| 編號 | 中文名稱 | 英文名稱 |
|---|
| DL/T 695-1999
| 電站鋼制對焊管件
| ()
|
| DL/T 935-2005
| 鋼塑復合管和管件
| ()
|
| GB 15558.2-2005
| 燃?xì)庥寐竦鼐垡蚁?PE)管道系統第2部分:管件
| Buried Polyethylene(PE)piping systems for the supply of gaseous fuels Part 2:Fittings
|
| GB/T 12459-2005
| 鋼制對焊無縫管件
| Steel butt-welding seamless pipe fittings
|
| GB/T 12772-1999
| 排水用柔性接口鑄鐵管及管件
| Cast iron pipes and fittings with flexible joint sewerage
|
| GB/T 13021-1991
| 聚乙烯管材和管件炭黑含量的測定熱失重法
| Determination for the carbon black content of polyethylene pipes and fittings by calcination and pyrolysis
|
| GB/T 13295-2003
| 水及燃?xì)夤艿烙们蚰T鐵管、管件和附件
| Ductile iron pipes，fittings and accessories for water or gas applications
|
| GB/T 13401-2005
| 鋼板制對焊管件
| Steel plate butt-welding pipe fittings
|
| GB/T 13663.2-2005
| 給水用聚乙烯(PE)管道系統第2部分:管件
| Polyethylene(PE)pipings systems for water supply Part 2:Fittings
|
| GB/T 14383-1993
| 鍛鋼制承插焊管件
| Forged steel socket welding pipe fittings
|
| GB/T 14626-1993
| 鍛鋼制螺紋管件
| Forged steel threaded pipe fittings
|
| GB/T 15819-2006
| 灌溉用聚乙烯(PE)管材由插入式管件引起環境應力開裂敏感性的試驗方法和技術要求
| Polyethylene (PE) pipes for irrigation laterals - Susceptibility to envionmental stress cracking induced by insert-type fittings - Test method and specification
|
| GB/T 15820-1995
| 聚乙烯壓力管材與管件連接的耐拉拔試驗
| Test of resistance to pull out ofjoints between polyethylene (PE) pressure pipes and fittings
|
| GB/T 17185-1997
| 鋼制法蘭管件
| Steel pipe fittings for flanged joint
|
| GB/T 17241.1-1998
| 鑄鐵管法蘭類型
| Synoptic table for cast iron pipe flanges
|
| GB/T 17241.2-1998
| 鑄鐵管法蘭蓋
| Cast iron pipe blank flanges
|
| GB/T 17241.3-1998
| 帶頸螺紋鑄鐵管法蘭
| Hubbed threaded cast iron pipe flanges
|
| GB/T 17241.4-1998
| 帶頸平焊和帶頸承插焊鑄鐵管法蘭
| Hubbed slip-on-welding and hubbed socket welding cast iron pipe flanges
|
| GB/T 17241.5-1998
| 管端翻邊帶頸松套鑄鐵管法蘭
| Loose hubbed cast iron pipe flanges for lapped pipe end
|
| GB/T 17241.6-1998
| 整體鑄鐵管法蘭
| Integral cast iron pipe flanges
|
| GB/T 17241.7-1998
| 鑄鐵管法蘭技術條件
| Specifications for cast iron pipe flanges
|
| GB/T 17391-1998
| 聚乙烯管材與管件熱穩定性試驗方法
| Test method for thermal stability of polyethylene pipes and fittings
|
| GB/T 17456-1998
| 球墨鑄鐵管外表面噴鋅涂層
| Ductile iron pipes--External zinc-spray coating
|
| GB/T 17457-1998
| 球墨鑄鐵管水泥砂漿離心法襯層一般要求
| Ductile iron pipes--Centrifugal cement mortar lining--General requirements
|
| GB/T 17458-1998
