| 編號 | 中文名稱 | 英文名稱 |
|---|
| ANSI C78.1420-2001
| 電燈.縮微膠片投影燈.GX5.3基座的2英寸(50mm)內二色性涂層反射邊絕的標準鹵鎢燈
| Electric Lamps - Microfilm Projection Lamps-Two-inch (51mm) Dichroic Coated Integral Reflector, Rim Reference, Tungsten Halogen Lamps with GX5.3 Bases
|
| ANSI C78.1434-2001
| 帶GX7.9基座的冷凝二色性涂層整體反光側釘?shù)柠u鎢投射燈
| Condensing Dichroic Coated Integral Reflector Side Pin Tungsten Halogen Projection Lamps with GX7.9 Bases
|
| ANSI/ASTM A937/A 937M-2001
| 利用兩個相鄰試驗表面測定絕緣涂層層間電阻的方法
| Test Method for Determining Interlaminar Resistance of Insulating Coatings Using Two Adjacent Test Surfaces
|
| ANSI/ASTM A976-1997
| 復合絕緣涂層絕緣能力和應用的分類
| Classification of Insulating Coatings by Composition, Relative Insulating Ability and Application
|
| ANSI/ASTM B735-1995
| 硝酸蒸氣測試金屬基體上金涂層孔隙率的方法
| Test Method for Porosity in Gold Coatings on Metal Substrates by Nitric Acid Vapor
|
| ANSI/ASTM B741-1995
| 紙電譜法測量金屬基體上金涂層孔隙率的方法
| Test Method for Porosity in Gold Coatings on Metal Substrates by Paper Electrography
|
| ANSI/ASTM B750-1999
| 熱浸涂層鋅5%鋁混合稀土合金(UNS Z38510)鑄錠規范
| Specification for Zinc-5 % Aluminum-Mischmetal Alloy (UNS Z38510) in Ingot Form for Hot-Dip Coatings
|
| ANSI/ASTM B798-1995
| 凝膠體電譜法測定金屬基物上金或鈀涂層孔隙度的方法
| Test Method for Porosity in Gold or Palladium Coatings on Metal Substrates by Gel-Bulk Electrography
|
| ANSI/ASTM D1458-2001
| 電絕緣用完全硫化硅橡膠涂層玻璃布與玻璃帶試驗方法
| Test Methods for Fully Cured Silicone Rubber-Coated Glass Fabric and Tapes for Electrical Insulation
|
| ANSI/ASTM D2534-1988
| 蠟涂層的動摩擦系數的試驗方法(05.01)
| Coefficient of Kinetic Friction for Wax Coatings, Method of Test for (05.01)
|
| ANSI/ASTM D3214-1997
| 電絕緣涂料粉末及其涂層試驗方法
| Test Methods for Coating Powders and Their Coatings Used for Electrical Insulation
|
| ANSI/ASTM D3236-1988
| 熱熔性膠粘劑和涂層材料的表觀密度的試驗方法(05.02)
| Apparent Viscosity of Hot Melt Adhesives and Coating Materials, Method of Test for (05.02)
|
| ANSI/ASTM D3521-1986
| 波紋紙板上表面蠟涂層的試驗方法
| Test Method for Surface Wax Coating on Corrugated Board
|
| ANSI/ASTM D3708-1988
| 在涂層加工中使用的蠟的重量的試驗(05.03)
| Weight of Wax Applied During Curtain Coating Operation, Test for (05.03)
|
| ANSI/ASTM D4917-1997
| 用水平面法測量非涂層書寫印刷紙動態和靜態摩擦系數的方法
| Test Method for Coefficient of Static and Kinetic Friction of Uncoated Writing and Printing Paper by Use of the Horizontal Plane Method
|
| ANSI/ASTM D4918-1997
| 用傾斜面法測試無涂層書寫紙和印刷紙靜磨擦系數的試驗方法
| Test Method for Coefficient of Static Friction of Uncoated Writing and Printing Paper by Use of the Inclined Plane Method
|
| ANSI/ASTM F1916-1998
| 拘役用帶涂層鏈節柵欄結構和圓柱的鏈節柵欄系統選用規范
| Specifications for Selecting Chain Link Barrier Systems with Coated Chain Link Fence Fabric and Round Posts for Detention Applications
|
| ANSI/ASTM F2016-2000
| 規定船體結構、舾裝設備和涂層的質量要求慣例
| Practice for Establihsing Shipbuiling Quality Requirements for Hull Structure, Outfitting and Coatings
|
| ANSI/AWS A4.4M-2001
| 焊接助熔劑和電焊條助熔劑涂層含水量標準測定程序
| Standard Procedures for Determination of Moisture Content of Welding Fluxes and Welding Electrode Flux Coverings
|
| ANSI/AWWA C116/A 21.16-2003
| 供水設備用球墨鑄鐵和灰鐵配件的內外表面的防護熔融膠合環氧涂層
| Protective Fusion-Bonded Epoxy Coatings for the Interior and Exterior Surfaces of Ductile-Iron and Gray-Iron Fittings for Water Supply Service
|
| ANSI/AWWA C203-2002
| 給水鋼管煤焦油保護涂層和內襯.熱用搪瓷和膠帶
| Coal-Tar Protective Coatings and Linings for Steel Water Pipelines - Enamel and Tape - Hot-Applied
|
| ANSI/AWWA C203a-1999
| 鋼制供水管道的煤焦油保護涂層和內襯標準.搪瓷和膠帶.熱水
| Standard for Coal-Tar Protective Coatings and Linings for Steel Water Pipelines - Enamel and Tape - Hot Applied
|
| ANSI/AWWA C205-2007
| 商用4英寸和4英寸以上鋼水管的水泥灰漿保護襯和涂層
| Cement-Mortar Protective Lining and Coating for Steel Water Pipe - 4 in and Larger - Shop Applied
|
| ANSI/AWWA C209-2007
| 鋼水管用特殊部件、連接件和配件的外部用低溫磁帶涂層
| Cold-Applied Tape Coatings for the Exterior of Special Sections, Connections, and Fittings for Steel Water Pipelines
|
| ANSI/AWWA C210-2003
| 鋼制水管的內外層用液體環氧樹脂涂層系統
| Liquid-Epoxy Coating Systems for the Interior and Exterior of Steel Water Pipelines
|
| ANSI/AWWA C213-2001
| 給水鋼管的內、外層熔化粘結環氧涂層
| Fusion-Bonded Epoxy Coating for the Interior and Exterior of Steel Water Pipelines
|
| ANSI/AWWA C213a-2002
| 鋼制水管內外的熔融膠合環氧樹脂涂層
| Fusion-Bonded Epoxy Coating for the Interior and Exterior of Steel Water Pipelines
|
| ANSI/AWWA C215-2004
| 鋼制水管的外層用擠壓聚烯烴涂層
| Extruded Polyolefin Coatings for the Exterior of Steel Water Pipelines
|
| ANSI/AWWA C216-2007
| 給水鋼管用專用部件、連接件和配件外部可熱收縮交聯的聚烯烴涂層
| Heat-Shrinkable Cross-Linked Polyolefin Coatings for the Exterior of Special Sections, Connections, and Fittings for Steel Water Pipelines
|
| ANSI/AWWA C222-1999
| 鋼水管和配件聚氨基甲酸乙酯內或外涂層
| Polyurethane Coatings for the Interior and Exterior of Steel Water Pipe and Fittings
|
| ANSI/AWWA C224-2007
| 鋼水管、連接件、配件和特殊部件的內部和外部用尼龍11基聚酰胺涂層系統
| Nylon-11-Based Polyamide Coating System for the Interior and Exterior of Steel Water Pipe, Connections, Fittings, and Special Sections
|
| ANSI/AWWA C550-2005
| 閥門和給水栓用防護性內部涂層
