTM C 864-2005
| 致密彈性壓縮密封墊片、定位塊和隔板的標準規范
| Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers
|
| ASTM C 877-2001
| 混凝土管、人孔和預制箱形截面用外部密封帶的標準規范
| Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections
|
| ASTM C 877M-2001
| 混凝土管、人孔和預制箱形截面用外部密封帶的標準規范(米制)
| Standard Specification for External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections [Metric]
|
| ASTM C 908-2000
| 預制密封帶的屈服強度的標準試驗方法
| Standard Test Method for Yield Strength of Preformed Tape Sealants
|
| ASTM C 910-2006
| 單一成份彈性溶劑釋放型密封膠的粘結力及粘聚力的標準試驗方法
| Standard Test Method for Bond and Cohesion of One-Part Elastomeric Solvent Release-Type Sealants
|
| ASTM C 919-2002
| 聲學設備中密封料使用的標準實施規范
| Standard Practice for Use of Sealants in Acoustical Applications
|
| ASTM C 961-2006
| 密封材料的搭接剪切強度的標準試驗方法
| Standard Test Method for Lap Shear Strength of Sealants
|
| ASTM C 964-2007
| 鎖條式密封墊玻璃窗的標準指南
| Standard Guide for Lock-Strip Gasket Glazing
|
| ASTM C 972-2000
| 密封帶的壓縮恢復的標準試驗方法
| Standard Test Method for Compression-Recovery of Tape Sealant
|
| ASTM C 990-2006
| 使用預制撓性接縫密封膠的混凝土管道、人孔和預制箱形件的接縫的標準規范
| Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
|
| ASTM C 990M-2006
| 使用預制柔性接頭縫密封件的混凝土管道、人孔和預制箱型部件用接頭的標準規范(米制)
| Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants [Metric]
|
| ASTM D 1546-1996
| 透明地板密封劑的性能試驗的標準操作規程
| Standard Practice for Testing the Performance of Clear Floor Sealers
|
| ASTM D 1874-1962
| 纖維板船運箱頂蓋自動機密封用水可溶或溶劑可溶的液體膠粘劑
| Water- or Solvent-Soluble Liquid Adhesives for Automatic Machine Sealing of Top Flaps of Fiberboard Shipping Cases
|
| ASTM D 1974-1998
| 纖維板箱封口、密封及加固方法的標準實施規范
| Standard Practice for Methods of Closing, Sealing, and Reinforcing Fiberboard Boxes
|
| ASTM D 1985-2003
| 接縫和裂紋粘合用密封膠測試用混凝土塊制備的標準實施規范
| Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks
|
| ASTM D 2202-2000
| 密封料塌落的標準試驗方法
| Standard Test Method for Slump of Sealants
|
| ASTM D 2203-2001
| 密封劑著色的標準試驗方法
| Standard Test Method for Staining from Sealants
|
| ASTM D 2377-2000
| 填縫混合料及密封料消粘時間的標準試驗方法
| Standard Test Method for Tack-Free Time of Caulking Compounds and Sealants
|
| ASTM D 2527-1983
| 橡膠密封件的接合強度
| Standard Specification for Rubber Seals - Splice Strength
|
| ASTM D 2628-1991
| 混凝土路面用預制聚氯丁彈性接縫密封膠的標準規范
| Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements
|
| ASTM D 2835-1989
| 混凝土鋪面用預制壓縮密封物安裝用潤滑劑的標準規范
| Standard Specification for Lubricant for Installation of Preformed Compression Seals in Concrete Pavements
|
| ASTM D 3079-1994
| 干燥物品用熱密封軟包裝的水蒸氣滲透性的標準試驗方法
| Standard Test Method for Water Vapor Transmission of Flexible Heat-Sealed Packages for Dry Products
|
| ASTM D 3139-1998
| 使用撓性彈性密封件的塑料壓力管用連接件標準規范
| Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals
|
| ASTM D 3212a-1996
| 使用彈性柔性密封料制的塑料排水管和污水管接頭的標準規范
| Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
|
| ASTM D 3406-1995
| 硅酸鹽水泥混凝土路面用彈性體型熱處理的接縫密封膠標準規范
| Standard Specification for Joint Sealant, Hot-Applied, Elastomeric-Type, for Portland Cement Concrete Pavements
