| 編號 | 中文名稱 | 英文名稱 |
|---|
| ASME B29.21M-1996 | 水、污水處理設備用700級焊接鋼和鑄造鏈,附件及鏈輪 | (700 class welded steel and cast chains, attachments and sprockets for water and sewage treatment plants) |
| UL 1207-2001 | 危險場所用污水泵 | (Sewage pumps for use in hazardous (classified) locations ) |
| UL 745-4-35-1995 | 由蓄電池供電的污水清潔器特殊要求 | (Particular requirements for battery-operated drain cleaners ) |
| UL 745-2-35-1995 | 污水清潔器特殊要求 | (Particular requirements for drain cleaners ) |
| ANSI/ASTM D5210-1992 | 測定在城市污水管污泥中塑料材料的厭氧生物降解的試驗方法 | Test Method for Determining the Anaerobic Biodegradation of Plastic Materials in the Presence of Municipal Sewer Sludge (08.03) |
| ANSI/ASSE 1051-1998 | 污水管道系統用氣體導入閥 | Air Admittance Valves for Plumbing Drainage Systems |
| ANSI/ASTM D5271-1992 | 活化污泥污水處理系統中利用塑料材料的有氧生物降解的試驗方法 | Test Method for Accessing the Aerobic Biodegradation of Plastic Materials in an Activated Sludge Wastewater-Treatment-System (08.03) |
| ANSI/ASME A112.6.7-2001 | 瓷漆和環氧涂覆的鑄鐵和PVC塑料衛生底板污水池 | Enameled and Epoxy Coated Cast Iron and PVC Plastic Sanitary Floor Sinks |
| ANSI/ASTM D3212-1996 | 軟性人造橡膠密封的排污水塑料管連接件規范 | Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
| ANSI/ASTM F1735-2002 | 修復現有的人可進入的污水管道用PVC襯里的聚氯乙烯(PVC)異型帶材規范 | Specification for Poly (Vinyl Chloride)(PVC) Profile Strip for PVC Liner for Rehabilitation of Existing Man-Entry Sewers and Conduits |
| ANSI/ASTM F1504-2002 | 現有污水管和下水管修復用波紋聚氯乙烯管規范 | Specification for Folded Poly (Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation |
| ANSI/ASTM F810-2001 | 排水和污水處理吸收?qǐng)鲇霉獗诰垡蚁?PE)管規范 | Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields |
| ANSI/ASTM D2729-2003 | 聚氯乙烯(PVC)污水管及管配件規范 | Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ANSI/ASTM D2661-2002 | 丙烯腈-丁二烯-苯乙烯共聚物(ABS)塑料排水管、污水管和通風管和配件規范.表40 | Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ANSI/ASTM D2665-2002 | 聚氯乙烯(PVC)塑料排水管、污水管和通風管及配件規范 | Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ANSI/ASME B29.21M-2003 | 水、污水處理設備用700等級的焊接鋼和鑄造鏈、連接件及鏈輪 | 700 Class Welded Steel and Cast Chains, Attachments, and Sprockets for Water and Sewage Treatment Plants |
| ANSI/AWWA C500-2002 | 排水和污水系統閘門閥 | Gate Valves for Water and Sewage Systems |
| ANSI/ASTM D5813-2004 | 現場固化的熱固性樹脂污水管規范 | Specification for Cured-in-place Thermosetting Resin Sewer Pipe |
| ANSI/ASTM F1947-2004 | 折疊式聚氯乙烯管(PVC)裝進現有污水管和下水管道中的實施規程 | Practice for Installation of Folded Poly(Vinyl Chloride) (PVC) Pipe into Existing Sewers and Conduits |
| ANSI/ASTM F794-2003 | 基于受控內徑的聚氯乙烯(PVC)異型重力沉降污水管及配件規范 | Specification for Poly (Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ANSI/ASTM D3262-2004 | 增強塑料砂漿排污水管規范 | Specification for Reinforced Plastic Mortar Sewer Pipe (08.04) |
| ANSI/ASTM D3754-2004 | 纖維玻璃污水管和工業用壓力管規范 | Specification for Fiberglass Sewer and Industrial Pressure Pipe (08.04) |
| ANSI/ASTM D2751-2005 | 丙烯腈-丁二烯-苯乙烯共聚物(ABS)污水管及配件的規范 | Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings |
| ANSI/ASME A112.18.2-2005 | 衛生管道用污水管配件 | Plumbing Fixture Waste Fittings |
| ANSI/NSF 40(i15)-2005 | 生活污水處理系統 | Residential Wastewater Treatment Systems |
| ANSI/NSF 40(i14)-2005 | 生活污水處理系統 | Residential Wastewater Treatment Systems |
| ANSI/NSF 40(i13r2)-2005 | 生活污水處理系統 | Residential Wastewater Treatment Systems |
| ANSI/NSF 40(i16)-2005 | 生活污水處理系統 | Residential Wastewater Treatment Systems |
| ANSI/ASTM D2321-2005 | 排污水和其它重力流動設備用熱塑性管的地下安裝實施規程 | Practice for Underground Installation of Thermoplastic Pipe for Sewers and other Gravity-Flow Applications |
| ASTM F 585-1994 | 聚乙烯軟管同現有污水管插接 | Standard Practice for Insertion of Flexible Polyethylene Pipe Into Existing Sewers |
| ASTM F 1732-1996 | 聚氯乙烯(PVC)污水管和排水管包括回收PVC材料的標準規范 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer and Drain Pipe Containing Recycled PVC Material |
| ASTM A 862/A 862M-1998 | 瀝青覆層在波紋鋼污水管和排水管上的應用的標準操作規程 | Standard Practice for Application of Asphalt Coatings to Corrugated Steel Sewer and Drainage Pipe |
| ASTM C 913-2002 | 水和污水結構用預制混凝土標準規范 | Standard Specification for Precast Concrete Water and Wastewater Structures |
| ASTM F 2233-2003 | 現有污水管中光纖網絡的安全性、使用權限、建造、義務和風險管理的標準指南 | Standard Guide for Safety, Access Rights, Construction, Liability, and Risk Management for Optical Fiber Networks in Existing Sewers |
| ASTM C924M-1989 | 用低壓空氣試驗法測試混凝土污水管的標準規程 | Standard Practice for Testing Concrete Pipe Sewer Lines by Low-Pressure Air Test Method (Metric) |
| ASTM A 849-2000 | 波紋鋼排水管和污水管用后涂覆鋪面和襯里材料標準規范 | Standard Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe |
| ASTM C 1053-2000 | 排水溝、污水溝和排出口用的硼硅酸鹽玻璃管和配件的標準規范 | Standard Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste, and Vent (DWV) Applications |
| ASTM A 746-2003 | 球墨鑄鐵污水管標準規范 | Standard Specification for Ductile Iron Gravity Sewer Pipe |
| ASTM A 798/A 798M-2001 | 污水管及其它類似用途用工廠制波紋鋼管安裝的標準實施規程 | Standard Practice for Installing Factory-Made Corrugated Steel Pipe for Sewers and Other Applications |
| ASTM D 2680-2001 | 丙烯腈-丁二烯-苯乙烯(ABS)和聚氯乙烯(PVC)共聚物污水管的標準規范 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping |
| ASTM D 3212a-1996 | 使用彈性柔性密封料制的塑料排水管和污水管接頭的標準規范 | Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals |
| ASTM D 5271-2002 | 活性污泥-污水處理系統中測定塑料材料需氧生物降解能力的標準試驗方法 | Standard Test Method for Determining the Aerobic Biodegradation of Plastic Materials in an Activated-Sludge-Wastewater-Treatment System |
| ASTM A 807/A 807M-2002 | 生活污水管及其它類似用途安裝波紋鋼板結構管道的標準實施規范 | Standard Practice for Installing Corrugated Steel Structural Plate Pipe for Sewers and Other Applications |
| ASTM D 2661-2002 | 丙烯腈-丁二烯-苯乙烯共聚物(ABS)塑料排水管、污水管和通氣管及其管件.附表40 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM D 4282-2002 | 用微擴散法測定水和污水中游離氰化物的標準試驗方法 | Standard Test Method for Determination of Free Cyanide in Water and Wastewater by Microdiffusion |