| Protective Interior Coatings for Valves and Hydrants
|
| ANSI/AWWA D102-2006
| 涂層的鋼制儲水箱
| Coating Steel Water - Storage Tanks
|
| ANSI/EIA 455-55A-1986
| 光纖涂層幾何尺寸的測量方法
| Coating Geometry of Optical Fibers, Methods for Measuring the
|
| ANSI/EIA-364-48A-2006
| 測量電器連接器件的金屬涂層厚度的試驗程序
| Metallic Coating Thickness Measurement of Contacts Test Procedure for Electrical Connectors
|
| ANSI/EIA/TIA 455-173-1990
| 用光纖側面觀測法測量涂層幾何尺寸
| Coating Geometry Measurement for Optical Fiber Side View Method
|
| ANSI/IEEE 1523-2002
| 戶外陶瓷絕緣子用室溫硫化硅橡膠涂層的應用、維護和評價指南
| Guide for the Application, Maintenance, and Evaluation of Room Temperature Vulcanizing (RTV) Silicone Rubber Coatings for Outdoor Ceramic Insulators
|
| ANSI/NFPA 703-2006
| 建筑材料用阻燃處理木材和阻燃涂層標準
| Standard for Fire-Retardant Treated Wood and Fire-Retardant Coatings for Building Materials
|
| ANSI/TIA-455-173-1990
| 光纖側面檢查法采用的涂層幾何形狀測量
| Coating Geometry Measurement for Optical Fiber Side View Method
|
| ANSI/TIA-455-178-B-2003
| FOTP-178 IEC 60793-1-32 光學纖維.第1-32部分:測量方法和試驗規程.涂層可剝離性
| FOTP-178 IEC 60793-1-32 Optical Fibers - Part 1-32: Measurement Methods and Test Procedures - Coating Stripability
|
| ANSI/TIA-455-195-A-2003
| 光學纖維涂層的幾何學測量.FOTP195
| Coating Geometry Measurement for Optical Fiber - FOTP195
|
| ANSI/TIA/EIA 455-195-2000
| 光纖涂層的幾何量測量.FOTP195
| Coating Geometry Measurement for Optical Fiber - FOTP195
|
| ANSI/UL 1715-2003
| 內部涂層材料燃燒試驗的安全標準
| Standard for Safety for Fire Test of Interior Finish Material
|
| ASTM A 121-2007
| 金屬涂層碳素鋼刺鋼絲的標準規范
| Standard Specification for Metallic-Coated Carbon Steel Barbed Wire
|
| ASTM A 308/A 308M-2006
| 經熱浸工藝涂層的鍍鉛錫(鉛錫合金)鐵薄板標準規范
| Standard Specification for Steel Sheet, Terne (Lead-Tin Alloy) Coated by the Hot-Dip Process
|
| ASTM A 630-2003
| 電鍍錫薄板錫涂層重量測定的標準試驗方法
| Standard Test Methods for Determination of Tin Coating Weights for Electrolytic Tin Plate
|
| ASTM A 754/A 754M-2006
| X射線熒光涂層厚度的標準試驗方法
| Standard Test Method for Coating Weight (Mass) of Metallic Coatings on Steel by X-Ray Fluorescence
|
| ASTM A 792/A 792Ma-2006
| 經熱浸工藝涂層55%鋁鋅合金鐵薄板材標準規范
| Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
|
| ASTM A 882/A 882Ma-2004
| 填充式環氧樹脂涂層的7股預應力鋼絞線標準規范
| Standard Specification for Filled Epoxy-Coated Seven-Wire Prestressing Steel Strand
|
| ASTM A 899-1991
| 環氧涂層鋼絲
| Steel Wire, Epoxy-Coated
|
| ASTM A 90/A 90M-2007
| 帶鋅或鋅合金涂層的鋼鐵制品上涂層重量(質量)用標準試驗方法
| Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
|
| ASTM A 924/A 924M-2007
| 熱浸金屬涂層鋼薄板一般要求的標準規范
| Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process
|
| ASTM A 926-2003
| 波紋形金屬管用涂層材料耐磨性比較的標準試驗方法
| Standard Test Method for Comparing the Abrasion Resistance of Coating Materials for Corrugated Metal Pipe
|
| ASTM A 933/A 933M-2007
| 加固用聚氯乙烯(PVC)涂層鋼絲和焊接鋼絲網的標準規范
| Standard Specification for Vinyl (PVC) Coated Steel Wire and Welded Wire Fabric for Reinforcement
|
| ASTM A 950/A 950M-1999
| 熔接環氧樹脂涂層結構鋼氫反應堆和垛板的標準規范
| Standard Specification for Fusion-Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling
|
| ASTM A 974-1997
| 焊線纖維金屬筐和金屬絲網的標準規范.(金屬涂層或聚氯乙烯(PVC)涂層)
| Standard Specification for Welded Wire Fabric Gabions and Gabion Mattresses (Metallic Coated or Polyvinyl Chloride (PVC) Coated)
|
| ASTM A 975-1997
| 雙層和扭轉網眼金屬筐和護墻墊金屬和涂層鋼線或聚氯乙烯(PVC)金屬涂層鋼線
| Standard Specification for Double-Twisted Hexagonal Mesh Gabions and Revet Mattresses (Metallic-Coated Steel Wire or Metallic-Coated Steel Wire With Poly(Vinyl Chloride) (PVC) Coating)
|
| ASTM A 976-2003
| 與絕緣能力和應用相關的復合絕緣涂層的標準分類
| Standard Classification of Insulating Coatings by Composition, Relative Insulating Ability and Application
|
| ASTM B 252-1992
| 電鍍層和轉化涂層用鋅合金壓模鑄件的制備
| Preparation of Zinc Alloy Die Castings for Electroplating and Conversion Coatings
|
| ASTM B 588-1988
| 用雙束干涉顯微技術測量透明涂層或不透明涂層厚度的試驗方法
| Test Method for Measurement of Thickness of Transparent or Opaque Coatings by Double-Beam-Interference Microscope Technique
|
| ASTM B 602-1988
| 金屬及無機涂層的屬性抽樣試驗方法
| Test Method for Attribute Sampling of Metallic and Inorganic Coatings
|
| ASTM B 681-1988
| 用光截面顯微鏡測量鋁陽極鍍層厚度及不透明表面的其它透明涂層厚度的試驗方法
| Test Method for Measurement of Thickness of Anodic Coatings on Aluminum and of Other Transparent Coatings on Opaque Surfaces Using the Light-Section Microscope
|
| ASTM B 733-2004
| 金屬表面自催化(無電)鎳磷涂層標準規范
| Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal
|
| ASTM B 735-2006
| 用硝酸蒸汽測試金屬基體上金涂層孔隙率的標準試驗方法
| Standard Test Method for Porosity in Gold Coatings on Metal Substrates by Nitric Acid Vapor
|
| ASTM B 748-1990
| 用掃描電子顯微鏡測量橫截面測定金屬涂層厚度的方法
| Test Method for Measurement of Thickness of Metallic Coatings by Measurement of Cross Section with a Scanning Electron Microscope
|
| ASTM B 750-2007
| 熱浸涂層用錠鐵模型中GALFAN(鋅-5%鋁-含鈰稀土)合金的標準規范
| Standard Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings
|
| ASTM B 762-1990
| 金屬涂層和無機物涂層的不同抽樣
| Variables Sampling of Metallic and Inorganic Coatings
|
| ASTM B 766-1986
| 鎘電沉積涂層標準規范