|
| ASTM D 3667-2005
| 平板太陽能集熱器用橡膠密封件的標準規范
| Standard Specification for Rubber Seals Used in Flat-Plate Solar Collectors
|
| ASTM D 3771-2003
| 聚集型太陽能加熱器用橡膠密封件的標準規范
| Standard Specification for Rubber Seals Used in Concentrating Solar Collectors
|
| ASTM D 3832-1979
| 太陽能系統中同液體接觸的橡膠密封件規格
| Rubber Seals Contacting Liquids in Solar Energy Systems
|
| ASTM D 3903-2003
| 太陽能系統的熱空氣傳遞用橡膠密封件的標準規范
| Standard Specification for Rubber Seals Used in Air-Heat Transport of Solar Energy Systems
|
| ASTM D 3910-2007
| 灰漿密封的設計、測試和施工的標準實施規程
| Standard Practices for Design, Testing, and Construction of Slurry Seal
|
| ASTM D 4161-2001
| 使用撓性彈性體密封件的"玻璃鋼"(玻璃纖維增強熱固樹脂)管接頭標準規范
| Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe Joints Using Flexible Elastomeric Seals
|
| ASTM D 4866-1988
| 含礦物集料和附加聚合物摻合料的煤焦油瀝青乳化液鋪面密封料攪拌配方的標準性能規范
| Standard Performance Specification for Coal Tar Pitch Emulsion Pavement Sealer Mix Formulations Containing Mineral Aggregates and Optional Polymeric Admixtures
|
| ASTM D 5093-2002
| 使用有密封內環的雙環滲透計現場測量滲透率的標準試驗方法
| Standard Test Method for Field Measurement of Infiltration Rate Using a Double-Ring Infiltrometer with a Sealed-Inner Ring
|
| ASTM D 5094-2004
| 加螺紋或有耳型密封罩容器中液體泄漏總量的標準測試方法
| Standard Test Methods for Gross Leakage of Liquids from Containers with Threaded or Lug-Style Closures
|
| ASTM D 5167-2003
| 熱用接縫及裂紋粘合密封膠和填充物溶化特性評價的標準實施規范
| Standard Practice for Melting of Hot-Applied Joint and Crack Sealant and Filler for Evaluation
|
| ASTM D 5249-1995
| 硅酸鹽水泥混凝土和地瀝青接頭加熱和制冷接縫密封膠襯墊材料的標準規范
| Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints
|
| ASTM D 5329-2004
| 瀝青及硅酸鹽水泥混凝土路面上接縫與裂紋用熱鋪密封料和填充料的標準試驗方法
| Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphaltic and Portland Cement Concrete Pavements
|
| ASTM D 5419-1995
| 螺紋塑料密封箱抗環境應力裂開性能的標準試驗方法
| Standard Test Method for Environmental Stress Crack Resistance (ESCR) of Threaded Plastic Closures
|
| ASTM D 5486/D 5486M-2006
| 箱包裝和密封包裝用的壓敏包裝帶的標準規范
| Standard Specification for Pressure-Sensitive Tape for Packaging, Box Closure, and Sealing
|
| ASTM D 5535-1998
| 與路面接合點和裂紋用現場密封膠相關的標準術語
| Standard Terminology Relating to Formed-in-Place Sealants for Joints and Cracks in Pavements
|
| ASTM D 5570-1994
| 用作外殼密封的膠帶和膠粘劑耐水性標準試驗方法
| Standard Test Method for Water Resistance of Tape and Adhesives Used as Box Closure
|
| ASTM D 5571-1994
| 額定容量不超過60加侖(227公升)的塑料密封頭圓筒的耐環境應力裂開(ESCR)的標準試驗方法
| Standard Test Method for Environmental Stress Crack Resistance (ESCR) of Plastic Tighthead Drums Not Exceeding 60 Gal (227 L) in Rated Capacity
|
| ASTM D 5642-1999
| 密封管道化學兼容性試驗的標準試驗方法
| Standard Test Method for Sealed Tube Chemical Compatibility Test
|
| ASTM D 5657-2007
| 螺紋緊固件用膠粘劑的流體密封能力的標準試驗方法
| Standard Test Method for Fluid Tightness Ability of Adhesives Used on Threaded Fasteners
|
| ASTM D 5749-2001
| 密封和保險用增強和普通紙膠帶的標準規范