| 球墨鑄鐵管水泥砂漿離心法襯層新拌砂漿的成分檢驗
| Ductile iron pipes--Centrifugal cement mortar lining--Composition controls of freshly appliedmortar
|
| GB/T 17459-1998
| 球墨鑄鐵管瀝青涂層
| Ductile iron pipes--Bitumen coating
|
| GB/T 18251-2000
| 聚烯烴管材、管件和混配料中顏料或炭黑分散的測定方法
| Method for the assessment of pigment or carbon black dispersion in polyolefin pipes，fittings and compounds
|
| GB/T 18474-2001
| 交聯聚乙烯(PE-X)管材與管件交聯度的試驗方法
| Pipes and fittings made of crosslinked polyethylene(PE-X)--Estimation of the degree of crosslinkingby determination of the gel content
|
| GB/T 18475-2001
| 熱塑性塑料壓力管材和管件用材料分級和命名總體使用(設計)系數
| Thermoplastics materials for pipes and fittings for pressure applications classification and designation--Overall service(design) coefficient
|
| GB/T 18742.3-2002
| 冷熱水用聚丙烯管道系統第3部分:管件
| Polypropylene piping systems for hot and cold water installations--Part 3:Fittings
|
| GB/T 18991-2003
| 冷熱水系統用熱塑性塑料管材和管件
| Thermoplastics pipes and fittings forhot and cold water systems
|
| GB/T 18993.3-2003
| 冷熱水用氯化聚氯乙烯(PVC-C)管道系統第3部分: 管件
| Chlorinated poly(Vinyl chloride) piping systems for hot and cold water installations--Part 3: Fittings
|
| GB/T 18998.3-2003
| 工業用氯化聚氯乙烯(PVC-C)管道系統第3部分: 管件
| Chlorinated poly(vinyl chloride)(PVC-C) piping systems for industrial applications--Part 3: Fittings
|
| GB/T 19228.1-2003
| 不銹鋼卡壓式管件
| Stainless steel press-fittings
|
| GB/T 19228.2-2003
| 不銹鋼卡壓式管件連接用薄壁不銹鋼管
| Light gauge stainless steel pipes for stainless steel press-fittings
|
| GB/T 19228.3-2003
| 不銹鋼卡壓式管件用橡膠O形密封圈
| O-rings for stainless steel press-fittings
|
| GB/T 19278-2003
| 熱塑性塑料管材、管件及閥門通用術語及其定義
| General terms and their definitions of thermoplastic pipes，fittings and valves
|
| GB/T 19473.3-2004
| 冷熱水用聚丁烯(PB)管道系統第3部分:管件
| Polybutylene(PB) piping systems for hot and cold water installations--Part 3:Fittings
|
| GB/T 19712-2005
| 塑料管材和管件聚乙烯(PE)鞍形旁通抗沖擊試驗方法
| Plastics pipes and fittingsPolyethylene(PE) tapping tees Test method for impact resistance
|
| GB/T 19806-2005
| 塑料管材和管件聚乙烯電熔組件的擠壓剝離試驗
| Plastics pipes and fittings Crushing decohesion test for polyethylene(PE)electrofusion assemblies
|
| GB/T 19807-2005
| 塑料管材和管件聚乙烯管材和電熔管件組合試件的制備
| Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene(PE)pipe and an electrofusion fitting
|
| GB/T 19808-2005
| 塑料管材和管件公稱外徑大于或等于90mm的聚乙烯電熔組件的拉伸剝離試驗