| Standard Specification for Electrodeposited Coatings of Cadmium
|
| ASTM B 767-1988
| 用重量分析法和其它化學分析法測定電沉積涂層及相關涂層單位面積的質量
| Determining Mass Per Unit Area of Electrodeposited and Related Coatings by Gravimetric and Other Chemical Analysis Procedures
|
| ASTM B 798-1995
| 用凝膠體電譜法測定金屬基物上金或鈀涂層孔隙度的標準試驗方法
| Standard Test Method for Porosity in Gold or Palladium Coatings on Metal Substrates by Gel-Bulk Electrography
|
| ASTM B 809-1995
| 用濕硫黃蒸氣("硫黃華")作金屬涂層中孔隙率測試的標準試驗方法
| Standard Test Method for Porosity in Metallic Coatings by Humid Sulfur Vapor ("Flowers-of-Sulfur")
|
| ASTM B 866-1995
| 用聚硫化物浸入法測試金屬涂層中總疵點和機械損壞的標準試驗方法
| Standard Test Method for Gross Defects and Mechanical Damage in Metallic Coatings by Polysulfide Immersion
|
| ASTM B 879-1997
| 鎂和鎂合金上非電解質轉換涂層的標準規范
| Standard Practice for Applying Non-Electrolytic Conversion Coatings on Magnesium and Magnesium Alloys
|
| ASTM B 893-1998
| 工程應用硬涂層陽極氧化規范
| Specification for Hard-Coat Anodizing of Magnesium for Engineering Applications
|
| ASTM B 940-2005
| 在鋅和鎘表面非鉻酸涂層試驗的標準實施規程
| Standard Practice for Testing Non-Chromate Coatings on Zinc and Cadmium Surfaces
|
| ASTM C 1048-2004
| 熱處理平板玻璃的標準規范.HS和FT類涂層和無涂層玻璃
| Standard Specification for Heat-Treated Flat Glass - Kind HS, Kind FT Coated and Uncoated Glass
|
| ASTM C 1321-2004
| 建筑物內部輻射控制涂層系統(IRCCS)的安裝和使用的標準實施規程
| Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction
|
| ASTM C 1483-2004
| 建筑物外部防太陽輻射涂層的標準規范
| Standard Specification for Exterior Solar Radiation Control Coatings on Buildings
|
| ASTM C 1624-2005
| 用定量單點劃痕試驗測定陶瓷涂層粘結強度和機械損壞類型的標準試驗方法
| Standard Test Method for Adhesion Strength and Mechanical Failure Modes of Ceramic Coatings by Quantitative Single Point Scratch Testing
|
| ASTM C 216a-2007
| 涂層磚(由粘土或頁巖制造的實心砌塊)的標準規范
| Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
|
| ASTM C 419-1994
| 膠泥絕熱涂層的試樣制作與養護的標準實施指南
| Standard Practice for Making and Curing Test Specimens of Mastic Thermal Insulation Coatings
|
| ASTM C 536-1983
| 鋼制設備玻璃涂層的連續性電測試的標準試驗方法
| Standard Test Method for Continuity of Coatings in Glassed Steel Equipment by Electrical Testing
|
| ASTM C 537-1987
| 用高壓法測試鋼制反應設備玻璃涂層可靠性的標準試驗方法
| Standard Test Method for Reliability of Glass Coatings on Glassed Steel Reaction Equipment by High Voltage
|
| ASTM C 633-2001
| 熱噴涂層的粘附力或粘結強度的標準試驗方法
| Standard Test Method for Adhesion or Cohesion Strength of Thermal Spray Coatings
|
| ASTM C 703-1972
| 鋁制搪瓷涂層的抗脫落試驗方法
| Test Methods for Spalling Resistance of Porcelain Enameled Aluminum
|
| ASTM C 743-1987
| 搪瓷涂層連續性的標準試驗方法
| Standard Test Method for Continuity of Porcelain Enamel Coatings
|
| ASTM C 884/C 884M-1998
| 混凝土和環氧樹脂涂層間熱容性的標準試驗方法
| Standard Test Method for Thermal Compatibility Between Concrete and an Epoxy-Resin Overlay
|
| ASTM D 1005-1995
| 用千分尺測量有機涂層干膜厚度的標準試驗方法
| Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
|
| ASTM D 1014-2002
| 金屬基質涂料和涂層的室外暴露的標準試驗規程
| Standard Practice for Conducting Exterior Exposure Tests of Paints and Coatings on Metal Substrates
|
| ASTM D 1053a-1992
| 橡膠性能的標準試驗方法.低溫下固化:撓性聚合物和涂層織物
| Standard Test Methods for Rubber Property-Stiffening at Low Temperatures: Flexible Polymers and Coated Fabrics
|
| ASTM D 1187-1997
| 金屬保護涂層用瀝清乳液的標準規范
| Standard Specification for Asphalt-Base Emulsions for Use as Protective Coatings for Metal
|
| ASTM D 1188-2007
| 使用涂層樣品的壓實瀝青混合料的毛體積比重和密度的標準試驗方法
| Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Coated Samples
|
| ASTM D 1212-1991
| 有機涂層濕膜厚度的測試方法
| Test Methods for Measurement of Wet Film Thickness of Organic Coatings
|
| ASTM D 1227-1995
| 屋面保護涂層用乳化瀝青的標準規范
| Standard Specification for Emulsified Asphalt Used as a Protective Coating for Roofing
|
| ASTM D 1458-2001
| 電絕緣用完全硫化硅橡膠涂層的玻璃布與玻璃帶的標準試驗方法
| Standard Test Methods for Fully Cured Silicone Rubber-Coated Glass Fabric and Tapes for Electrical Insulation
|
| ASTM D 1459-1993
| 電絕緣用硅清漆涂層的玻璃布和玻璃帶的標準規范
| Standard Specification for Silicone Varnished Glass Cloth and Tape for Electrical Insulation
|
| ASTM D 1474-1998
| 有機涂層壓痕硬度的試驗方法
| Test Methods for Indentation Hardness of Organic Coatings
|
| ASTM D 16-2007
| 涂料、相關涂層、材料和應用的標準術語
| Standard Terminology for Paint, Related Coatings, Materials, and Applications
|
| ASTM D 1653-2003
| 有機涂層薄膜水蒸氣滲透性標準試驗方法
| Standard Test Methods for Water Vapor Transmission of Organic Coating Films
|
| ASTM D 1735-2004
| 用水霧儀進行涂層耐水性試驗的標準規程
| Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
|
| ASTM D 1931-1999
| 電絕緣用完全硫化的硅橡膠涂層玻璃布和玻璃帶的標準規范
| Standard Specification for Fully Cured Silicone Rubber-Coated Glass Fabric and Tapes for Electrical Insulation
|
| ASTM D 2136-2002
| 涂層織物的低溫彎曲標準試驗方法
| Standard Test Method for Coated Fabrics-Low-Temperature Bend Test
|
| ASTM D 2137-2005
| 橡膠特性的標準試驗方法.撓性聚合物和涂層織物的脆化點
| Standard Test Methods for Rubber Property-Brittleness Point of Flexible Polymers and Coated Fabrics
|
| ASTM D 2197-1998
| 用刮板式粘合試驗器測定有機涂層粘合性的試驗方法
| Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion
|
| ASTM D 2247-2002
| 涂層在100%相對濕度下耐水性的試驗的標準操作規程
| Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity
|
| ASTM D 2248a-2001
| 有機涂層的耐洗滌劑性能的標準規范
| Standard Practice for Detergent Resistance of Organic Finishes
|
| ASTM D 2336-1999
| 涂料廠對涂覆于木制品的涂層由液態至固態的標準指南
| Standard Guide for Specifying Factory Applied Wood Coatings
|
| ASTM D 2370-1998
| 有機涂層抗拉性能試驗方法
| Standard Test Method for Tensile Properties of Organic Coatings
|
| ASTM D 2454-1995
| 測定烘焙過度對有機涂層的影響的標準操作規程
| Standard Practice for Determining the Effect of Overbaking on Organic Coatings
|
| ASTM D 268-2001
| 涂料及其相關涂層和原料用揮發性溶劑及化學中間體的抽樣和測試的標準指南
| Standard Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and Material
|
| ASTM D 2697-2003
| 透明或著色涂層中不揮發物體積的標準測試方法
| Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings
|
| ASTM D 2793-1999
| 木板制底材上有機涂層抗粘連性的標準試驗方法
| Standard Test Method for Block Resistance of Organic Coatings on Wood Panel Substrates
|
| ASTM D 2794-1993
| 有機涂層抗快速形變(沖擊)作用的標準試驗方法
| Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
|
| ASTM D 2803-2003
| 金屬有機涂層耐絲狀銹蝕的試驗用標準指南
| Standard Guide for Testing Filiform Corrosion Resistance of Organic Coatings on Metal
|
| ASTM D 2824-2006
| 無纖維增強、石棉纖維增強和無石棉的纖維增強的填充鋁顏料的瀝青屋面涂層標準規范
| Standard Specification for Aluminum-Pigmented Asphalt Roof Coatings, Nonfibered, Asbestos Fibered, and Fibered without Asbestos
|
| ASTM D 2967-2007
| 粉末涂層角落敷層的標準試驗方法
| Standard Test Method for Corner Coverage of Powder Coatings
|
| ASTM D 3003-2001
| 金屬襯底表面有機涂層耐壓力斑跡和抗粘連性標準試驗方法
| Standard Test Method for Pressure Mottling and Blocking Resistance of Organic Coatings on Metal Substrates
|
| ASTM D 3236-1988
| 熱熔粘合劑及涂層材料表觀粘度的標準試驗方法
| Standard Test Method for Apparent Viscosity of Hot Melt Adhesives and Coating Materials
|
| ASTM D 3259-1995
| 紅外線測定木制品涂層固化期間溫度的標準實施規程
| Standard Practice for Infrared Determination of the Temperature of Applied Coatings on Wood Products During the Curing Cycle
|
| ASTM D 3260-2001
| 適用于工廠的壓制鋁制品透明涂層的耐酸和耐灰漿標準試驗方法
| Standard Test Method for Acid and Mortar Resistance of Factory-Applied Clear Coatings on Extruded Aluminum Products
|
| ASTM D 3273-2000
| 環境模擬室內涂層表面的抗霉菌生長標準試驗方法
| Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber
|
| ASTM D 3281-1984
| 用沖擊邊緣彎曲儀測定附加有機涂層可成形性的試驗方法
| Test Method for Formability of Attached Organic Coatings with Impact-Wedge Bend Apparatus
|
| ASTM D 3361-2001
| 用非濾光碳弧型裝置測定涂料和有關涂層的標準實施規程
| Standard Practice for Unfiltered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings
|
| ASTM D 3389-2005
| 涂層織物耐磨性的標準試驗方法(旋轉平臺雙頭磨蝕機)
| Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform, Double-Head Abrader)
|
| ASTM D 3393-1991
| 涂層織物.耐水性
| Coated Fabrics - Waterproofness
|
| ASTM D 3450-2000
| 內用建筑涂層可洗性的標準試驗方法
| Standard Test Method for Washability Properties of Interior Architectural Coatings
|
| ASTM D 3451-2006
| 試驗涂層粉末和粉末涂層的標準指南
| Standard Guide for Testing Coating Powders and Powder Coatings
|
| ASTM D 3625-1996
| 用開水測試水對瀝青涂層集料的影響的標準操作規程
| Standard Practice for Effect of Water on Bituminous-Coated Aggregate Using Boiling Water
|
| ASTM D 3630-1989
| 測定保護涂層中有害成分的方法
| Determining Constituents Classified as Hazardous Contained in Protective Coatings
|
| ASTM D 3792-2005
| 直接注入式氣相色譜法測定涂層中水含量的標準試驗方法
| Standard Test Method for Water Content of Coatings by Direct Injection Into a Gas Chromatograph
|
| ASTM D 3843-2000
| 核裝置防護涂層質量保證的標準實施規程
| Standard Practice for Quality Assurance for Protective Coatings Applied to Nuclear Facilities
|
| ASTM D 3911-2003
| 設計基本事故(DBA)的模擬條件下評價輕水核電站用涂層的標準試驗方法
| Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions
|
| ASTM D 3912-1995
| 輕水核電站用涂層耐化學性的標準試驗方法
| Standard Test Method for Chemical Resistance of Coatings Used in Light-Water Nuclear Power Plants
|
| ASTM D 3925-2002
| 液態涂料和相關顏料涂層的抽樣標準實施規程
| Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings
|
| ASTM D 3949-1999
| 電絕緣用玻璃涂層織物的標準規范
| Standard Specification for Coated Glass Fabrics Used for Electrical Insulation
|
| ASTM D 3960-2005
| 涂料及相關涂層中揮發性有機化合物含量測定的標準實施規范
| Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
|
| ASTM D 3964-2004
| 表面測量用涂層試樣的選擇的標準規程
| Standard Practice for Selection of Coating Specimens for Appearance Measurements
|
| ASTM D 4005-1992
| 塑料涂覆織物.聚氯乙烯彌散涂層的溶解度的試驗方法
| Standard Test Method for Plastic-Coated Fabrics - Completeness of Fusion of PVC Dispersion Coatings
|
| ASTM D 4060-2007
| 用泰伯爾磨蝕機測定有機涂層耐磨性的標準試驗方法
| Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
|
| ASTM D 4061-1994
| 平面涂層回復反射的標準試驗方法
| Standard Test Method for Retroreflectance of Horizontal Coatings
|
| ASTM D 4082-1995
| Υ射線對輕水核電站用涂層影響的標準試驗方法
| Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants
|
| ASTM D 4109a-1995
| 男人及男孩用機織連衣褲工作服、勞動布工作服、工裝褲及車間涂層織物的標準性能規范
| Standard Performance Specification for Mens and Boys Woven Coverall, Dungaree, Overall, and Shop-Coat Fabrics
|
| ASTM D 4118-2001
| 婦女用機織工作服、勞動布、工裝褲及車間涂層織物的標準性能規范