| Standard Specification for Reinforced and Plain Gummed Tape for Sealing and Securing
|
| ASTM D 5893-2004
| 硅酸鹽水泥混凝土路面用冷鋪的單一成分、化學固化硅酮接縫密封劑的標準規范
| Standard Specification for Cold Applied, Single Component, Chemically Curing Silicone Joint Sealant for Portland Cement Concrete Pavements
|
| ASTM D 5973-1997
| 用于膨脹節密封的帶鋼封閉邊緣圍欄的彈性帶密封件的標準規范
| Standard Specification for Elastomeric Strip Seals with Steel Locking Edge Rails Used in Expansion Joint Sealing
|
| ASTM D 6396-1999
| 測試T形管上管螺紋密封層的標準試驗方法
| Standard Test Method for Testing of Pipe Thread Sealants on Pipe Tees
|
| ASTM D 6465-1999
| 航空航天和通用膠粘劑和密封劑選擇的標準指南
| Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants
|
| ASTM D 6478-2002
| 測定充氣緩沖物用織物的特殊密封性的標準試驗方法
| Standard Test Method for Determining Specific Packability of Fabrics Used in Inflatable Restraints
|
| ASTM D 6515-2000
| 測定橡膠軸密封件從彎曲復原的標準試驗方法
| Standard Test Method for Rubber Shaft Seals Determination of Recovery From Bending
|
| ASTM D 6546-2000
| 工業液壓液用彈性密封件能力測定的標準試驗方法和建議極限值
| Standard Test Methods for and Suggested Limits for Determining Compatibility of Elastomer Seals for Industrial Hydraulic Fluid Applications
|
| ASTM D 6590/D 6590M-2000
| 密封纖維容器和罐用的壓敏膠帶的標準規范
| Standard Specification for Pressure-Sensitive Tape for Sealing Fiber Containers and Cans
|
| ASTM D 6690a-2006
| 混凝土和瀝青鋪路熱應用連接和裂紋密封劑的標準規范
| Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements
|
| ASTM D 6752-2003
| 用自動真空密封法測量壓實的瀝青混合料的毛體積比重和密度的標準試驗方法
| Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method
|
| ASTM D 6857-2003
| 自動真空密封法測定瀝青鋪面混合料最大比重和密度的標準試驗方法
| Standard Test Method for Maximum Specific Gravity and Density of Bituminous Paving Mixtures Using Automatic Vacuum Sealing Method
|
| ASTM D 6924-2003
| 橋用預制熱塑硫化彈性體密封件的標準規范
| Standard Specification for Preformed Thermoplastic Vulcanizate Elastomeric Joint Seals for Bridges
|
| ASTM D 6946-2003
| 乳化的精制煤焦油的標準規范(公路密封劑、現成品、主要為住宅級)
| Standard Specification for Emulsified Refined Coal-Tar (Driveway Sealer, Ready to Use, Primarily Residential Grade)
|
| ASTM D 7158-2007
| 密封瀝青屋面板的防風用標準試驗方法(上升力/抗上升力方法)
| Standard Test Method for Wind Resistance of Sealed Asphalt Shingles (Uplift Force/Uplift Resistance Method)
|
| ASTM D 7177-2005
| 聚氯乙烯雙軌密封地膜氣道評價的標準規范
| Standard Specification for Air Channel Evaluation of Polyvinyl Chloride (PVC) Dual Track Seamed Geomembranes
|
| ASTM D 7216-2005
| 測定汽車發動機燃油與典型密封人造橡膠兼容性的標準試驗方法
| Standard Test Method for Determining Automotive Engine Oil Compatibility with Typical Seal Elastomers
|
| ASTM E 1068-1985
| 用模擬地熱試液浸漬法測試非金屬密封材料的方法
| Test Method for Testing Nonmetallic Seal Materials by Immersion in a Simulated Geothermal Test Fluid
|
| ASTM E 1069-1985
| 密封應力下地熱和/或高溫操作用聚合密封材料試驗的方法
| Test Method for Testing Polymeric Seal Materials for Geothermal and/or High Temperature Service Under Sealing Stress
|
| ASTM E 1494-1992
| 建筑材料中噴涂或鏝刀涂抹的易碎石棉用密封的標準實施規程
| Standard Practice for Encapsulants for Spray- or Trowel-Applied Friable Asbestos-Containing Building Materials