| Plastics pipes and fittings Peel decohesion test for polyethylene(PE)electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
|
| GB/T 19809-2005
| 塑料管材和管件聚乙烯(PE)管材/管材或管材/管件熱熔對接組件的制備
| Plastics pipes and fittings-Preparation of polyethylene(PE)pipe/pipe or pipe/fitting test piece assemblies by butt fusion
|
| GB/T 19810-2005
| 聚乙烯(PE)管材和管件熱熔對接接頭拉伸強度和破壞形式的測定
| Polyethylene(PE)pipe and fittings-Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
|
| GB/T 19993-2005
| 冷熱水用熱塑性塑料管道系統 管材管件組合系統熱循環試驗方法
| Thermoplastics piping systems for hot and cold water supply-Test method for the resiance of pipes and fittings mounted assemblies to thermal cycling
|
| GB/T 20201-2006
| 灌溉用聚乙烯(PE)壓力管機械連接管件
| Mechanical joint fittings for use with polyethylene pressure pipes for irrigation purposes
|
| GB/T 20207.2-2006
| 丙烯腈－丁二烯－苯乙烯（ABS）壓力管道系統第2部分：管件
| Acrylonitrile-butadiene-styrene (ABS) pressure piping systems - Part 2: fittings
|
| GB/T 20674.1-2006
| 塑料管材和管件 聚乙烯系統熔接設備 第1部分：熱熔對接
| Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 1：Butt fusion
|
| GB/T 20674.2-2006
| 塑料管材和管件 聚乙烯系統熔接設備 第2部分：電熔連接
| Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 2: Electrofusion
|
| GB/T 3287-2000
| 可鍛鑄鐵管路連接件
| Malleable cast iron pipe fittings
|
| GB/T 3420-1982
| 灰口鑄鐵管件
| Gray iron castigs for pipe fittings
|
| GB/T 3422-1982
| 連續鑄鐵管
| Cast-iron pressure pipe made by continuous casting process
|
| GB/T 5836.2-2006
| 建筑排水用硬聚氯乙烯（PVC-U）管件
| Unplasticized poly(vinyl chloride) (PVC-U) fittings for soil and waste inside buildings
|
| GB/T 6483-1986
| 柔性機械接口灰口鑄鐵管
| Soft mechanical joint grey cast iron pipe
|
| GB/T 6567.3-1986
| 管路系統的圖形符號管件
| Graphical symbols for piping systems--Piping accessories
|
| GB/T 6567.5-2003
| 管路系統的圖形符號管路、管件和閥門等圖形符號的軸測圖畫法
| Graphical symbols for piping systems--Axonometric representation of graphical symbols for piping，piping accessories and valves etc
|
| GB/T 8714-1988
| 梯唇型橡膠圈接口鑄鐵管
| Grey cast iron pipes with rubber ring of ladder-lip-shaped
|
| GB/T 8715-1988
| 柔性機械接口鑄鐵管件
| Soft mechanical joint grey cast iron fittings
|
| GB/T 8801-1988
| 硬聚氯乙烯 (PVC-U) 管件墜落試驗方法
| Test method for unplasticized (PVC-U) fittings by falling
|
| GB/T 8802-2001
| 熱塑性塑料管材、管件維卡軟化溫度的測定
| Thermoplastics pipes and fitting--Determination of vicat softening temperature
|
| GB/T 8803-2001
| 注射成型硬質聚氯乙烯(PVC-U)、氯化聚氯乙烯(PVC-C)、丙烯腈-丁二烯-苯乙烯三元共聚物(ABS)和丙烯腈-苯乙烯
