| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| EN 1013-2-1998 | 單層頂蓋用透光齒形塑料板 第2部分：玻璃纖維增強的聚脂樹脂薄板的特殊要求和試驗方法 | Light transmitting profiled plastic sheeting for single skin roofing - Part 2: Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP) |
| EN 1094-1-1997 | 絕緣耐火產品 第1部分：陶瓷纖維產品術語 | Insulating refractory products - Part 1: Terminology for ceramic fibre products |
| EN 1094-3-2003 | 絕緣耐火產品 第3部分：陶瓷纖維制造的絕緣產品分類 | Insulating refractory products - Part 3: Classification of insulating products made from ceramic fibres |
| EN 1169-1999 | 預制混凝土制品 玻璃纖維增強水泥廠生產控制的一般規則 | Precast concrete products - General rules for factory production control of glass-fibre reinforced cement |
| EN 1170-1-1997 | 預制混凝土制品 玻璃纖維增強水泥試驗方法 第1部分：“坍塌試驗”法 測量基質堅固度 | Precast concrete products - Test method for glass-fibre reinforced cement - Part 1: Measuring the consistency of the matrix "Slump test" method |
| EN 1170-2-1997 | 預制混凝土制品 玻璃纖維增強水泥試驗方法 第2部分：新玻璃纖維增強水泥中纖維含量的測量 沖刷試驗 | Precast concrete products - Test method for glass-fibre reinforced cement - Part 2: Measuring the fibre content in fresh GRC, "Wash out test" |
| EN 1170-3-1997 | 預制混凝土制品 玻璃纖維增強水泥的試驗方法 第3部分：噴射玻璃纖維增強水泥中纖維含量的測量 | Precast concrete products - Test method for glass-fibre reinforced cement - Part 3: Measuring the fibre content of sprayed GRC |
| EN 1170-4-1997 | 預制混凝土制品 玻璃纖維增強水泥的試驗方法 第4部分：測定抗彎強度 簡化彎曲試驗法 | Precast concrete products - Test method for glass-fibre reinforced cement - Part 4: Measuring bending strength, "Simplified bending test" method |
| EN 1170-5-1997 | 預制混凝土制品 玻璃纖維增強水泥的試驗方法 第5部分：測定抗彎強度 完全彎曲試驗法 | Precast concrete products - Test method for glass-fibre reinforced cement - Part 5: Measuring bending strength, "Complete bending test" method |
| EN 1170-6-1997 | 預制混凝土產品 玻璃纖維增強水泥的試驗方法 第6部分：浸漬法對水吸收的測定和干密度的測定 | Precast concrete products - Test method for glass-fibre reinforced cement - Part 6: Determination of the absorption of water by immersion and determination of the dry density |
| EN 1170-7-1997 | 預制混凝土制品 玻璃纖維增強水泥的試驗方法 第7部分：由于濕度引起尺寸變化的極限的測定 | Precast concrete products - Test method for glass-fibre reinforced cement - Part 7: Measurement of extremes of dimensional variations due to moisture content |
| EN 12132-1-1998 | 羽毛和羽絨 纖維羽絨透氣性能的試驗方法 摩擦試驗 | Feather and down - Methods of testing the down proof properties of fabrics - Part 1: Rubbing test |
| EN 12132-2-1998 | 羽毛和羽絨 纖維羽絨透氣性能的試驗方法 沖擊試驗 | Feather and down - Methods of testing the down proof properties of fabrics - Part 2: Impact test |
| EN 12195-2-2000 | 道路車輛的貨物約束裝置 安全 第2部分：人造纖維捆綁帶 | Load restraint assemblies on road vehicles - Safety - Part 2: Web lashing made from man-made fibres |
| EN 12369-1-2001 | 木基板 結構設計特征值 第1部分： OSB、顆粒板和纖維板 | Wood-based panels - Characteristic values for structural design - Part 1: OSB, particleboards and fibreboards |
| EN 12467-2000+AC-2000 | 纖維膠合平板 產品規格和試驗方法 | Fibre-cement flat sheets - Product specifications and test methods / Note: To be replaced by prEN 12467 (2003-08). |
| EN 12575-1998 | 塑料 熱固模塑物料 SMC中纖維浸濕程度的測定 | Plastics - Thermoset moulding compounds - Determination of the degree of fibre wet out in SMC |
| EN 12576-1998 | 塑料 纖維增強復合物 SMC、BMC和DMC的壓縮模制試驗板的制備 | Plastics - Fibre reinforced composites - Preparation of compression moulded test plates of SMC, BMC and DMC |
| EN 12590-1999 | 紡織品 完全或部分用合成纖維制的工業縫紉線 | Textiles - Industrial sewing threads made wholly or partly from synthetic fibres |
| EN 1261-1995 | 一般用途纖維繩索 大麻繩 | Fibre ropes for general service - Hemp |
| EN 12654-1-1998 | 紡織玻璃纖維 紗 第１部分：名稱 | Textile glass - Yarns - Part 1: Designation |
| EN 12654-2-1998 | 紡織玻璃纖維 紗 第２部分：試驗方法和一般規范 | Textile glass - Yarns - Part 2: Methods of test and general specifications |
| EN 12654-3-1998 | 紡織玻璃纖維 紗 第３部分：一般應用的一般要求 | Textile glass - Yarns - Part 3: General requirements for general applications |
| EN 12710-1999 | 纖維板柱桶 公稱容量為15升至250升的帶封閉環的可移動頭(開口)式桶 | Fibreboard drums - Removable head (open head) drums with closing rings with a nominal capacity of 15 l to 250 l |
| EN 12751-1999 | 紡織品 試驗用纖維、紗和織物的抽樣 | Textiles - Sampling of fibres, yarns and fabrics for testing |
| EN 12763-2000 | 建筑物排水系統的纖維膠合管及附件 交貨尺寸和技術術語 | Fibre-cement pipes and fittings for discharge systems for buildings - Dimensions and technical terms of delivery |
| EN 12971-1-1999 | 加強材料 紡織玻璃纖維碎絲規范 第1部分：名稱 | Reinforcements - Specification for textile glass chopped strands - Part 1: Designation |
| EN 12971-2-1999 | 加強材料 紡織玻璃纖維碎絲規范 第2部分：試驗方法和一般要求 | Reinforcements - Specification for textile glass chopped strands - Part 2: Test methods and general requirements |
| EN 12971-3-1999 | 加強材料 紡織玻璃纖維碎絲規范 第3部分：特殊需求 | Reinforcements - Specification for textile glass chopped strands - Part 3: Specific requirements |
| EN 13002-2-1999 | 碳纖維紗 第2部分：試驗方法和通用規范 | Carbon fibre yarns - Part 2: Test methods and general specifications |
| EN 13003-1-1999 | 聚酰胺纖維絲線 第1部分：名稱 | Para-aramid fibre filament yarns - Part 1: Designation |
| EN 13003-2-1999 | 聚酰胺纖維絲線 第2部分：試驗方法和通用規范 | Para-aramid fibre filament yarns - Part 2: Methods of test and general specifications |
| EN 13003-3-1999 | 聚酰胺纖維絲線 第3部分：技術規范 | Para-aramid fibre filament yarns - Part 3: Technical specifications |
| EN 13171-2001 | 建筑物保溫制品 工廠預制木質纖維（WF）制品 規范 | Thermal insulation products for buildings - Factory made wood fibre (WF) products - Specification |
| EN 13280-2001 | 單件式和預制構件拼裝結構的玻璃纖維加強地上冷水蓄水池規范 | Specification for glass fibre reinforced cisterns of one piece and sectional construction, for the storage, above ground, of cold water |
| EN 13413-2001 | 彈性地板覆蓋物 填充纖維底板上的聚氯乙烯地面覆蓋物 規范 | Resilient floor coverings - Polyvinyl chloride floor coverings on a filled fibrous backing - Specification |
| EN 13496-2002 | 建筑物保溫品 玻璃纖維網機械性能測定 | Thermal insulation products for building applications - Determination of the mechanical properties of glass fibre meshes |
| EN 13558-2003 | 家用沐浴器底盤用沖壓成形擠壓聚丙烯脯纖維板規范 | Specifications for impact modified extruded acrylic sheets for shower trays for domestic purposes |
| EN 14020-1-2002 | 增強物 紡織玻璃纖維纖維粗紗的規格 第1部分：命名 | Reinforcements - Specification for textile glass rovings - Part 1: Designation |