|
| ASTM E 1612-1994
| 建筑物和停車場結構用預成形建筑壓縮密封件標準規范
| Standard Specification for Preformed Architectural Compression Seals for Buildings and Parking Structures
|
| ASTM E 1720-1995
| 在密封容器二氧化碳的生產試驗中測定有機化合物已有的、最基本的生物分解性的標準試驗方法
| Standard Test Method for Determining Ready, Ultimate, Biodegradability of Organic Chemicals in a Sealed Vessel CO2 Production Test
|
| ASTM E 1773-2005
| 用多硫化合物基密封劑密封剛性壁戰術掩體的標準實施規程
| Standard Practice for Sealing Rigid Wall Tactical Shelters with Polysulfide Based Sealants
|
| ASTM E 1783-1996
| 建筑物和停車場建筑的預制結構密封帶的技術規范
| Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures
|
| ASTM E 1827-1996
| 用風孔門測定建筑物空氣密封性的標準試驗方法
| Standard Test Methods for Determining Airtightness of Buildings Using an Orifice Blower Door
|
| ASTM E 2141-2006
| 密封隔熱玻璃元件上吸收的電鍍鉻涂層穩定性評價的標準試驗方法
| Standard Test Methods for Assessing the Durability of Absorptive Electrochromic Coatings on Sealed Insulating Glass Units
|
| ASTM E 2203-2002
| 壓縮密封件、墊圈、鑲嵌夾具、間隔物和附件的致密熱塑性彈性體的標準規范
| Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories
|
| ASTM E 2240-2006
| 密封絕緣玻璃裝置有吸收力的電致變色覆層在90℃(194°F)時電流-電壓循環穩定性評估的標準試驗方法
| Standard Test Method for Assessing the Current-Voltage Cycling Stability at 90°C (194°F) of Absorptive Electrochromic Coatings on Sealed Insulating Glass Units
|
| ASTM E 2241-2006
| 密封絕緣玻璃裝置有吸收力的電致變色覆層在室溫下的電流-電壓循環穩定性評估的標準試驗方法
| Standard Test Method for Assessing the Current-Voltage Cycling Stability at Room Temperature of Absorptive Electrochromic Coatings on Sealed Insulating Glass Units
|
| ASTM E 2269-2005
| 用氣相色譜法測定密封絕緣玻璃組件中氬濃度的標準試驗方法
| Standard Test Method for Determining Argon Concentration in Sealed Insulating Glass Units using Gas Chromatography
|
| ASTM E 2323-2004
| 用氧氣分析儀測量法計算密封絕緣玻璃裝置中的填充氣體的濃度的標準試驗方法
| Standard Test Method for Calculating the Concentration of Fill Gas in a Sealed Insulating Glass Unit Using Measurements From an Oxygen Analyzer
|
| ASTM E 2336-2004
| 耐火潤滑脂管道密封系統的標準試驗方法
| Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems
|
| ASTM E 2342-2003
| 管道密封劑的耐久檢驗的標準試驗方法
| Standard Test Method for Durability Testing of Duct Sealants
|
| ASTM E 2354-2004
| 密封絕緣玻璃設備內吸收性電致變色涂層的耐用性評估用標準指南
| Standard Guide for Assessing the Durability of Absorptive Electrochromic Coatings within Sealed Insulating Glass Units
|
| ASTM E 546-1988
| 密封絕緣玻璃組件霜點的試驗方法
| Standard Test Method for Frost Point of Sealed Insulating Glass Units
|
| ASTM E 576-1988
| 立式密封絕緣玻璃裝置結霜點的標準試驗方法
| Standard Test Method for Frost Point of Sealed Insulating Glass Units in the Vertical Position
|
| ASTM E 773-1997
| 密封絕熱玻璃裝置的密封耐久性試驗方法
| Standard Test Method for Accelerated Weathering of Sealed Insulating Glass Units
|
| ASTM E 789-1995
| 1.2公升的密封圓筒形容器中粉塵爆炸產生壓力以及壓力升高的速率的標準測試方法
| Standard Test Method for Dust Explosions in a 1.2-Litre Closed Cylindrical Vessel
|
| ASTM F 105-1972
| 58型硼硅酸鹽密封玻璃
| Type 58 Borosilicate Sealing Glass
|
| ASTM F 1052-1997