| Standard Performance Specification for Women's Woven Coverall, Dungaree, Overall, and Shop Coat Fabrics
|
| ASTM D 4138a-2007
| 用橫截面分割破壞法測定防護涂層系統干膜厚度的標準實施規程
| Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means
|
| ASTM D 4141-2007
| 涂層的黑箱和陽光集中暴露處理用標準實施規程
| Standard Practice for Conducting Black Box and Solar Concentrating Exposures of Coatings
|
| ASTM D 4144-1994
| 紫外線固化涂層包裝耐久性評估的標準試驗方法
| Standard Test Method for Estimating Package Stability of Coatings for Ultraviolet Curing
|
| ASTM D 4145-1983
| 預涂板涂層柔韌性試驗方法
| Test Method for Coating Flexibility of Prepainted Sheet
|
| ASTM D 4146-1996
| 鋼材表面富鋅底漆/鉻酸鹽復合涂層可成形性的標準試驗方法
| Standard Test Method for Formability of Zinc-Rich Primer/Chromate Complex Coatings on Steel
|
| ASTM D 4147-1999
| 線繞收縮用線圈涂層的適用規程
| Applying Coil Coatings Using the Wire-Wound Drawdown Bar
|
| ASTM D 4227-2005
| 混凝土表面涂層涂刷油漆工的資格評定的標準實施規程
| Standard Practice for Qualification of Coating Applicators for Application of Coatings to Concrete Surfaces
|
| ASTM D 4228-2005
| 鋼表面涂層涂刷油漆工的資格評定的標準實施規程
| Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces
|
| ASTM D 4457-2002
| 直接注入氣相色譜儀法測定涂料及涂層中二氯甲烷和1,1,1-三氯乙烷的標準試驗方法
| Standard Test Method for Determination of Dichloromethane and 1,1,1-Trichloroethane in Paints and Coatings by Direct Injection into a Gas Chromatograph
|
| ASTM D 4479-2007
| 無石棉的瀝表屋面涂層用標準規范
| Standard Specification for Asphalt Roof Coatings - Asbestos-Free
|
| ASTM D 4537a-2004
| 核設施涂層工作檢驗人員的資格和認證考核程序確立的標準指南
| Standard Guide for Establishing Procedures to Qualify and Certify Personnel Performing Coating Work Inspection in Nuclear Facilities
|
| ASTM D 4541-2002
| 用手提式粘合試驗儀測定涂層脫落強度的標準試驗方法
| Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
|
| ASTM D 4585-2007
| 用受控冷凝法測試涂層耐水性的標準實施規程
| Standard Practice for Testing Water Resistance of Coatings Using Controlled Condensation
|
| ASTM D 4587-2005
| 涂料及相關涂層的熒光紫外線聚合曝光的標準實施規程
| Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings
|
| ASTM D 4610-1998
| 測定涂料和相關涂層上微生物(真菌或藻類)的存在及清除的標準指南
| Standard Guide for Determining the Presence of and Removing Microbial (Fungal or Algal) Growth on Paint and Related Coatings
|
| ASTM D 4712a-1987
| 檢驗工業用水的標準指南.可還原涂層
| Standard Guide for Testing Industrial Water-Reducible Coatings
|
| ASTM D 4851-2007
| 建筑用涂層織物和層疊織物的標準試驗方法
| Standard Test Methods for Coated and Laminated Fabrics for Architectural Use
|
| ASTM D 4917-1997
| 用水平面法測試無涂層書寫紙和印刷紙的靜磨擦和動磨擦系數的標準試驗方法
| Standard Test Method for Coefficient of Static and Kinetic Friction of Uncoated Writing and Printing Paper by Use of the Horizontal Plane Method
|
| ASTM D 4918-1997
| 用傾斜面法測試無涂層書寫紙和印刷紙靜磨擦系數的標準試驗方法
| Standard Test Method for Coefficient of Static Friction of Uncoated Writing and Printing Paper by Use of the Inclined Plane Method
|
| ASTM D 4939-1989
| 在天然海水中使船只防污涂層遭受生物污垢和流體剪切力的試驗方法
| Test Method for Subjecting Marine Antifouling Coating to Biofouling and Fluid Shear Forces in Natural Seawater
|
| ASTM D 5009-2002
| 實驗室條件下評估和比較噴涂層傳送效率的標準試驗方法
| Standard Test Method for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under Laboratory Conditions
|
| ASTM D 5031-2001
| 使用封閉碳弧光燈曝露儀對涂料及有關涂層進行試驗的標準實施規程
| Standard Practice for Enclosed Carbon-Arc Exposure Tests of Paint and Related Coatings
|
| ASTM D 5043-2004
| 涂層現場識別的標準規程
| Standard Practice for Field Identification of Coatings
|
| ASTM D 5065-2007
| 鋼表面老化涂層條件的評估用標準指南
| Standard Guide for Assessing the Condition of Aged Coatings on Steel Surfaces
|
| ASTM D 5087-2002
| 測定含溶劑汽車涂層釋放的和在揮發有機化合物控制裝置中可除去的揮發有機化合物總量的標準試驗方法
| Standard Test Method for Determining Amount of Volatile Organic Compound (VOC) Released from Solventborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement)
|
| ASTM D 5108-1990
| 海水中防污涂層體系有機物擴散速度的測試方法
| Test Method for Organotin Release Rates of Antifouling Coating Systems in Sea Water
|
| ASTM D 5139-1990
| 核電廠用涂層定量檢查用的樣品制備標準規范
| Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants
|
| ASTM D 5161a-2004
| 確定涂層和鑲襯作業(金屬襯里)檢驗要求的標準指南
| Standard Guide for Specifying Inspection Requirements for Coating and Lining Work (Metal Substrates)
|
| ASTM D 5163a-2005
| 核電廠運行時使用的I級涂層性能監測程序制定的標準指南
| Standard Guide for Establishing Procedures to Monitor the Performance of Service Level I Coatings in an Operating Nuclear Power Plant
|
| ASTM D 5179-2002
| 直接抗拉試驗測定有機涂層和塑料基質的粘著力的標準試驗方法
| Standard Test Method for Measuring Adhesion of Organic Coatings to Plastic Substrates by Direct Tensile Testing
|
| ASTM D 5193/D 5193M-1993
| 涂層織物的試驗方法.空氣保持性
| Test Method for Coated Fabrics - Air Retention
|
| ASTM D 522a-1993
| 涂覆有機涂層的芯桿彎曲試驗的標準試驗方法
| Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings
|
| ASTM D 5382-2002
| 粉末涂層光學特性評定標準指南
| Standard Guide to Evaluation of Optical Properties of Powder Coatings
|
| ASTM D 5479-1994
| 部分浸入的船舶涂層的耐生物污垢試驗的標準規程
| Standard Practice for Testing Biofouling Resistance of Marine Coatings Partially Immersed
|
| ASTM D 5531-2005
| 涂層的顏色和幾何外觀的實物產品標準的制定、維護和發布的標準指南