| EN 14020-2-2002 | 增強物 紡織玻璃纖維粗紗的規格 第2部分：檢驗方法和一般要求 | Reinforcements - Specification for textile glass rovings - Part 2: Methods of test and general requirements |
| EN 14020-3-2002 | 增強物 紡織玻璃纖維粗紗的規格 第2部分：特殊要求 | Reinforcements - Specification for textile glass rovings - Part 3: Specific requirements |
| EN 14053-2003 | 包裝 由波紋或?qū)嵭睦w維板制造的包裝材料 型號和結構 | Packaging - Packagings manufactured from corrugated or solid fibreboard - Types and construction |
| EN 14118-1-2003 | 增強 紡織玻璃纖維墊規范（短切原絲薄氈和連續纖維薄氈） 第1部分：名稱 | Reinforcement - Specifications for textile glass mats (chopped strand and continuous filament mats) - Part 1: Designation |
| EN 14118-2-2003 | 增強 紡織玻璃纖維墊規范（短切原絲薄氈和連續纖維薄氈） 第2部分：一般要求和試驗方法 | Reinforcement - Specifications for textile glass mats (chopped strand and continuous filament mats) - Part 2: Methods of test and general requirements |
| EN 14118-3-2003 | 增強 紡織玻璃纖維墊規范（短切原絲薄氈和連續纖維薄氈） 第3部分：特殊要求 | Reinforcement - Specifications for textile glass mats (chopped strand and continuous filament mats) - Part 3: Specific requirements |
| EN 14362-2-2003 | 紡織品 從偶氨著色劑衍化的某些芳族胺的測定方法 第2部分：用萃取纖維法獲得使用某些偶氮著色劑的檢測 | Textiles - Methods for determination of certain aromatic amines derived from azo colorants - Part 2: Detection of the use of certain azo colorants accessible by extracting the fibres |
| EN 1444-2000 | 纖維水泥管道 現場工作實踐和鋪設指南 | Fibre-cement pipelines - Guide for laying and on-site work practices |
| EN 1449-1996 | 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)組件 查檢水泥套管插承接合設計的試驗方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of cemented socket-and-spigot joints |
| EN 1492-1-2000 | 織物吊索 安全性 第1部分：一般用途人造纖維扁平織物吊索 | Textile slings - Safety - Part 1: Flat woven webbing slings, made of man-made fibres, for general purpose use |
| EN 1492-2-2000 | 織物吊索 安全性 第2部分：一般用途人造纖維園吊索 | Textile slings - Safety - Part 2: Roundslings, made of man-made fibres, for general purpose use |
| EN 1636-3-1997 | 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第3部分：管件 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings |
| EN 1636-5-1997 | 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第5部分：針對接頭 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints |
| EN 1636-6-1997 | 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第6部分：安裝實踐 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation |
| EN 1787-2000 | 食物 用ESR法檢測含纖維素經過輻射的食品 | Foodstuffs - Detection of irradiated food containing cellulose by ESR spectroscopy |
| EN 1813-1997 | 鋪地織物 用研磨機器對羊毛纖維完整性的測定 | Textile floor coverings - Determination of wool fibre integrity using an abrasion machine |
| EN 23-1-1978 | 洗滌粉和清潔粉的包裝 纖維板硬紙盒和圓筒的尺寸和體積 | Packages for washing and cleaning powders; dimensions and volumes of cartons and drums from fibre board |
| EN 2329-1993 | 航空航天系列 紡織玻璃纖維預浸漬樹脂 測定單位面積質量的試驗方法 | Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of mass per unita area |
| EN 2330-1993 | 航空航天系列 紡織玻璃纖維預浸漬樹脂 測定揮發物質含量的試驗方法 | Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of the content of volatile matter |
| EN 2331-1993 | 航空航天系列 紡織玻璃纖維預浸漬樹脂 測定單位面積樹脂和纖維含量及纖維質量的試驗方法 | Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of the resin and fibre content and mass of fibre per unit area |
| EN 2332-1993 | 航空航天系列 紡織玻璃纖維預浸漬樹脂 測定樹脂流速的試驗方法 | Aerospace series - Textile glass fibre preimpregnates - Test method for the determination of the resin flow |
| EN 2374-1991 | 航空航天系列 玻璃纖維增強模壓件和夾層復合件 試驗板的制備 | Aerospace series - Glass fibre reinforced mouldings and sandwich composites - Production of test panels |
| EN 2377-1989 | 航空航天系列 玻璃纖維增強塑料 試驗方法 表觀層間剪切強度測定 | Aerospace series - Glass fibre reinforced plastics - Test method - Determination of apparent interlaminar shear strength |
| EN 2378-1995 | 航空航天系列 纖維增強塑料 通過浸漬對吸水率的測定 | Aerospace series - Fibre reinforced plastics - Determination of water absorption by immersion |
| EN 2489-1995 | 航空航天系列 纖維增強塑料 試驗液體影響的測定 | Aerospace series - Fibre reinforced plastics - Determination of the action of test fluids |
| EN 2557-1997 | 航空航天系列 碳纖維預浸漬物 單位面積質量的測定 | Aerospace series - Carbon fibre preimpregnates - Determination of mass per unit area |
| EN 2558-1997 | 航空航天系列 碳纖維預浸漬物 揮發物含量測定 | Aerospace series - Carbon fibre preimpregnates - Determination of the volatile content |
| EN 2559-1997 | 航空航天系列 碳纖維預浸漬物 樹脂成分 樹脂和纖維含量及單位面積纖維質量的測定 | Aerospace series - Carbon fibre preimpregnates - Determination of the resin and fibre content and the mass of fibre per unit area |
| EN 2561-1995 | 航空航天系列 碳纖維增強塑料 單向塑料層壓制品 纖維方向平行抗拉試驗 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Tensile test parallel to the fibre direction |
| EN 2562-1997 | 航空航天系列 碳纖維增強塑料 單向?qū)訅核芰稀∨c纖維方向平行的彎曲試驗 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Flexural test parallel to the fibre direction |
| EN 2563-1997 | 航空航天系列 碳纖維增強塑料 單向?qū)訅喊濉娱g表面剪切強度的測定 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Determination of the apparent interlaminar shear strength |
| EN 2564-1998 | 航空航天系列 碳纖維疊層板材 纖維、樹脂含量和空隙率的測定 | Aerospace series - Carbon fibre laminates - Determination of the fibre, resin and void contents |
| EN 2597-1998 | 航空航天系列 碳纖維增強塑料 單向疊層板材 垂直于纖維方向的拉伸試驗 | Aerospace series - Carbon fibre reinforced plastics - Unidirectional laminates - Tensile test perpendicular to the fibre direction |
| EN 2743-2001 | 航空航天系列 纖維增強塑料 測試材料未老化前調理的標準程序 | Aerospace series - Fibre reinforced plastics - Standard procedures for conditioning prior to testing unaged materials |
| EN 2746-1998 | 航空航天系列 玻璃纖維增強塑料 彎曲試驗 三點彎曲法 | Aerospace series - Glass fibre reinforced plastics - Flexural test - Three point bend method |
| EN 2747-1998 | 航空航天系列 玻璃纖維增強塑料 抗拉試驗 | Aerospace series - Glass fibre reinforced plastics - Tensile test |
| EN 300-1997 | 定向纖維板(OSB) 定義、分類和規范 | Oriented Strand Boards (OSB) - Definitions, classification and specifications |
| EN 302-3-1992 | 承重木結構用膠粘劑 試驗方法 第3部分：通過溫度和濕度循環試驗測定酸性腐蝕對木纖維橫向拉伸強度的影響 | Adhesives for load - Bearing timber structures - Test methods - Part 3: Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength |
| EN 316-1999 | 木纖維板 定義、分類和符號 | Wood fibreboards - Definition, classification and symbols |
| EN 317-1993 | 碎料板和纖維板 在水中浸泡后膨脹厚度的測定 | Particleboards and fibreboards; determination of swelling in thickness after immersion in water |
| EN 319-1993 | 碎料板和纖維板 與板平面垂直的拉伸強度的測定 | Particleboards and fibreboards; determination of tensile strength perpendicular to the plane of the board |
| EN 320-1993 | 纖維板 抗螺釘軸向拔出力的測定 | Fibreboards - Determination of resistance to axial withdrawal of screws |
| EN 382-1-1993 | 纖維板 表面吸收性測定 第1部分：干燥處理纖維板試驗方法 | Fibreboards - Determination of surface absorption - Part 1: Test method for dry process fibreboards |
| EN 382-2-1993 | 纖維板 表面吸收性測定 第2部分：硬質板試驗方法 | Fibreboards - Determination of surface absorption - Part 2: Test method for hardboards |
| EN 40-7-2002 | 燈柱 第7部分：纖維增強聚合物燈柱規范 | Lighting columns - Part 7: Requirements for fibre reinforced polymer composite lighting columns |
| EN 492-1994+A1-1999+AC-1996 | 屋面用的纖維水泥條板及其配件 產品規范和試驗方法 | Fibre-cement slates and their fittings for roofing; product specification and test methods / Note: To be replaced by prEN 492 (2003-07). |
| EN 494-1994+A1-1999+AC-1996 | 屋面用的纖維水泥型板及其配件 產品規范和試驗方法 | Fibre-cement profiled sheets and fittings for roofing; product specification and test methods / Note: To be replaced by prEN 494 (2003-07). |
| EN 50053-3-1989 | 使用易燃材料的靜電噴涂器的選擇、安裝和使用要求 第3部分：能量極限為0.24mJ 或5mJ的手持靜電纖維填料噴 | Requirements for the selection, installation and use of electrostatic spraying equipment for flammable materials - Part 3: Hand - held electrostatic flock spray guns with an energy limit of 0,24 mJ or 5 mJ and their associated apparatus |
| EN 50353-2001 | 絕緣油 通過顯微鏡記數法測定纖維污染 | Insulating oil - Determination of fibre contamination by the counting method using a microscope |
| EN 512-1994+A1-2001 | 纖維水泥制品 壓力管道和接頭 | Fibre-cement products - Pressure pipes and joints |
| EN 588-1-1996 | 污水管和排水管用纖維水泥管 第1部分：重力系統用管道、管連接件和管配件 | Fibre-cement pipes for sewers and drains - Part 1: Pipes, joints and fittings for gravity systems |
| EN 588-2-2001 | 污水管和排水管用纖維水泥管 第2部分：檢修孔和檢查室 | Fibre cement pipes for drains and sewers - Part 2: Manholes and inspection chambers |
| EN 59-1977 | 玻璃纖維增強塑料 用 Barcol壓痕方法測量硬度 | Glass reinforced plastics - Measurement of hardness by means of a Barcol impressor |
| EN 60249-2-1-1994+A2-1994+A3-1995+A4-2000 | 印制電路用基材 第2-1部分：高電氣質量的酚醛纖維素紙覆銅層壓板 | Base materials for printed circuits; part 2: specifications; specification No. 1: phenolic cellulose paper copper-clad laminated sheet, high electrical quality (IEC 60249-2-1:1985 + A1:1989) |
| EN 60249-2-14-1994+A3-1994+A4-1995+A5-2000 | 印制電路用基材 第2-14部分：規范 阻燃型酚醛纖維素紙覆銅層壓板（垂直燃燒試驗） 經濟型 | Base materials for printed circuits; part 2: specifications; specification no. 14: phenolic cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test), economic quality (IEC 60249-2-14:1988 + A2:1990) |
| EN 60249-2-2-1994+A3-1994+A4-1995+A5-2000 | 印制電路用基材 第2-2部分：規范 酚醛纖維素紙覆銅箔層壓板 經濟型 | Base materials for printed circuits; part 2: specifications; specification No. 2: phenolic cellulose paper copper-clad laminated sheet, economic quality (IEC 60249-2-2:1985 + A2:1990) |
| EN 60249-2-3-1994+A2-1994+A3-1995+A4-2000 | 印制電路用基材 第2-3部分：規范 阻燃型環氧化物纖維素紙覆銅層壓板（垂直燃燒試驗） | Base materials for printed circuits; part 2: specifications; specification No. 3: epoxide cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test) (IEC 60249-2-3:1987 + A1:1989) |
| EN 60249-2-6-1994+A3-1994+A4-1995+A5-2000 | 印制電路用基材 第2-6部分：規范 阻燃型酚醛纖維素紙覆銅層壓板（水平燃 燒試驗） | Base materials for printed circuits; part 2: specifications; specification No. 6: phenolic cellulose paper copper-clad laminated sheet of defined flammability (horizontal burning test) (IEC 60249-2-6:1985 + A1:1989) |
| EN 60249-2-7-1994+A3-1994+A4-1995+A5-2000 | 印制電路用基材 第2-7部分：規范 阻燃型酚醛纖維素紙覆銅層壓板（垂直燃燒試驗） | Base materials for printed circuits; part 2: specifications; specification No. 7: phenolic cellulose paper copper-clad laminated sheet of defined flammability (vertical burning test) (IEC 60249-2-7:1987 + A1:1989) |
| EN 60249-2-9-1994+A3-1994+A4-1995+A5-2000 | 印制電路用基材 第2-9部分：規范 阻燃型環氧化物纖維素紙芯、環氧化物玻璃布表面覆銅層壓板（垂直燃燒試 | Base materials for printed circuits; part 2: specifications; specification No. 9: epoxide cellulose paper core, epoxide glass cloth surfaces copper-clad laminated sheet of defined flammability (vertical burning test) (IEC 60249-2-9:1987 + A1:1989 + A2:19 |
| EN 60454-3-10-1995 | 電工用壓敏粘帶 第3部分：單項材料規范 活頁10：涂橡膠熱固性粘合劑的乙酸丁酸纖維素薄膜膠粘帶的要求 | Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 10: Requirements for cellulose-acetate-butyrate film tapes with rubber thermosetting adhesive (IEC 60454-3-10:1995) |
| EN 60454-3-11-1998 | 電氣用壓敏膠粘帶 第3部分：單項材料規范 活頁11：涂橡膠熱固性粘合劑的纖維素皺紋紙與聚對苯二甲酸乙二 | Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 11: Combined tapes made of creped cellulosic paper and polyethylene terephthalate film with rubber thermosetting adhesive (IEC 60454-3-11) |
| EN 60454-3-13-1995 | 電工用壓敏粘帶 第3部分：單項材料規范 活頁13：一面涂覆熱塑材料、另一面涂橡膠熱固性粘合劑的復合纖維 | Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 13: Requirements for combined cellulose-viscose woven fabric tapes, on side covered with a thermoplastic material, the other side with rub |
| EN 60454-3-4-1998 | 電氣用壓敏粘帶 第3部分：單項材料規范 活頁4：涂橡膠執固性粘合劑的纖維素皺紋紙 | Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 4: Cellulosic paper, creped, with rubber thermosetting adhesive (IEC 60454-3-4:1998) |
| EN 60454-3-5-1998 | 電氣用壓敏膠粘帶 第3部分：單項材料規范 活頁5：涂橡膠熱固性粘合劑的纖維素非皺紋紙 | Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 5: Cellulosic paper, non-creped, with rubber thermosetting adhesive (IEC 60454-3-5:1998) |
| EN 60454-3-9-1998 | 電氣用壓敏感膠粘帶 第3部分：單項材料規范 活頁9：涂橡膠熱固性粘合劑的醋酯纖維素織布帶 | Pressure-sensitive adhesive tapes for electrical purposes - Part 3: Specifications for individual materials - Sheet 9: Cellulose acetate woven fabric tapes with rubber thermosetting adhesive (IEC 60454-3-9:1998) |
| EN 60554-2-2002 | 電學用的纖維紙－第2部分：試驗方法 | Cellulosic papers for electrical purposes - Part 2: Methods of test (IEC 60554-2:2001) |