| 氣密的全密封化工防護套服的加壓試驗
| Standard Test Method for Pressure Testing Vapor Protective Ensembles
|
| ASTM F 112-2000
| 包封襯墊密封性的標準試驗方法
| Standard Test Method for Sealability of Enveloped Gaskets
|
| ASTM F 1157-2004
| 有關安全密封件物理性能分類的標準實施規程
| Standard Practice for Classifying the Relative Performance of the Physical Properties of Security Seals
|
| ASTM F 1158-1994
| 安全密封壓實檢驗和評定
| Standard Guide for Inspection and Evaluation of Tampering of Security Seals
|
| ASTM F 1276-1999
| 復合密封材料的蠕變松弛試驗方法
| Standard Test Method for Creep Relaxation of Laminated Composite Gasket Materials
|
| ASTM F 1315-2000
| 密封墊板材料密度的標準測試方法
| Standard Test Method for Density of a Sheet Gasket Material
|
| ASTM F 1336-2007
| 聚氯乙烯(PVC)密封的下水道管件用標準規范
| Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings
|
| ASTM F 134-1985
| 用氦質譜儀檢漏器測定電子元件密封性的試驗方法
| Test Methods for Determining Hermeticity of Electron Devices with a Helium Mass Spectrometer Leak Detector
|
| ASTM F 1365-1991
| 使用撓性彈性密封材料的地下塑料水管接頭耐水滲透性測試方法
| Standard Test Method for Water Infiltration Resistance of Plastic Underground Conduit Joints Which Use Flexible Elastomeric Seals
|
| ASTM F 14-1980
| 標準玻璃金屬胎圈密封膠的生產和試驗標準實施規程
| Standard Practice for Making and Testing Reference Glass-Metal Bead-Seal
|
| ASTM F 140-1998
| 偏振法測定膨脹特性用的參考玻璃與金屬對接密封材料的制作與試驗
| Standard Practice for Making Reference Glass-Metal Butt Seals and Testing for Expansion Characteristics by Polarimetric Methods
|
| ASTM F 1429-1999
| 使用撓性彈性密封件裝在承接口處的地下塑料管道接頭裝配力的測試方法
| Standard Test Method for Assembly Force of Plastic Underground Conduit Joints That Use Flexible Elastomeric Seals Located in the Bell
|
| ASTM F 144-1980
| 偏振法測定膨脹特性用的參考玻璃金屬夾層密封材料的制作與試驗
| Standard Practice for Making Reference Glass-Metal Sandwich Seal and Testing for Expansion Characteristics by Polarimetric Methods
|
| ASTM F 1466-1999
| 金屬與陶瓷密封用鐵鎳鈷合金的標準規范
| Standard Specification for Iron-Nickel-Cobalt Alloys for Metal-to-Ceramic Sealing Applications
|
| ASTM F 15-2004
| 鐵-鎳-鈷密封合金的標準規范
| Standard Specification for Iron-Nickel-Cobalt Sealing Alloy
|
| ASTM F 1511-2007
| 船泵設施用機械密封件的標準規范
| Standard Specification for Mechanical Seals for Shipboard Pump Applications
|
| ASTM F 1516-2003
| 用熱焊接法(推薦的)密封彈性地板產品接縫的標準實施規范
| Standard Practice for Sealing Seams of Resilient Flooring Products by the Heat Weld Method (when Recommended)
|
| ASTM F 1699-1996
| 無源光纖密封件的標準分類
| Standard Classification for Passive Fiber Optic Seals
|
| ASTM F 1837M-1997
| 熱縮電纜引入密封的標準規范(公制)
| Standard Specification for Heat-Shrink Cable Entry Seals (Metric)
|
| ASTM F 1853-2003
| 測量睡袋密封量的標準試驗方法
| Standard Test Method for Measuring Sleeping Bag Packing Volume
|
| ASTM F 1886-1998
| 用目視檢驗測定醫療包裝密封完整性的標準試驗方法
| Standard Test Method for Determining Integrity of Seals for Medical Packaging by Visual Inspection
|
| ASTM F 19-1964
| 鍍金屬陶瓷密封件抗拉及真空試驗方法
| Test Method for Tension and Vacuum Testing Metalized Ceramic Seals
|
| ASTM F 1921-1998