| Standard Guide for Preparation, Maintenance, and Distribution of Physical Product Standards for Color and Geometric Appearance of Coatings
|
| ASTM D 5589-1997
| 測定漆膜及有關涂層耐海藻損壞的標準試驗方法
| Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Algal Defacement
|
| ASTM D 5590-2000
| 用加速的四周瓊脂平面培養分析測定漆膜及有關涂層耐霉菌損壞的標準試驗方法
| Standard Test Method for Determining the Resistance of Paint Films and Related Coatings to Fungal Defacement by Accelerated Four-Week Agar Plate Assay
|
| ASTM D 5711-2003
| 粗集料上粘附涂層測定的標準試驗方法
| Standard Test Method for Determining the Adherent Coating on Coarse Aggregates
|
| ASTM D 5767-1995
| 涂層表面成像清晰度光澤儀器測量的標準試驗方法
| Standard Test Methods for Instrumental Measurement of Distinctness-of-Image Gloss of Coating Surfaces
|
| ASTM D 5895-2003
| 用機械式記錄器評定有機涂層在薄膜成形期間干燥或固化的標準試驗方法
| Standard Test Methods for Evaluating Drying or Curing During Film Formation of Organic Coatings Using Mechanical Recorders
|
| ASTM D 5962-1996
| 評定核反應堆的 I 級區域內連續不合格涂層(油漆)標準指南
| Standard Guide for Maintaining Unqualified Coatings (Paints) Within Level I Areas of a Nuclear Power Facility
|
| ASTM D 5965-2002
| 涂層粉末比重的標準測試方法
| Standard Test Methods for Specific Gravity of Coating Powders
|
| ASTM D 6037-1996
| 強光澤涂層耐干磨損的標準試驗方法
| Standard Test Methods for Dry Abrasion Mar Resistance of High Gloss Coatings
|
| ASTM D 609-2000
| 涂料、清漆、轉化涂層和相關覆層產品的測試用冷軋鋼板制備的標準實施規范
| Standard Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products
|
| ASTM D 6132-2004
| 用超聲波儀表對外施的有機涂層的干膜厚度進行無損測量的標準試驗方法
| Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Gage
|
| ASTM D 6133-2002
| 通過直接注入一氣體色譜儀測定含溶劑和含水涂料、涂層、樹脂和原材料中丙酮及甲基和丁基醋酸鹽含量的標準試
| Standard Test Method for Acetone, p-Chlorobenzotrifluoride, Methyl Acetate or t-Butyl Acetate Content of Solventborne and Waterborne Paints, Coatings, Resins, and Raw Materials by Direct Injection Into a Gas Chromatograph
|
| ASTM D 6189-1997
| 有機涂層的化學去除劑的效果評價的標準操作規程
| Standard Practice for Evaluating the Efficiency of Chemical Removers for Organic Coatings
|
| ASTM D 6190-1997
| 通過土壤埋葬的試驗室模仿對管道涂層的陰極非結合的標準試驗方法
| Standard Test Method for Cathodic Disbonding of Pipeline Coatings by Laboratory Simulation of Soil Burial
|
| ASTM D 6191-1997
| 由可水減的空氣干燥涂層離析的甲醛的測量的標準試驗方法
| Standard Test Method for Measurement of Evolved Formaldehyde from Water Reducible Air-Dry Coatings
|
| ASTM D 6266a-2000
| 由VOC控制裝置內除去的涂層和水載汽車涂層中釋放的揮發性有機物(VOC)的總量測定的試驗方法
| Test Method for Determining the Amount of Volatile Organic Compound (VOC) Released From Waterborne Automotive Coatings and Available for Removal in a VOC Control Device (Abatement)
|
| ASTM D 6356-1998
| 用作屋頂防護涂層的鋁乳化瀝青的氫氣體產生的標準試驗方法
| Standard Test Method for Hydrogen Gas Generation of Aluminum Emulsified Asphalt Used as a Protective Coating for Roofing
|
| ASTM D 6441-2005
| 測量粉末涂層遮蓋能力的標準試驗方法
| Standard Test Methods for Measuring the Hiding Power of Powder Coatings
|
| ASTM D 6486-2001
| 汽車涂層的短時暴露的標準實施規程
| Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings
|
| ASTM D 6580-2000
| 鋅粉涂料與鋅粉涂料硫化薄膜和富鋅涂層硫化薄膜中金屬鋅含量測定的標準試驗方法
| Standard Test Method for the Determination of Metallic Zinc Content in Both Zinc Dust Pigment and in Cured Films of Zinc-Rich Coatings
|
| ASTM D 6675-2001
| 機動車薄鋼板上有機涂層的鹽加速戶外表面腐蝕試驗的標準實施規程
| Standard Practice for Salt-Accelerated Outdoor Cosmetic Corrosion Testing of Organic Coatings on Automotive Sheet Steel
|
| ASTM D 6694-2007
| 噴射聚氨酯泡沫屋頂材料用液體硅涂層的標準規范
| Standard Specification for Liquid-Applied Silicone Coating Used in Spray Polyurethane Foam Roofing
|
| ASTM D 6762a-2002
| 通過噴涂層的外觀評價測定涂料遮蓋能力的標準試驗方法
| Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings
|
| ASTM D 6902-2004
| 蜜胺-甲醛基涂層在固化過程中實驗室測量甲醛含量的標準試驗方法
| Standard Test Method for Laboratory Measurement of Formaldehyde Evolved During the Curing of Melamine-Formaldehyde-Based Coatings
|
| ASTM D 6903-2007
| 從防污涂層測定替代海洋水中有機生物殺菌劑投放率的標準試驗方法
| Standard Test Method for Determination of Organic Biocide Release Rate From Antifouling Coatings in Substitute Ocean Water
|
| ASTM D 6904-2003
| 砌筑體外涂層耐風雨的標準實用規程
| Standard Practice for Resistance to Wind-Driven Rain for Exterior Coatings Applied on Masonry
|
| ASTM D 6905-2003
| 有機涂層沖擊彎曲性的標準試驗方法
| Standard Test Method for Impact Flexibility of Organic Coatings
|
| ASTM D 6943-2003
| 工業防護涂層的浸沒試驗標準規程
| Standard Practice for Immersion Testing of Industrial Protective Coatings
|
| ASTM D 6944-2003
| 硫化涂層耐熱循環的標準試驗方法
| Standard Test Method for Resistance of Cured Coatings to Thermal Cycling
|
| ASTM D 6947-2007
| 噴涂聚氨酯泡沫屋頂系統用液體水分固化聚氨酯涂層的標準規范
| Standard Specification for Liquid Applied Moisture Cured Polyurethane Coating Used in Spray Polyurethane Foam Roofing System
|
| ASTM D 6958-2003
| 木材涂層側粘結潛力評價的標準試驗方法
| Standard Test Methods for Evaluating Side-Bonding Potential of Wood Coatings
|
| ASTM D 6991-2005
| 用懸臂梁法測量有機涂層內部應力的標準試驗方法
| Standard Test Method for Measurements of Internal Stresses in Organic Coatings by Cantilever (Beam) Method
|
| ASTM D 6998-2004
| 評價乳化瀝青集料涂層的標準實施規程
| Standard Practice for Evaluating Aggregate Coating using Emulsified Asphalts