| EN 60601-2-4-2003 | 醫療電氣設備 第2-4部分：心臟除纖維顫動器安全性的特殊要求 | Medical electrical equipment - Part 2-4: Particular requirements for the safety of cardiac defibrillators (IEC 60601-2-4:2002) / Note: Endorsement notice |
| EN 60684-3-300-2002 | 絕緣軟套管 第3部分：各種型號套管規范 活頁300：無涂層的玻璃纖維編織套管 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheet 300: Glass textile fibre sleeving, braided, uncoated (IEC 60684-3-300:2002) / Note: Endorsement notice |
| EN 60684-3-400 bis 402-2002 | 絕緣軟套管 第3部分：各種型號套管規范 活頁400至402：有硅橡膠涂層的玻璃纖維紡織套管 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheets 400 to 402: Glass textile sleeving with silicone elastomer coating (IEC 60684-3-400 to 402:2002) / Note: Endorsement notice |
| EN 60684-3-403 bis 405-2002 | 絕緣軟套管 第3部分：各種型號套管規范 活頁403-405：丙烯酸脂玻璃纖維編織套管 | Flexible insulating sleeving - Part 3: Specification for individual types of sleeving; Sheets 403 to 405: Glass textile sleeving with acrylic based coating (IEC 60684-3-403 to 405:2002) / Note: Endorsement notice |
| EN 60684-3-406 bis 408-2003 | 絕緣軟套管 第3部分：各種型號套管規范 活頁406-408：有PVC涂層的玻璃纖維紡`織套管 | Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving; Sheets 406 to 408: Glass textile sleeving with PVC coating (IEC 60684-3-406 to 408:2003) / Note: Endorsement notice |
| EN 60684-3-409-1999 | 絕緣軟套管 第3部分：各種型號套管規范 活頁409：聚胺脂(PUR)涂覆層的玻璃纖維軟管 | Flexible insulating sleeving - Part 3: Specification for individual types of sleeving - Sheet 409: Glass textile sleeving with polyurethane (PUR)-based coating (IEC 60684-3-409:1999) |
| EN 60793-1-20-2002 | 光學纖維 第1-20部分：測量方法和試驗規程 纖維幾何結構 | Optical fibres - Part 1-20: Measurement methods and test procedures; Fibre geometry (IEC 60793-1-20:2001) |
| EN 60793-1-21-2002 | 光學纖維 第1-21部分：測量方法和試驗規程 被覆層幾何結構 | Optical fibres - Part 1-21: Measurement methods and test procedures - Coating geometry (IEC 60793-1-21:2001) |
| EN 60793-1-22-2002 | 光學纖維 第1-22部分：測量方法和試驗規程 長度測定 | Optical fibres - Part 1-22: Measurement methods and test procedures - Length measurement (IEC 60793-1-22:2001) |
| EN 60793-1-30-2002 | 光學纖維 第1-30部分：測量方法和試驗規程 纖維驗證試驗 | Optical fibres - Part 1-30: Measurement methods and test procedures; Fibre proof test (IEC 60793-1-30:2001) |
| EN 60793-1-31-2002 | 光學纖維 第1-31部分：測量方法和試驗規程 抗拉強度 | Optical fibres - Part 1-31: Measurement methods and test procedures; Tensile strength (IEC 60793-1-31:2001) |
| EN 60793-1-33-2002 | 光學纖維 第１－３３部分：測量方法和試驗規程 應力腐蝕敏感度 | Optical fibres - Part 1-33: Measurement methods and test procedures - Stress corrosion susceptibility (IEC 60793-1-33:2001) |
| EN 60793-1-34-2002 | 光學纖維 第１－３４部分：測量方法和試驗規程 纖維扭曲 | Optical fibres - Part 1-34: Measurement methods and test procedures; Fibre curl (IEC 60793-1-34:2001) |
| EN 60793-1-41-2002 | 光學纖維 第１－４１部分：測量方法和試驗規程 帶寬 | Optical fibres - Part 1-41: Measurement methods and test procedures; Bandwidth (IEC 60793-1-41:2001) |
| EN 60793-1-42-2002 | 光學纖維 第１－４２部分：測量方法和試驗規程 色散 | Optical fibres - Part 1-42: Measurement methods and test procedures; Chromatic dispersion (IEC 60793-1-42:2001) |
| EN 60793-1-43-2002 | 光學纖維 第１－４３部分：測量方法和試驗規程 數值孔徑 | Optical fibres - Part 1-43: Measurement methods and test procedures; Numerical aperture (IEC 60793-1-43:2001) |
| EN 60793-1-44-2002 | 光學纖維 第１－４４部分：測量方法和試驗規程 截止波長 | Optical fibres - Part 1-44: Measurement methods and test procedures; Cut-off wavelength (IEC 60793-1-44:2001) |
| EN 60793-1-46-2002 | 光學纖維 第１－４６部分：測量方法和試驗規程 光透射比變化的監測 | Optical fibres - Part 1-46: Measurement methods and test procedures; Monitoring of changes in optical transmittance (IEC 60793-1-46:2001) |
| EN 60793-1-47-2002 | 光學纖維 第１－４７部分：測量方法和試驗規程 宏彎曲損耗 | Optical fibres - Part 1-47: Measurement methods and test procedures; Macrobending loss (IEC 60793-1-47:2001) |
| EN 60793-1-50-2002 | 光學纖維 第１－５０部分：測量方法和試驗規程：濕熱（穩態） | Optical fibres - Part 1-50: Measurement methods and test procedures; Damp heat (steady state) (IEC 60793-1-50:2001) |
| EN 60793-1-51-2002 | 光學纖維 第１－５１部分：測量方法和試驗規程 干熱 | Optical fibres - Part 1-51: Measurement methods and test procedures; Dry heat (IEC 60793-1-51:2001) |
| EN 60793-1-52-2002 | 光學纖維 第１－５２部分：測量方法和試驗規程 溫度變化 | Optical fibres - Part 1-52: Measurement methods and test procedures; Change of temperature (IEC 60793-1-52:2001) |
| EN 60793-1-53-2002 | 光學纖維 第１－５３部分：測量方法和試驗規程 浸水 | Optical fibres - Part 1-53: Measurement methods and test procedures; Water immersion (IEC 60793-1-53:2001) |
| EN 60793-2-10-2002 | 光學纖維 第2-10部分：產品規范 A1類多模光纖的分規范 | Optical fibres - Part 2-10: Product specifications; Sectional specification for category A1 multimode fibres (IEC 60793-2-10:2002) / Note: To be replaced by prEN 60793-2-10 (2003-08). |
| EN 60793-2-20-2002 | 光學纖維 第2-20部分：產品規范 A2類多模光纖的分規范 | Optical fibres - Part 2-20: Product specifications; Sectional specification for category A2 multimode fibres (IEC 60793-2-20:2001) |
| EN 60793-2-30-2002 | 光學纖維 第2-30部分：產品規范 A3類多模光纖的分規范 | Optical fibres - Part 2-30: Product specifications; Sectional specification for category A3 multimode fibres (IEC 60793-2-30:2002) |
| EN 60793-2-40-2002 | 光學纖維 第2-40部分：產品規范 A4類多模光纖的分規范 | Optical fibres - Part 2-40: Product specifications; Sectional specification for category A4 multimode fibres (IEC 60793-2-40:2002) |
| EN 60793-2-50-2002 | 光學纖維 第2-50部分：產品規范 B級單模光纖的分規范 | Optical fibres - Part 2-50: Product specifications; Sectional specification for class B single-mode fibres (IEC 60793-2-50:2002) |
| EN 60794-1-1-2002 | 光學纖維電纜 第１－１部分：總規范 總則 | Optical fibre cables - Part 1-1: Generic specification; General (IEC 60794-1-1:2001) |
| EN 60794-1-2-1999+A-2002 | 光學纖維電纜 第1-2部分：總規范 光纜基本試驗程序 | Optical fibre cables - Part 1-2: General specification - Basic optical cable test procedures (IEC 60794-1-2:1999) |
| EN 60794-1-2/prA2-2002 | 光學纖維電纜 第1-2部分：總規范 光纜基本試驗程序 修改草案２ | Optical fibre cables - Part 1-2: Generic specification; Basic optical cable test procedures |
| EN 60794-3-20-2002 | 光學纖維電纜 第3-20部分：室外電纜 自立式架空通訊光纜的族規范 | Optical fibre cables - Part 3-20: Outdoor cables; Family specification for optical self-supporting aerial telecommunication cables (IEC 60794-3-20:2002, modified) / Note: Endorsement notice |