| 構成撓性腹板密封表面的熱塑聚合物和混合物的熱封強度(熱點焊焊縫)的標準試驗方法
| Standard Test Method for Hot Seal Strength (Hot Tack) of Thermoplastic Polymers and Blends Comprising the Sealing Surfaces of Flexible Webs
|
| ASTM F 2029-2000
| 通過測量密封強度測定撓性網熱密封性能用熔焊的標準實施規范
| Standard Practices for Making Heatseals for Determination of Heatsealability of Flexible Webs as Measured by Seal Strength
|
| ASTM F 204-1976
| 密封鎢絲和鎢條表面裂紋的試驗方法
| Test Method for Surface Flaws in Tungsten Seal Rod and Wire
|
| ASTM F 2054-2007
| 在約束板中使用內部氣體加壓法做軟包裝密封件碎裂測試的標準試驗方法
| Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within Restraining Plates
|
| ASTM F 2155-2001
| 扣鎖或密封用搭扣和其他固定裝置性能的標準規范
| Standard Specification for Performance of Hasps and Other Attachment Devices for Padlocks or Seals
|
| ASTM F 2227-2002
| CO2示蹤氣體法對不密封的及空的醫用包裝盤泄漏性進行無損檢測的標準試驗方法
| Standard Test Method for Non-Destructive Detection of Leaks in Non-sealed and Empty Medical Packaging Trays by CO2 Tracer Gas Method
|
| ASTM F 2378-2005
| 復合薄板材和固態現場成型襯墊材料的密封能力的標準試驗方法
| Standard Test Method for Sealability of Sheet, Composite, and Solid Form-in-Place Gasket Materials
|
| ASTM F 2391-2005
| 使用氦作為示蹤氣體測量包裝和密封完整性的標準試驗方法
| Standard Test Method for Measuring Package and Seal Integrity Using Helium as the Tracer Gas
|
| ASTM F 2414-2004
| 用化學灌漿密封污水道檢查孔的標準規程
| Standard Practice for Sealing Sewer Manholes Using Chemical Grouting
|
| ASTM F 2454-2005
| 用化學灌漿的側向灌漿機法密封測量連接件和主要排污系統管線的標準實施規程
| Standard Practice for Sealing Lateral Connections and lines from the mainline Sewer Systems by the Lateral Packer Method, Using Chemical Grouting
|
| ASTM F 2467-2006
| 運輸用途中用壓力指片(PIF)測量靜態密封壓力的標準實施規程
| Standard Practice for Measuring Static Sealing Pressure Using Pressure-Indicating Film (PIF) in Transportation Applications
|
| ASTM F 2468-2005
| 運輸用硅膠粘劑和密封劑規定的標準分類
| Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications
|
| ASTM F 2524-2006
| 用于運輸?shù)默F(xiàn)場成形墊圈硅酮膠和密封劑的揮發物含量的測定的標準實施規程
| Standard Practice for Determination of Volatile Content for Formed-in-Place Gaskets (FIPG) Silicone Adhesives and Sealants for Transportation Applications
|
| ASTM F 29-1997
| 玻璃與金屬密封裝置用杜美絲
| Standard Specification for Dumet Wire for Glass-to-Metal Seal Applications
|
| ASTM F 30-1996
| 鐵鎳密封合金標準規范
| Standard Specification for Iron-Nickel Sealing Alloys
|
| ASTM F 37-2006
| 襯墊材料密封性的標準試驗方法
| Standard Test Methods for Sealability of Gasket Materials
|
| ASTM F 477-2007
| 連接塑料管用彈性密封件(墊圈)的標準規范
| Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
| ASTM F 511-2004
| 彈性鋪地磚切口(接縫密封性)質量的標準測試方法
| Standard Test Method for Quality of Cut (Joint Tightness) of Resilient Floor Tile
|
| ASTM F 635-1985
| 電子元件及微電子元件封裝用液態熱固密封化合物材料性能試驗的選擇
| Selection of Tests for Material Properties of Liquid Thermoset Encapsulating Compounds for Electronic and Microelectronic Encapsulation
|
| ASTM F 641a-1998
| 可植入的環氧樹脂電子膠囊密封材料標準規范
| Standard Specification for Implantable Epoxy Electronic Encapsulants
|
| ASTM F 677-2004