|
| ASTM D 7055-2004
| 涂層試驗用熱軋?zhí)间摫“鍦蕚?噴砂清理)的標準規程
| Standard Practice for Preparation (by Abrasive Blast Cleaning) of Hot-Rolled Carbon Steel Panels for Testing of Coatings
|
| ASTM D 7072-2004
| 評價膠乳涂層加速風化的標準實施規程
| Standard Practice for Evaluating Accelerated Efflorescence of Latex Coatings
|
| ASTM D 7088-2004
| 磚石工程用地下設施涂層的抗流體靜壓力的標準規程
| Standard Practice for Resistance to Hydrostatic Pressure for Coatings Used in Below Grade Applications Applied to Masonry
|
| ASTM D 7091-2005
| 應用于黑色金屬的無磁涂層和應用于有色金屬的無磁和不導電涂層的干膜厚度的無損測量的標準實施規程
| Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals
|
| ASTM D 7093-2004
| 雙軸拉伸穹面上鋼的有機涂層薄膜的可成形性的標準試驗方法
| Standard Test Method for Formability of Thin Film Organic Coatings on Steel Over a Biaxially Stretched Dome
|
| ASTM D 7108-2005
| 確立核涂層專家資格的標準指南
| Standard Guide for Establishing Qualifications for a Nuclear Coatings Specialist
|
| ASTM D 7207-2005
| 利用臺式標稱液力感應剪應力測定無涂層軋制防沖刷制品(RECP)對沙保護能力的標準試驗方法
| Standard Test Method for Determination of Unvegetated Rolled Erosion Control Product (RECP) Ability to Protect Sand from Hydraulically-Induced Shear Stresses under Bench-Scale Conditions
|
| ASTM D 7230-2006
| 評估涂層設施安全等級III的水浸漬的聚合體內管的標準試驗方法. 金屬襯底上相關設備
| Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
|
| ASTM D 7245-2007
| 測定含水總量和加熱產生固化水的液體涂層中揮發物含量的標準試驗方法
| Standard Test Method for Measuring Total Water and Volatiles in Liquid Coatings Which Produce Cure Water Upon Heating
|
| ASTM D 7356-2007
| 用氙弧光曝光裝置加速汽車透明涂層酸侵蝕的標準試驗方法
| Standard Test Method for Accelerated Acid Etch Weathering of Automotive Clearcoats Using a Xenon-Arc Exposure Device
|
| ASTM D 7376-2007
| 卷狀涂層金屬濕豎管存儲條件戶外評定的標準實施規程
| Standard Practice for Outdoor Evaluation of Wet Stack Storage Conditions on Coil-Coated Metals
|
| ASTM D 7378-2007
| 測量實用涂層粉末預固化厚度的標準實施規程
| Standard Practice for Measurement of Thickness of Applied Coating Powders to Predict Cured Thickness
|
| ASTM D 751-2006
| 涂層織物的標準試驗方法
| Standard Test Methods for Coated Fabrics
|
| ASTM D 822-2001
| 用經過過濾的明光碳弧曝光裝置測定涂料及相關涂層的標準實施規程
| Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings
|
| ASTM D 870-2002
| 水浸漬法測試涂層的耐水性能的標準實施規程
| Standard Practice for Testing Water Resistance of Coatings Using Water Immersion
|
| ASTM E 1317a-1997
| 船舶表面涂層易燃性的標準試驗方法
| Standard Test Method for Flammability of Marine Surface Finishes
|
| ASTM E 1522-1993
| 實驗室玻璃器皿耐高壓加熱保護涂層
| Autoclavable Protective Coatings on Laboratory Glassware
|
| ASTM E 1659-2005
| 電鍍鎳鋅合金薄鋼板的涂層重量和化學分析的標準試驗方法
| Standard Test Methods Coating Weight and Chemical Analysis of Zinc-Nickel Alloy Electrolytically Coated on Steel Sheet
|
| ASTM E 1795-2004
| 建筑物含鉛漆用非增強液體涂層封裝產品標準規范
| Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
|
| ASTM E 1796-2003
| 建筑物中含鉛漆的液體涂層封裝產品的選擇和使用的標準指南
| Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings
|
| ASTM E 1797-2004
| 建筑物中含鉛漆用增強的液體涂層封裝產品用標準規范
| Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
|
| ASTM E 1814-1996
| 涂層的計算機層析攝影(CT)檢查的標準實施規范
| Standard Practice for Computed Tomographic (CT) Examination of Castings
|
| ASTM E 1920-2003
| 熱噴涂層的金相制備用標準指南
| Standard Guide for Metallographic Preparation of Thermal Sprayed Coatings
|
| ASTM E 2098-2000
| PB級外絕緣和涂層系統(EIFS)中使用的玻璃纖維增強網暴露于氫氧化鈉溶液后拉伸斷裂強度測定的標準試驗方法
| Standard Test Method for Determining Tensile Breaking Strength of Glass Fiber Reinforcing Mesh for Use in Class PB Exterior Insulation and Finish Systems (EIFS), after Exposure to a Sodium Hydroxide Solution
|
| ASTM E 2109-2000
| 測定熱噴鍍涂層孔隙率面積百分比的試驗方法
| Test Methods for Determining Area Percentage Porosity in Thermal Sprayed Coatings
|
| ASTM E 2134-2001
| 評定外部絕緣和涂層系統拉伸-粘著特性的標準試驗方法
| Standard Test Method for Evaluating the Tensile-Adhesion Performance of an Exterior Insulation and Finish System (EIFS)
|
| ASTM E 2141-2006
| 密封隔熱玻璃元件上吸收的電鍍鉻涂層穩定性評價的標準試驗方法
| Standard Test Methods for Assessing the Durability of Absorptive Electrochromic Coatings on Sealed Insulating Glass Units
|
| ASTM E 2338-2006
| ASTM E 2338-2006Standard Practice for Characterization of Coatings Using Conformable Eddy-Current Se
| Standard Practice for Characterization of Coatings Using Conformable Eddy-Current Sensors without Coating Reference Standards
|
| ASTM E 2354-2004
| 密封絕緣玻璃設備內吸收性電致變色涂層的耐用性評估用標準指南
| Standard Guide for Assessing the Durability of Absorptive Electrochromic Coatings within Sealed Insulating Glass Units
|
| ASTM E 2355-2004
| 拋光表面上吸收性電致變色涂層均勻性測量的標準試驗方法
| Standard Test Method for Measuring the Uniformity of an Absorptive Electrochromic Coating on a Glazing Surface
|
| ASTM E 2485-2006
| 耐冷凍/解凍融化的外部絕緣和裝飾系統(EIFS)和防水涂層的標準術語
| Standard Test Method for Freeze/Thaw Resistance of Exterior Insulation and Finish Systems (EIFS) and Water Resistive Barrier Coatings
|
| ASTM E 2501-2007
| 熒光粉涂層檢驗用光源產品的標準規范
| Standard Specification for Light Source Products for Inspection of Fluorescent Coatings
|
| ASTM E 2570-2007
| 外部絕緣和精整系統或排水管中用防水物障涂層評定的標準試驗方法