| EN 60794-3-2002 | 光學纖維電纜 第３部分：分規范 戶外電纜 | Optical fibre cables - Part 3: Sectional specification; Outdoor cables (IEC 60794-3:2001) |
| EN 60819-1-1995+A1-1996 | 電工用非纖維素紙 第１部分：定義和一般要求 | Non-cellulosic papers for electrical purposes - Part 1: Definitions and general requirements (IEC 60819-1:1995) |
| EN 60819-2-2001 | 電工用非纖維素紙 第２部分：試驗方法 | Non-cellulosic papers for electrical purposes - Part 2: Methods of test (IEC 60819-2:2001) |
| EN 60819-3-1-2001 | 電工用非纖維素紙 第３部分：單項材料規范 活頁１：填了料的玻璃紙 | Non-cellulosic papers for electrical purposes - Part 3: Specifications for individual materials; Sheet 1: Filled glass paper (IEC 60819-3-1:2001) |
| EN 60819-3-2-2001 | 電工用非纖維素紙 第2部分：單項材料規范 活頁2:紙的無機有機混合物 | Non-cellulosic papers for electrical purposes - Part 3: Specifications for individual materials; Sheet 2: Hybrid inorganic-organic paper (IEC 60819-3-2:2001) |
| EN 60819-3-4-2001 | 電工用非纖維素紙 第3部分：單項材料規范 活頁4：含云母顆粒不大于50%的芳族聚酰胺纖維紙 | Non-cellulosic papers for electrical purposes - Part 3: Specifications for individual materials; Sheet 4: Aramid fibre paper containing not more than 50 % of mica particles (IEC 60819-3-4:2001) |
| EN 60869-1-2000 | 纖維光學衰減器 第１部分：一般規范 | Fibre optic attenuators - Part 1: Generic specification (IEC 60869-1:1999) |
| EN 60874-17-1997 | 光纖和電纜的接頭 第１７部分：纖維光學接頭的部分規范 F-05型(磨擦鎖定) | Connectors for optical fibres and cables - Part 17: Sectional specification for fibre optic connector - Type F-05 (friction lock) (IEC 60874-17:1995 + Corrigendum 1996) |
| EN 60875-1-1-1998 | 纖維光學分流裝置 第１－１部分：空白詳細規格 | Fibre optic branching devices - Part 1-1: Blank detail specification (IEC 60875-1-1:1996) |
| EN 60875-1-2001 | 纖維光學分流裝置 第１部分：總規范 | Non-wavelength-selective fibre optic branching devices - Part 1: Generic specification (IEC 60875-1:2000) |
| EN 60876-1-2001 | 纖維光學開關 第１部分：總規范 | Fibre optic spatial switches - Part 1: Generic specification (IEC 60876-1:2001) |
| EN 61067-1-1997 | 玻璃和玻璃聚酯纖維編織帶規范 第1部分：定義、分類和一般要求 | Specification for glass and glass polyester fibre woven tapes - Part 1: Definitions, classification and general requirements (IEC 61067-1:1991) |
| EN 61067-2-1997 | 玻璃和玻璃聚酯纖維編織帶成 第2部分：試驗方法 | Specification for glass and glass polyester fibre woven tapes - Part 2: Methods of test (IEC 61067-2:1992) |
| EN 61067-3-1-1995 | 玻璃和玻璃聚酯纖維編織帶 第3部分：單項材料規范 活頁1：1,2,3 型織帶 | Glass and glass polyester fibre woven tapes - Part 3: Specifications for individual materials - Sheet 1: Type 1, 2 and 3 tapes (IEC 61067-3-1:1995) |
| EN 61068-1-1997 | 聚酯纖維機織帶 第1部分：定義、名稱和一般要求 | Specification for polyester fibre woven tapes - Part 1: Definitions, designation and general requirements (IEC 61068-1:1991) |
| EN 61068-2-1997 | 聚酯纖維編織帶規范 第2部分：試驗方法 | Specification for polyester fibre woven tapes - Part 2: Methods of test (IEC 61068-2:1991) |
| EN 61068-3-1-1995 | 聚酯纖維編織帶 第3部分：單項材料規范 活頁1：常規織機或無梭織機編織帶 | Polyester fibre woven tapes - Part 3: Specifications for individual materials - Sheet 1: Tapes woven on conventional or shuttleless looms (IEC 61068-3-1:1995) |
| EN 61197-1994 | 絕緣油 直線火焰蔓延 使用玻璃纖維帶的試驗方法 | Insulating liquids - Linear flame propagation - Test method using a glass-fibre tape (IEC 61197:1993) |
| EN 61202-1-2000 | 纖維光學隔離器 第1部分：通用規范 | Fibre optic isolators - Part 1: Generic specification (IEC 61202-1:2000) |
| EN 61249-2-18-2002 | 印制板和其它互連結構材料 第2-18部分：包被和非包被增強基材 阻燃型(垂直燃燒試驗)銅包被的非編織玻璃 | Materials for printed boards and other interconnecting structures - Part 2-18: Reinforced base materials, clad and unclad; Polyester non-woven fibreglass reinforced laminated sheet of defined flammability (vertical burning test), copper-clad (IEC 61249-2 |
| EN 61249-2-19-2002 | 印制板和其它互連結構用材料 第2-19部分：包被和非包被增強基材 阻燃型(垂直燃燒試驗)銅包被的交叉簾布 | Materials for printed boards and other interconnection structures - Part 2-19: Reinforced base materials, clad and unclad; Epoxide cross-plied linear fibreglass-reinforced laminated sheet of defined flammability (vertical burning test), copper-clad (IEC |
| EN 61249-2-4-2002 | 印制板和其它互連結構用材料 第2-4部分：包被和非包被增強基材 阻燃型(垂直燃燒試驗)銅包被的聚酯非編織/ | Materials for printed boards and other interconnecting structures - Part 2-4: Reinforced base materials, clad and unclad; Polyester non-woven/woven fiberglass laminated sheet of defined flammability (vertical burning test), copper-clad (IEC 61249-2-4:200 |
| EN 61249-2-8-2003 | 印制板和其它互連結構用材料 第2-8部分：包被和非包被增強基材 阻燃銅包被改進型溴化環氧編織玻璃纖維增 | Materials for printed boards and other interconnecting structures - Part 2-8: Reinforced base materials, clad and unclad; Modified brominated epoxide woven fiberglass reinforced laminated sheets of defined flammability (vertical burning test), copper-cla |
| EN 61280-1-4-2003 | 光纖通信子系統試驗程序 第1-4部分：一般通信子系統 多模纖維激光發射機的雙維近場數據的收集和整理 | Fibre optic communication subsystem test procedures - Part 1-4: General communication subsystems; Collection and reduction of two-dimensional nearfield data for multimode fibre laser transmitters (IEC 61280-1-4:2003) / Note: Endorsement notice |
| EN 61300-2-4-1997 | 光纖互連器件和無源元件 基本試驗和測量程序 第2-4部分：試驗 纖維/電纜保持力 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-4: Tests - Fibre/cable retention (IEC 61300-2-4:1995) |
| EN 61300-3-23-1998 | 光纖互連器件和無源元件 基本試驗和測量程序 第3-23部分：檢查和測量 纖維與套管端面間的相對位置 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-23: Examination and measurements - Fibre position relative to ferrule endface (IEC 61300-3-23:1998) |
| EN 61300-3-24-2000 | 光纖互連器件和無源元件 基本試驗和測量程序 第3-24部分：檢查和測量 偏振保持纖維的光學連接器鍵入準確 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-24: Examinations and measurements - Keying accuracy of optical connectors for polarization maintaining fibre (IEC 61300-3-24:1999) |
| EN 61300-3-25-1997 | 光纖互連器件和無源元件 基本試驗和測量程序 第3-25部分：檢查和測量 套管和裝有纖維套管的同心度 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-25: Examinations and measurements - Concentricity of the ferrules and ferrules with fibre installed (IEC 61300-3-25:1997) |
| EN 61300-3-26-2002 | 光纖互連器件和無源元件 基本試驗和測量程序 第3-26部分：檢查和測量 纖維和套圈軸向間角偏差的測量 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-26: Examinations and measurements; Measurement of the angular misalignment between fibre and ferrule axes (IEC 61300-3-26:2002) / Note: Endorsemen |