| ASTM C 969M-2002 | 安裝的預制混凝土污水管道的表面滲入和滲出的驗收檢驗的標準實施規程(米制) | Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines [Metric] |
| ASTM C 969-2002 | 安裝的預制混凝土污水管道的表面滲入和滲出的驗收檢驗的標準實施規程 | Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines |
| ASTM C 924M-2002 | 低壓空氣試驗法測試混凝土污水管道標準實施規程(米制) | Standard Practice for Testing Concrete Pipe Sewer Lines by Low-Pressure Air Test Method (Metric) |
| ASTM C 924-2002 | 低壓空氣試驗法測試混凝土污水管道的標準實施規程 | Standard Practice for Testing Concrete Pipe Sewer Lines by Low-Pressure Air Test Method |
| ASTM C 923M-2002 | 鋼筋混凝土制檢查孔、污水管和橫向排水溝間彈性接頭的標準規范(米制) | Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals [Metric] |
| ASTM C 923-2002 | 鋼筋混凝土制檢查孔、污水管和橫向排水溝間彈性接頭的標準規范 | Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes and Laterals |
| ASTM F 1504-2002 | 現有污水管和下水管修復用折疊式聚氯乙烯管的標準規范 | Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation |
| ASTM D 2729-2003 | 聚氯乙烯(PVC)污水管及配件標準規范 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM F 794-2003 | 以受控內徑為基準的聚氯乙烯(PVC)異型重力污水管及配件的標準規范 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM D 5813-2004 | 現場硫化固定的熱固性樹脂污水管系統的標準規范 | Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems |
| ASTM F 628-2006 | 有泡沫填充料的丙烯腈-丁二烯-苯乙烯共聚物(ABS)塑料雨水管、污水管和通風管道標準規范.表40 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core |
| ASTM C 507Mb-2005 | 鋼筋混凝土制橢圓形排水管、雨水管和污水管的標準規范(米制) | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe [Metric] |
| ASTM C 1478M-2003 | 加筋混凝土排暴雨污水結構、管道和橫向排水溝間的暴雨排水溝彈性連接件標準規范 | Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals [Metric] |
| ASTM C 564a-2003 | 鑄鐵污水管和配件用橡膠墊圈的標準規范 | Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe and Fittings |
| ASTM C 1103M-2003 | 已安裝的預制混凝土污水管線的接頭驗收標準規程(米制) | Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines [Metric] |
| ASTM C 1103-2003 | 已安裝的預制混凝土污水管線的接頭驗收試驗的標準規程 | Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines |
| ASTM C 506a-2005 | 鋼筋混凝土制拱形排水管、雨水管和污水管的標準規范 | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 507a-2005 | 鋼筋混凝土制橢圓形排水管、雨水管和污水管的標準規范 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 1540-2004 | 重型有套連接器連接無轂鑄鐵污水管道和管配件的標準規范 | Standard Specification for Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings |
| ASTM C 1111-2004 | 感應耦合等離子體原子發射光譜法測定污水流中元素的標準試驗方法 | Standard Test Method for Determining Elements in Waste Streams by Inductively Coupled Plasma-Atomic Emission Spectroscopy |
| ASTM D 3754-2004 | 玻璃纖維增強熱固性樹脂污水壓力管和工業壓力管的標準規范 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe |
| ASTM D 3262-2004 | 玻璃纖維增強熱固性樹脂污水管標準規范 | Standard Specification for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer Pipe |
| ASTM C 655M-2004 | 鋼筋混凝土D型承重涵管、雨水管和污水管的標準規范(米制) | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe [Metric] |
| ASTM C 655-2004 | 鋼筋混凝土D型承重涵管、雨水管和污水管的標準規范 | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 985M-2004 | 規定強度的無鋼筋混凝土涵管、雨水管和污水管(米制)的標準規范 | Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe [Metric] |