| Standard Test Methods for Evaluating Water-Resistive Barrier (WRB) Coatings Used under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage
|
| ASTM F 1043-2006
| 金屬工業鏈護欄框架強度和保護性涂層的標準規范
| Standard Specification for Strength and Protective Coatings on Steel Industrial Chain Link Fence Framework
|
| ASTM F 1136M-2004
| 緊固件的抗鋅/鋁腐蝕涂層的標準規范(米制)
| Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners [Metric]
|
| ASTM F 1428-1992
| 緊固件用非有機頂涂層,防腐蝕涂層的鋁顆粒填充底涂層/有機物
| Aluminum Particle-Filled Basecoat/Organic of Inorganic Topcoat, Corrosion Protective Coatings for Fasteners
|
| ASTM F 1609-2003
| 可植入材料用磷酸鈣涂層標準規范
| Standard Specification for Calcium Phosphate Coatings for Implantable Materials
|
| ASTM F 1664-2001
| 與鏈接柵欄一起使用的聚氯乙烯涂層拉伸鋼絲的標準規范
| Standard Specification for Poly(Vinyl Chloride) (PVC)-Coated Steel Tension Wire Used with Chain-Link Fence
|
| ASTM F 1665-2001
| 與鏈接柵欄一起使用的聚氯乙烯涂層刺鋼絲的標準規范
| Standard Specification for Poly(Vinyl Chloride) (PVC)and Other Conforming Organic Polymer-Coated Steel Barbed Wire Used With Chain-Link Fence
|
| ASTM F 1842-2002
| 測定薄膜開關的塑料基質上油墨或涂層粘附的標準試驗方法
| Standard Test Method for Determining Ink or Coating Adhesion on Plastic Substrates for Membrane Switch Applications
|
| ASTM F 1916-1998
| 選擇拘役用帶涂層鏈節柵欄結構和圓柱的鏈節柵欄系統的標準規范
| Standard Specifications for Selecting Chain Link Barrier Systems With Coated Chain Link Fence Fabric and Round Posts for Detention Applications
|
| ASTM F 1978-2000
| 用泰伯磨耗試驗機測定金屬化熱噴射涂層抗磨損性的標準試驗方法
| Standard Test Method for Measuring Abrasion Resistance of Metallic Thermal Spray Coatings by Using the Taber Abraser
|
| ASTM F 2016-2000
| 確定造船船體構造、裝配和涂層質量要求的標準實施規范
| Standard Practice for Establishing Shipbuilding Quality Requirements for Hull Structure, Outfitting, and Coatings
|
| ASTM F 2217-2002
| 涂層/粘合劑重量測定標準實施規范
| Standard Practice for Coating/Adhesive Weight Determination
|
| ASTM F 2250-2003
| 柔性包裝材料上打印墨水和涂層抗化學腐蝕性評價的標準規程
| Standard Practice for Evaluation of Chemical Resistance of Printed Inks and Coatings on Flexible Packaging Materials
|
| ASTM F 2252-2003
| 使用膠帶評價柔性包裝材料與墨水和涂層間粘性的標準規程
| Standard Practice for Evaluating Ink or Coating Adhesion to Flexible Packaging Materials Using Tape
|
| ASTM F 2357-2004
| 使用NORMAN工具"RCA"磨擦器測定薄膜開關上墨水和涂層抗磨性的標準試驗方法
| Standard Test Method for Determining the Abrasion Resistance of Inks and Coatings on Membrane Switches Using the Norman Tool "RCA" Abrader
|
| ASTM F 479-2006
| 絕緣涂層在使用中維護的標準使用規范
| Standard Specification for In-Service Care of Insulating Blankets
|
| ASTM F 519-2006
| 電鍍/涂層處理和設備環境的機械氫脆化評價的標準試驗方法
| Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments
|
| ASTM F 715-2007
| 溢油控制和儲存用涂層織物的標準試驗方法
| Standard Test Methods for Coated Fabrics Used for Oil Spill Control and Storage
|
| ASTM F 718-2007
| 造船廠和船舶漆及涂層制品/程序數據單的標準
| Standard for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet
|
| ASTM F 735-2006
| 用擺動沙袋法測定透明塑料及涂層抗磨損性的標準試驗方法
| Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method
|
| ASTM G 10-1983
| 管道涂層比可彎性的試驗方法
| Standard Test Method for Specific Bendability of Pipeline Coatings
|
| ASTM G 11-2004
| 室外氣候老化對管道涂層的影響的標準試驗方法
| Standard Test Method for Effects of Outdoor Weathering on Pipeline Coatings
|
| ASTM G 12-2007
| 鋼制管道涂層膜厚度的無損測量用標準試驗方法
| Standard Test Method for Nondestructive Measurement of Film Thickness of Pipeline Coatings on Steel
|
| ASTM G 14-2004
| 管道涂層抗沖擊性的標準試驗方法(落錘試驗)
| Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)
|
| ASTM G 17-2007
| 管道涂層耐滲透性用標準試驗方法(鈍頭棒)
| Standard Test Method for Penetration Resistance of Pipeline Coatings (Blunt Rod)
|
| ASTM G 19-2004
| 直接土埋法測定管道涂層抗剝落特性的標準試驗方法
| Standard Test Method for Disbonding Characteristics of Pipeline Coatings by Direct Soil Burial
|
| ASTM G 20-1988
| 管道涂層抗化學藥物腐蝕性的試驗方法
| Test Method for Chemical Resistance of Pipeline Coatings
|
| ASTM G 55-2007
| 管道涂層修補材料的評估用標準試驗方法
| Standard Test Method for Evaluating Pipeline Coating Patch Materials
|
| ASTM G 6-2007
| 管道涂層抗磨性標準試驗方法
| Standard Test Method for Abrasion Resistance of Pipeline Coatings
|
| ASTM G 62-2007
| 管道涂層假期檢測用標準試驗方法
| Standard Test Methods for Holiday Detection in Pipeline Coatings
|
| ASTM G 70-2007
| 管道涂層環形可彎曲性標準試驗方法(壓實試驗)
| Standard Test Method for Ring Bendability of Pipeline Coatings (Squeeze Test)
|
| ASTM G 8-1996
| 管道涂層陰極剝離的標準試驗方法
| Standard Test Methods for Cathodic Disbonding of Pipeline Coatings
|
| ASTM G 80-2007
| 管道涂層特效陰極剝落的標準試驗方法
| Standard Test Method for Specific Cathodic Disbonding of Pipeline Coatings
|
| ASTM G 9-2007
| 管道涂層滲水性的標準試驗方法
| Standard Test Method for Water Penetration into Pipeline Coatings
|
| ASTM G 95-2007
| 管道涂層的陰極剝離試驗用標準試驗方法(附著電池法)
| Standard Test Method for Cathodic Disbondment Test of Pipeline Coatings (Attached Cell Method)
|
| IEEE 1523-2002
| 室外陶瓷絕緣子用室溫硫化硅酮橡膠涂層的應用、維護和評價
| (Application, maintenance, and evaluation of room temperature vulcanizing (RTV) silicone rubber coatings for outdoor ceramic insulators)
|
| 編號 | 中文名稱 | 英文名稱 |
|---|