| EN 61300-3-30-2003 | 光纖互連設備和無源元件 基本試驗和測量程序 第3-30部分：檢驗和測量 單套圈多纖維連接器磨光角度和纖維 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-30: Examinations and measurements; Polish angle and fibre position on single ferrule multifibre connectors (IEC 61300-3-30:2003) / Note: Endorseme |
| EN 61753-051-3-2002 | 光纖互連器件和無源元件性能標準 第051-3部分：U類單模纖維插栓型固定衰減器 非受控環境 | Fibre optic interconnecting devices and passive components performance standard - Part 051-3: Single-mode fibre, plug-style fixed attenuators for category U; Uncontrolled environment (IEC 61753-051-3:2001) |
| EN 622-1-2003 | 纖維板 規范 第1部分：一般要求 | Fibreboards - Specifications - Part 1: General requirements |
| EN 622-2-1997 | 纖維板 規范 第2部分：硬質板的要求 | Fibreboards - Specifications - Part 2: Requirements for hardboards |
| EN 622-3-1997 | 纖維板 規范 第3部分：中度板的要求 | Fibreboards - Specifications - Part 3: Requirements for medium boards |
| EN 622-4-1997 | 纖維板 規范 第4部分：軟質板的要求 | Fibreboards - Specifications - Part 4: Requirements for softboards |
| EN 622-5-1997 | 纖維板 規范 第5部分：干燥處理板的要求 | Fibreboards - Specifications - Part 5: Requirements for dry process boards (MDF) |
| EN 696-1995 | 一般用途纖維繩索 聚酰胺繩索 | Fibre ropes for general service - Polyamide |
| EN 697-1995 | 一般用途纖維繩索 聚酯繩索 | Fibre ropes for general service - Polyester |
| EN 698-1995 | 一般用途纖維繩索 粗麻繩和劍麻繩 | Fibre ropes for general service - Manila and sisal |
| EN 699-1995 | 一般用途纖維繩索 聚丙烯繩 | Fibre ropes for general service - Polypropylene |
| EN 700-1995 | 一般用途纖維繩索 聚乙烯繩 | Fibre ropes for general service - Polyethylene |
| EN 701-1995 | 一般用途纖維繩索 總規范 | Fibre ropes for general service - General specification |
| EN 705-1994 | 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管和配件 回歸分析及其使用方法 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analysis and their use |
| EN 766-1994 | 食品運輸袋 黃麻纖維編織袋 | Sacks for the transport of food aid - Sacks made of jute fabric |
| EN 872-1996 | 水質 懸浮微粒的測定 玻璃纖維過濾器過濾法 | Water quality - Determination of suspended solids - Method by filtration through glass fibre filters |
| EN 919-1995 | 一般用途纖維繩索 某些物理和力學性能的測定 | Fibre ropes for general service - Determination of certain physical and mechanical properties |
| EN ISO 10350-2-2001 | 塑料 可比單點數據的采集和表示 第2部分：長纖維增強塑料 | Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2001) |
| EN ISO 10352-1997 | 纖維增強塑料 模塑料和預浸料 單位面積質量的測定 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area (ISO 10352:1997) |
| EN ISO 105-Z03-1998 | 紡織品 色牢度試驗 第Z03部分：聚丙烯腈纖維用堿性染料的互溶性 | Textiles - Tests for colour fastness - Part Z03: Intercompatibility of basic dyes for acrylic fibres (ISO 105-Z03:1996) |
| EN ISO 10548-2003 | 碳纖維 膠含量的測定 | Carbon fibre - Determination of size content (ISO 10548:2002) |
| EN ISO 1061-1999 | 塑料 未贈塑的乙酸纖維素 游離酸度的測定 | Plastics - Unplasticized cellulose acetate - Determination of free acidity (ISO 1061:1990) |
| EN ISO 10618-1999 | 碳纖維 樹脂浸漬紗拉伸性能的測定 | Carbon fibre - Determination of tensile properties of resin-impregnated yarns (ISO 10618:1999) |
| EN ISO 1157-1999 | 塑料 稀溶液中的乙酸纖維 粘度值和粘度率的測定 | Plastics - Cellulose acetate in dilute solution - Determination of viscosity number and viscosity ratio (ISO 1157:1990) |
| EN ISO 11667-1999 | 纖維增強塑料 模塑料和預浸料 樹脂、增強纖維和礦物質填料含量的測定 溶解法 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of resin, reinforced-fibre and mineral-filler content - Dissolution methods (ISO 11667:1997) |
| EN ISO 1172-1998 | 紡織玻璃纖維增強塑料、預浸料、模塑料和層壓塑料紡織玻璃纖維和礦物質填料含量的測定 煅燒法 | Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content - Calcination methods (ISO 1172:1996) |
| EN ISO 11721-1-2001 | 紡織品 纖維素紡織品抗菌性的測定 弄臟法 第1部分：防腐處理的評定 | Textiles - Determination of resistance of cellulose-containing textiles to micro-organisms - Soil burial test - Part 1: Assessment of rot-retardant finishing (ISO 11721-1:2001) |
| EN ISO 11721-2-2003 | 紡織品 紡織品中纖維素抗細菌生長力的測定 弄臟法 第2部分：長期保持干凈阻力的識別 | Textiles - Determination of resistance of cellulose containing textiles to microorganisms; Soil burial test - Part 2: Identification of long-term resistance of a rot retardant finish (ISO 11721-2:2003) |
| EN ISO 12114-1997 | 纖維增強塑料 熱固性模壓塑料和預浸料 固化特性的測定 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of cure characteristics (ISO 12114:1997) |
| EN ISO 12115-1997 | 纖維增強塑料 熱固性模壓塑料和預浸料 流動性、熟化期和適用期的測定 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of flowability, maturation and shelf life (ISO 12115:1997) |
| EN ISO 12215-1-2000 | 小艇 船體結構和尺寸 第1部分：材料：熱固性樹脂、玻璃纖維增強材料、基準層壓板 | Small craft - Hull construction and scantlings - Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate (ISO 12215-1:2000) |
| EN ISO 13002-1998 | 碳纖維 長絲紗命名體系 | Carbon fibre - Designation system for filament yarns (ISO 13002:1998) |
| EN ISO 14125-1998 | 纖維增強塑料復合材料 彎曲性能的測定 | Fibre-reinforced plastic composites - Determination of flexural properties (ISO 14125:1998) |
| EN ISO 14126-1999 | 纖維增強塑料復合材料 平面方向壓縮性的測定 | Fibre-reinforced plastic composites - Determination of compressive properties in the in-plane direction (ISO 14126:1999) |
| EN ISO 14129-1997 | 纖維增強塑料復合材料 用±45°張力試驗法測定平面剪應力/剪應變特性、包括平面切變模量和剪切強度 | Fibre-reinforced plastic composites - Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by ?45°tension test method (ISO 14129:1997) |
| EN ISO 14130-1997 | 纖維增強塑料復合材料 用短試片法測定表觀層間粘合剪切強度 | Fibre-reinforced plastic composites - Determination of apparent interlaminar shear strength by short-beam method (ISO 14130:1997) |
| EN ISO 14692-1-2002 | 石油和天然氣工業 玻璃纖維增強塑料管 第1部分：詞匯、符號、設備和材料 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2002) |
| EN ISO 14692-2-2002 | 石油和天然氣工業 玻璃纖維增強塑料管 第2部分：資格和制造 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002) |
| EN ISO 14692-3-2002 | 石油和天然氣工業 玻璃纖維增強塑料管 第3部分：系統設計 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2002) |
| EN ISO 14692-4-2002 | 石油和天然氣工業 玻璃纖維增強塑料管 第4部分：制造 、安裝和運行 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2002) |
| EN ISO 1597-1999 | 塑料 未増塑的乙酸纖維 乙酸量的測定 | Plastics - Unplasticized cellulose acetate - Determination of acetic acid yield (ISO 1597:1994) |