| 電子和微電子學應用的熱固性密封膠的耐流體和滑脂性能的標準試驗方法
| Standard Test Method for Fluid and Grease Resistance of Thermoset Encapsulating Compounds Used in Electronic and Microelectronic Applications
|
| ASTM F 693-2001
| 使用液體封縫劑密封彈性鋪地薄板制品接縫的標準實施規范
| Standard Practice for Sealing Seams of Resilient Sheet Flooring Products by Use of Liquid Seam Sealers
|
| ASTM F 784-1982
| 校準放射性同位素密封試驗儀的方法
| Test Method for Calibrating Radioisotope Hermetic Test Apparatus
|
| ASTM F 785-1982
| 同位素試驗法測定密封裝置的密封性
| Test Method for Hermeticity of Sealed Devices by a Radioisotope Test
|
| ASTM F 79-1969
| 101型密封玻璃
| Type 101 Sealing Glass
|
| ASTM F 832-1990
| 安全密封件的標準分類
| Standard Classification for Security Seals
|
| ASTM F 866-1984
| 放射性同位素密封試驗用封裝器件封殼衰減系數的測量方法
| Test Method for Measuring the Package Attenuation Coefficient of a Sealed Device for Radioisotope Hermetic Test
|
| ASTM F 88-2007
| 柔性阻擋材料的密封強度用標準試驗方法
| Standard Test Method for Seal Strength of Flexible Barrier Materials
|
| ASTM F 913-2002
| 連接塑料管用熱塑彈性密封件(墊圈)標準規范
| Standard Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
| ASTM F 946-1985
| 制定安全密封控制和衡算計量程序的標準指南
| Standard Guide for Establishing Security Seal Control and Accountability Procedures
|
| ASTM F 97-1972
| 用染料滲透法測定電子器件的密封性
| Determining Hermeticity of Electron Devices by Dye Penetration
|
| ASTM F 979-1986
| 混合微電路組件在封裝前的密封性的試驗方法
| Test Method for Hermeticity of Hybrid Microcircuit Packages Prior to Lidding
|
| IEEE 1107-1996
| 交流電動機使用固定片散繞線圈用密封隔熱系統的評定
| (Thermal evaluation of sealed insulation systems for AC electric machinery employing random-wound stator coils)
|
| IEEE C 57.12.01-1998
| 包括固體澆鑄和/或樹脂密封繞組式在內的干式配電和電力變壓器的一般技術要求
| (General requirements for dry-type distribution and power transformers including those with solid-cast and/or resin-encapsulated windings)
|
| IEEE C 57.12.60-1998
| 固體澆鑄和樹脂密封的電力和配電變壓器用絕緣系統的熱評定試驗程序指南
| (Guide for test procedures for thermal evaluation of insulation systems for solid-cast and resin-encapsulated power and distribution transformers)
|
| UL 157-1996
| 墊圈和密封件
| (Gaskets and seals )
|
| UL 1660-2004
| 液體密封柔性非金屬導(線)管
| (Liquid-tight flexible nonmetallic conduit )
|
| UL 181B-1995
| 用于空氣軟管和空氣連接器的密封系統
| (Closure systems for use with flexible air ducts and air connectors )
|
| UL 2225-1996
| 危險地區用金屬包皮電纜和電纜密封配件
| (Metal-clad cables and cable-sealing fittings for use in hazardous (classified) locations )
|
| UL 2390-2003
| 帶密封片的防風瀝青墻面板的試驗方法
| (Test method for wind resistant asphalt shingles with sealed tabs)
|
| UL 60730-2-4-2003
| 家用和類似用途的電自動控制器.第2部分:密封和半密封式電動壓縮機的電動機熱保護裝置的特殊要求
| (Automatic electrical controls for household and similar use - Part 2: Particular requirements for thermal motor protectors for motor-compressors of hermetic and semi-hermetic type )
|
| UL 963-1997
| 密封、包裝和作標記設備
| (Sealing, wrapping, and marking equipment )
|
| UL 984-1996
| 密封制冷電動機-壓縮機
| (Hermetic refrigerant motor-compressors )
|
| 編號 | 中文名稱 | 英文名稱 |
|---|