| Injection-moulded unplasticized poly(vinyl chloride)(PVC-U)，chlorinated poly(vinyl chloride)(PVC-C)，acrylonitrile butadiene-styrene(ABS)and acrylonitrile-styrene-acrylester(ASA)fittings--Hot oven test method
|
| HG/T 20538-1992
| 襯塑（PP、PE、PVC）鋼管和管件
| ()
|
| HG/T 20539-1992
| 增強聚丙烯（FRPP）管子和管件
| ()
|
| HG/T 2128-1991
| 耐酸酚醛塑料制化工設備、管、管件技術條件
| ()
|
| HG/T 21501-1993
| 襯膠鋼管和管件
| ()
|
| HG/T 21561-1994
| 丙烯腈—丁二烯—苯乙烯（ABS）管和管件
| ()
|
| HG/T 21562-1994
| 襯聚四氟乙烯鋼管和管件
| ()
|
| HG/T 21579-1995
| 聚丙烯/玻璃鋼（PP/FRP）復合管及管件
| ()
|
| HG/T 21631-1990
| 鋼制有縫對焊管件
| ()
|
| HG/T 21633-1991
| 玻璃鋼管和管件
| ()
|
| HG/T 21634-1988
| 鍛鋼承插焊管件
| ()
|
| HG/T 21635-1987
| 碳鋼、低合金鋼無縫對焊管件
| ()
|
| HG/T 21636-1987
| 玻璃鋼/聚氯乙烯（FRP/PVC)復合管和管件
| ()
|
| HG/T 2435-1993
| 玻璃管和管件
| ()
|
| HG/T 2436-1993
| 玻璃管和管件耐壓試驗方法
| ()
|
| HG/T 2437-2006
| 塑料襯里復合鋼管和管件
| Steel pipes and fitting lined with plastic
|
| HG/T 3691-2001
| 工業用鋼骨架聚乙稀塑料復合管件
| ()
|
| HG/T 3705-2003
| 金屬網聚四氟乙烯復合管與管件
| ()
|
| HG/T 3707-2003
| 工業用孔網鋼骨架聚乙烯復合管件
| ()
|
| HG/T 3731-2004
| 玻璃纖維增強聚氯乙烯復合管和管件
| ()
|
| JB/T 1308.2-1999
| PN250MPa閥門、管件和緊固件技術條件
| ()
|
| JB/T 2768-1992
| PN16.0～32.0MPa 管子、管件、閥門端部尺寸
| ()
|
| JB/T 2778-1992
| PN16.0～32.0MPa 管件和緊固件溫度標記
| ()
|
| JB/T 450-1992
| PN16.0～32.0MPa 鍛造角式高壓閥門、管件、緊固件 技術條件
| ()
|
| JB/T 5976.1-1992
| PNO.6MPa可鍛鑄鐵管法蘭蓋
| ()
|
| JB/T 5976.2-1992
| PN1.0MPa可鍛鑄鐵管法蘭蓋
| ()
|
| JB/T 5976.3-1992
| PN1.6MPa可鍛鑄鐵管法蘭蓋
| ()
|
| JB/T 5976.4-1992
| PN2.5MPa可鍛鑄鐵管法蘭蓋
| ()
|
| JB/T 5976.5-1992
| PN4.0MPa可鍛鑄鐵管法蘭蓋
| ()
|
| JB/T 5982-1992
| 可鍛鑄鐵管法蘭用石棉橡膠墊片
| ()
|
| JB/T 6308-2000
| 離心鑄管機 技術條件
| ()
|
| JB/T 7525-1994
| 聚丙烯 玻璃纖維增強塑料復合管和管件
| ()
|
| JB/T 7870-1997
| 噴灌用金屬薄壁管及管件
| ()
|
| QB/T 2003-1994
| 食品工業用不銹鋼對縫焊接管件
| ()
|
| QB/T 2480-2000
| 建筑用硬聚氯乙烯(PVC-U)雨落水管材及管件
| ()
|
| QB/T 3802-1999
| 化工用硬聚氯乙烯管件
| Unplasticized polyvinyl chloride(PVC)fittings for chemical industry
|
| QC/T 669-2000(2005)
| 汽車空調(HFC-134a)用管接頭和管件
| ()
|
| SB/T 10355-2002
| 制冷系統和熱泵—軟管件、隔振器和膨脹接頭—要求、設計與安裝
| ()
|
| SY/T 0510-1998(2006年確認)
| 鋼制對焊管件
| ()
|
| SY/T 0518-2002
| 油氣管道鋼制對焊管件設計規程
| ()
|
| SY/T 6266-2004
| 低壓玻璃纖維管線管和管件
| ()
|
| SY/T 6701-2007
| 增強MC尼龍管和尼龍—鋼復合管及管件
| Reinforced MC nylon pipes and nylon-steel composite pipes and fittings
|
| YB/T 177-2000(2006年確認)
| 連續鑄造球墨鑄鐵管
| ()
|
| YS/T 583-2006
| 熱鍛水暖管件用黃銅棒
| ()
|
| YS/T 584-2006
| 電極材料用鉻、鋯青銅管件
| ()
|
| 編號 | 中文名稱 | 英文名稱 |
|---|