| EN ISO 1598-1999 | 塑料 乙酸纖維素 不溶物的測定 | Plastics - Cellulose acetate - Determination of insoluble particles (ISO 1598:1990) |
| EN ISO 1599-1999 | 塑料 乙酸纖維素 模塑時粘度降低的測定 | Plastics - Cellulose acetate - Determination of viscosity loss on moulding (ISO 1599:1990) |
| EN ISO 1600-1999 | 塑料 乙酸纖維素 利用熱的不同循環在生產模制樣品中吸收量的測定 | Plastics - Cellulose acetate - Determination of light absorption on moulded specimens produced using different periods of heating (ISO 1600:1990) |
| EN ISO 1856-2000 | 可素纖維素聚合材料 壓縮裝置測定 | Flexible cellular polymeric materials - Determination of compression set (ISO 1856:2000) |
| EN ISO 1886-1994 | 增強纖維 適用于接收批料的抽樣方案 | Reinforcement fibres - Sampling plans applicable to received batches (ISO 1886:1990) |
| EN ISO 1973-1995 | 紡織纖維 線密度的測定 稱重和振動法 | Textile fibres - Determination of linear density - Gravimetric method and vibroscope method (ISO 1973:1995) |
| EN ISO 5079-1995 | 紡織纖維 單纖維斷裂強力和伸長率的測定 | Textiles - Fibres - Determination of breaking force and elongation at break of individual fibres (ISO 5079:1979) |
| EN ISO 527-4-1997 | 塑料 拉伸性能的測定 第4部分：各向同性及各向異性纖維增強塑料復合材料試驗條件 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:1997) |
| EN ISO 527-5-1997 | 塑料 拉伸性能的測定 第5部分：單向纖維增強塑料復合材料試驗條件 | Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:1997) |
| EN ISO 5350-1-1998 | 紙漿 塵埃和纖維束的估算 第1部分：實驗室紙張檢驗 | Pulp - Estimation of dirt and shives - Part 1: Inspection of laboratory sheets (ISO 5350-1:1998) |
| EN ISO 5350-2-1998 | 紙漿 塵埃和纖維束的估算 第2部分：磨木漿片檢驗 | Pulp - Estimation of dirt and shives - Part 2: Inspection of mill sheeted pulp (ISO 5350-2:1998) |
| EN ISO 585-1999 | 塑料 未增塑的乙酸纖維素 水分含量的測定 | Plastics - Unplasticized cellulose acetate - Determination of moisture content (ISO 585:1990) |
| EN ISO 6865-2000 | 動物飼料 粗纖維含量的測定 中級過濾法 | Animal feeding stuffs - Determination of crude fibre content - Method with intermediate filtration (ISO 6865:2000) |
| EN ISO 6888-2-1999+A1-2003 | 食品和動物飼料的微生物學 凝血酶陽性葡萄球菌(金黃色葡萄球菌及其他種)計數的水平方法 第2部分：兔血漿 | Microbiology of food and animal feeding stuffs - Horizontal method for the enumeration of coagulase-positive staphylococci (Staphylococcus aureus and other species) - Part 2: Technique using rabbit plasma fibrinogen agar medium (ISO 6888-2:1999) |
| EN ISO 75-3-1996 | 塑料 載荷下?lián)锨鷾囟鹊臏y定 第3部分：高強度熱固性疊層板和長纖維增強塑料 | Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics (ISO 75-3:1993) |
| EN ISO 7822-1999 | 玻璃纖維增強塑料 孔隙率的測定 燒失量、機械粉碎和靜態計數法 | Textile glass reinforced plastics - Determination of void content - Loss on ignition, mechanical disintegration and statistical counting methods (ISO 7822:1990) |
| EN ISO 9163-1998 | 紡織玻璃纖維 粗紗 試樣的制備和浸漬粗紗拉伸強度的測定 | Textile glass - Rovings - Manufacture of test specimens and determination of tensile strength of impregnated rovings (ISO 9163:1996) |
| ENV 1094-7-1993 | 絕緣耐火產品 第7部分：陶瓷纖維產品試驗方法 | Insulating refractory products - Part 7: Methods of test for ceramic fibre products |
| ENV 1170-8-1996 | 玻璃纖維增強水泥試驗方法 第8部分：循環風化類型試驗 | Test method for glass-fibre reinforced cement - Part 8: Cyclic weathering type test |
| prEN 12064-1996 | 木板 包裝用實心和波紋纖維板規范 | Board - Specification of solid and corrugated fibreboard for packaging purposes |
| prEN 12917-1997 | 玻璃纖維加強塑料（GRP）制地下罐 用于液體石油燃料無壓貯存的臥式柱罐 EN976-1和EN976-3的符合性評價 | Underground tanks of glass-reinforced plastics (GRP) - Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels - Assessment of conformity to EN 976-1 and EN 976-3 |
| prEN 13002-3-1998 | 碳纖維絲線 第3部分：技術規范 | Carbon filament yarns - Part 3: Technical specifications |
| prEN 13421-1999 | 塑料 熱塑復合物 合成材料和加強纖維 用于測定壓塑復合材料性能各向異性的樣品制備 | Plastics - Thermoset moulding compounds - Composites and reinforcement fibres - Preparation of specimens for determining the anisotropy of the properties of compression moulding composites |
| prEN 13815-2000 | 纖維狀石膏產品 定義、要求、試驗方法 | Fibrous gypsum plaster products - Definitions, requirements and test methods |
| prEN 13923-2000 | 繞制玻璃纖維加強塑料（FRP）壓力容器 材料、設計、計算、制造和試驗 | Filament wound FRP pressure vessels - Materials, design, calculation, manufacturing and testing |
| prEN 13978-2-2000 | 預制混凝土產品 預制混凝土車庫 第2部分：鋼纖維混凝土車庫，產品性能及使用情況 | Precast concrete products - Precast concrete garages - Part 2: Steel fibre concrete garages; Product properties and performances |
| prEN 14196-2003 | 土工合成纖維織物 粘土土工合成織物隔離物單位面積質量的測試驗方法 | Geosynthetics - Test methods for measuring mass per unit area of clay geosynthetic barriers |
| prEN 14278-1-2003 | 紡織品 棉纖維粘性測定 第1部分：用人工測熱器法 | Textiles - Determination of cotton fibre stickiness - Part 1: Method using a manual thermodetection device |
| prEN 14364-2002 | 有或無壓排水和排污塑料管線系統 玻璃纖維增強的未飽和的聚酯樹脂基熱固塑料管 塑料管管件及接頭規范 | Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints |
| prEN 14447-2002 | 纖維增強塑料 玻璃墊增強熱塑塑料 液動性和固化測定 | Fibre reinforced plastics - Glass mat reinforced thermoplastics (GMT) - Determination of flowability and solidification |
| prEN 1445-2000 | 纖維水泥管道 現場壓力試驗 | Fibre-cement pipelines - Field pressure testing |
| prEN 1492-4-2001 | 織物吊索 安全性 第4部分：用天然和人造纖維繩制造的一般用途提升吊索 | Textile slings - Safety - Part 4: Lifting slings for general service made from natural and man-made fibre ropes |
| prEN 1636-1-1996 | 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第1部分：總則 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General |
| prEN 1636-2-1996 | 無壓力排水道和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第2部分：帶有撓 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints |
| prEN 1636-4-1994 | 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第4部分：輔助設備 | Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment |
| prEN 1796-3-1995 | 有或無壓力供水用塑料管道系統聚合物樹脂（UP）基玻璃纖維增強熱固性塑料（GRP） 第3部分：管件 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 3: Fittings |
| prEN 1796-4-1995 | 有或無壓力供水有塑料管道系統聚合物樹脂（UP）基玻璃纖維增強熱固性塑料（GRP） 第4部分：輔助設備 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment |
| prEN 1796-5-1995 | 有或無壓力供水用塑料管道系統聚合物樹脂（UP）基玻璃纖維增強熱固性塑料（GRP） 第5部分：系統用途的適合 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 5: Fitness for the purpose of the system |
| prEN 1796-6-1995 | 有或無壓力供水用塑料管道系統聚合物樹脂（UP）基玻璃纖維增強熱固性塑料（GRP） 第6部分：推薦的安裝實踐 | Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 6: Recommended practice for installation |