| ASTM C 506Ma-2005 | 鋼筋混凝土制拱形排水管、雨水管和污水管的標準規范(米制) | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe [Metric] |
| ASTM F 949a-2006 | 光滑內壁聚氯乙烯(PVC)波紋污水管和配件的標準規范 | Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings |
| ASTM D 3034-2006 | PSM型聚氯乙烯(PVC)污水管和配件的標準規范 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM C 1563-2004 | 衛生排水、廢棄物、通風和暴雨管設施用與襯套窩接式鑄鐵污水管和配件相連接用墊圈的標準試驗方法 | Standard Test Method for Gaskets for Use in Connection with Hub and Spigot Cast Iron Soil Pipe and Fittings for Sanitary Drain, Waste, Vent, and Storm Piping Applications |
| ASTM C 1417M-2004 | 直接設計的鋼筋混凝土污水管、雨水管和涵管的生產標準規范(米制) | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric) |
| ASTM C 1417-2004 | 直接設計的鋼筋混凝土污水管、雨水管和涵管的生產標準規范 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
| ASTM C 985-2004 | 規定強度的無鋼筋混凝土涵管、雨水管和污水管的標準規范 | Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe |
| ASTM F 2414-2004 | 用化學灌漿密封污水道檢查孔的標準規程 | Standard Practice for Sealing Sewer Manholes Using Chemical Grouting |
| ASTM D 2751-2005 | 丙烯腈-丁二烯-苯乙烯共聚物(ABS)污水管和配件的標準規范 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings |
| ASTM A 888-2005 | 污水、雨水、廢物和通風管道用無凸口鑄鐵污水管及配件的標準規范 | Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications |
| ASTM C 1244a-2005 | 回填之前利用負壓(真空)試驗的混凝土污水管檢查孔的標準試驗方法 | Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill |
| ASTM C 76Mb-2005 | 鋼筋混凝土制涵管、雨水管和污水管的標準規范（米制） | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe [Metric] |
| ASTM C 428-2005 | 石棉水泥無壓污水管道的標準規范 | Standard Specification for Asbestos-Cement Nonpressure Sewer Pipe |
| ASTM C 32-2005 | 污水管和人孔用磚(粘土或頁巖制)的標準規范 | Standard Specification for Sewer and Manhole Brick (Made From Clay or Shale) |
| ASTM F 679-2006 | 大直徑聚氯乙烯（PVC）塑料重力污水管和配件的標準規范 | Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings |
| UL 1086-1996 | 家用垃圾壓實器 | (Household trash compactors ) |
| ANSI/NSF 21-1996 | 熱塑性塑料垃圾容器 | Thermoplastic Refuse Containers |
| ANSI/NSF 13-2001 | 垃圾壓實器和壓實系統 | Refuse Compactors and Compactor Systems |
| ANSI/NSF 13(i2)-2005 | 垃圾處理機和處理系統 | Refuse processors and processing systems |
| ANSI/UL 1086-2005 | 家用垃圾壓實器的安全標準 | Standard for Safety for Household Trash Compactors |
| ANSI Z245.1-1999 | 垃圾的收集、處理和處置設備.移動式垃圾收集和壓實設備.安全要求 | Refuse Collection, Processing, and Disposal Equipment - Mobile Refuse Collection and Compaction Equipment - Safety Requirements |
| ANSI Z245.30-1999 | 垃圾的收集、處理和處置設備.垃圾箱.安全要求 | Refuse Collection, Processing, and Disposal Equipment - Waste Containers - Safety Requirements |
| ANSI Z245.60-1999 | 垃圾收集、處理和處置設備.垃圾箱.兼容尺寸 | Refuse Collection, Processing, and Disposal Equipment - Waste Containers - Compatibility Dimensions |
| ASTM D 6523-2000 | 垃圾堆積場的代用日掩蓋物的評價和選定的標準指南 | Standard Guide for Evaluation and Selection of Alternative Daily Covers (ADCs) for Sanitary Landfills |
| 編號 | 中文名稱 | 英文名稱 |
|---|