| prEN 23-1-1989 | 洗滌粉和清潔粉的包裝 纖維板硬紙盒和圓筒的尺寸和體積 | Packages for washing and cleaning powders; dimensions and volumes of cartons and drums from fibre board |
| prEN 2823-1998 | 航空航天系列 纖維增強塑料 暴露于潮濕環境對物理和機械性能影響的測定 | Aerospace series - Fibre reinforced plastics - Determination of the effect of exposure to humid atmosphere on physical and mechanical characteristics |
| prEN 2833-1-1997 | 航空航天系列 玻璃纖維增強熱固預浸漬物 技術規范 第１部分：一般要求 | Aerospace series - Glass fibre thermosetting preimpregnates - Technical specification - Part 1: General requirements |
| prEN 2833-3-1997 | 航空航天系列 玻璃纖維熱固預浸漬物 技術規范 第３部分：塑化溫度達180 ℃ 、持續使用達120℃玻璃纖維／ | Aerospace series - Glass fibre thermosetting preimpregnates - Technical specification - Part 3: Glass fabric/epoxy resin preimpregnate curing at up to 180℃ for continuous use up to 120℃ |
| prEN 2833-4-1997 | 航空航天系列 玻璃纖維熱固預浸漬物 技術規范 第４部分：塑化溫度達125 ℃、持續使用達 80 ℃單向玻璃／ | Aerospace series - Glass fibre thermosetting preimpregnates - Technical specification - Part 4: Unidirectional glass/epoxy resin preimpregnate curing at up to 125℃ for continuous use up to 80℃ |
| prEN 2833-5-2001 | 航空航天系列 玻璃纖維熱固預浸漬物 技術規范 第５部分：玻璃纖維／酚醛樹脂預浸漬物 | Aerospace series - Glass fibre thermosetting preimpregnates; Technical specification - Part 5: Glass fabric/phenolic resin preimpregnate |
| prEN 2850-1997 | 航空航天系列 碳纖維增強熱固樹脂單向疊層板 平衡纖維方向的壓縮測試 | Aerospace series - Carbon fibre thermosetting resin unidirectional laminates - Compression test parallel to fibre direction |
| prEN 302-3-2001 | 承重木結構用膠粘劑 試驗方法 第3部分：通過溫度和濕度循環試驗測定酸性腐蝕對木纖維橫向拉伸強度的影響 | Adhesives for load-bearing timber structures - Test methods - Part 3: Determination of the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile strength |
| prEN 30306-1994 | 紡織品 棉纖維 成熟度的氣流法評定 | Textiles - Cotton fibres - Evaluation of maturity by the air flow method (ISO 10306:1993) |
| prEN 3615-1998 | 航空航天系列 纖維增強塑料 暴露于潮濕環境和水分吸收條件的測定 | Aerospace series - Fibre reinforced plastics - Determination of the conditions of exposure to humid atmosphere and of moisture absorption |
| prEN 3745-202-1999 | 航空航天系列 航空用光纜光纖 試驗方法 第202部分：纖維尺寸 | Aerospace series - Fibres and cables, optical, aircraft use - Test methods - Part 202: Fibre dimensions |
| prEN 4238-1998 | 航空航天系列 纖維增強塑料 干熱對物理和機械特性的影響的測定 | Aerospace series - Fibre reinforced plastics - Determination of the effect of dry heat on physical and mechanical characteristics |
| prEN 6049-001-2001 | 航空航天系列 設備電纜 偏聚酸胺纖維保護套 第001部分：技術規范 | Aerospace series - Electrical cables, installation; Protection sleeve in meta-aramid fibres - Part 001: Technical specification |
| prEN 6049-006-2001 | 航空航天系列 設備電纜 偏聚酸胺纖維保護套 第006部分：自動包裝保護套 易彎曲接線端裝置 產品標準 | Aerospace series - Electrical cables, installation; Protection sleeve in meta-aramid fibres - Part 006: Self-wrapping protective sleeve, flexible post installation; Product standard |
| prEN 60793-1-3-2000 | 光學纖維 第１－３部分：總規范 機械性能試驗方法 草案 | Optical fibres - Part 1-3: Generic specification; Measuring methods for mechanical characteristics (IEC 60793-1-3:2000, modified) |
| prEN 60793-1-32-2001 | 光學纖維 第1-32部分：測量方法和試驗規程 被覆層可剝性 草案 | IEC 60793-1-32, Ed. 1: Optical fibres - Part 1-32: Measurement methods and test procedures; Coating strippability |
| prEN 60793-1-40-2001 | 光學纖維 第１－４０部分：測量方法和試驗規程 衰減 草案 | IEC 60793-1-40, Ed. 1: Optical fibres - Part 1-40: Measurement methods and test procedures; Attenuation |
| prEN 60793-1-41-2003 | 光學纖維 第１－４１部分：測量方法和試驗規程 帶寬 草案 | IEC 60793-1-41, Ed. 2.0: Optical fibres - Part 1-41: Measurement methods and test procedures; Bandwidth |
| prEN 60793-1-45-2001 | 光學纖維 第１－４５部分：測量方法和試驗規程 模場直徑 草案 | IEC 60793-1-45, Ed. 1: Optical fibres - Part 1-45: Measurement methods and test procedures; Mode field diameter |
| prEN 60793-1-49-2003 | 光學纖維 第１－４９部分：測量方法和試驗規程 | IEC 60793-1-49, Ed. 1.0: Optical fibres - Part 1-49: Measurement methods and test procedures; Differential mode delay |
| prEN 60794-4-1-1998 | 光學纖維電纜 第４－１部分：高壓輸電線架空電纜 | IEC 60794-4-1: Optical fibre cables - Part 4-1: Aerial optical cables for high voltage power lines |
| prEN 60794-4-2003 | 光學纖維電纜 第４部分：高壓輸電線架空電纜 | IEC 60794-4, Ed. 2.0: Optical fibre cables - Part 4: Sectional specification; Aerial optical cables along electrical power lines |
| prEN 61249-2-1-2002 | 印制板和其它互連結構用材料 第2-1部分：包被和非包被增強基材分規范集 酚醞纖維紙增強層壓薄板、經濟級 | IEC 61249-2-1, Ed. 1: Materials for printed boards and other interconnection structures - Part 2-1: Sectional specification set for reinforced base materials, clad and unclad; Phenolic cellulose paper reinforced laminate sheet, economic grade,copper clad |
| prEN 61249-2-2-2002 | 印制板和其它互連結構用材料 第2-2部分：包被和非包被增強基材分規范集 酚醞纖維紙增強層壓板、強電級、 | IEC 61249-2-2: Materials for printed boards and other interconnection structures - Part 2-2: Sectional specification set for reinforced base materials, clad and unclad; Phenolic cellulose paper reinforced laminate, high electrical grade, copper clad |
| prEN 61249-2-5-2003 | 印制板和其它互連結構用材料 第2-5部分：包被和非包被增強基材分規范集 阻燃型(垂直燃燒試驗)銅包被的溴 | IEC 61249-2-5, Ed. 1: Materials for printed boards and other interconnection structures - Part 2-5: Reinforced base materials, clad and unclad; Brominated epoxide cellulose paper reinforced core/woven E-glass reinforced surfaces laminated sheets of defin |
| prEN ISO 10468-1999 | 塑料管 玻璃纖維增增強熱固塑料管 在濕環境中長期特殊環形蠕變勁度的測定及濕蠕變因子的計算 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor (ISO/DIS 10468:1999) |
| prEN ISO 10618-2002 | 碳纖維 樹脂浸漬紗拉伸性能的測定 | Carbon fibre - Determination of tensile properties of resin-impregnated yarn (ISO/DIS 10618:2002) |
| prEN ISO 14828-1999 | 塑料管道系統 玻璃纖維增強熱固塑料管 在濕環境下長期特殊環形松弛勁度的測定和濕松弛系數的計算 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor (ISO/DIS 14828:1999) |
| prEN ISO 1968-2003 | 纖維繩索和繩索制品 詞匯 | Fibre ropes and cordage - Terms and Definitions (ISO/FDIS 1968:2003) |
| prEN ISO 75-3-2003 | 塑料 載荷下?lián)锨鷾囟鹊臏y定 第3部分：高強度熱固性疊層板和長纖維增強塑料 | Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates (ISO/FDIS 75-3:2003) / Note: Intended as replacement for EN ISO 75-3 (1996-02). |
| 編號 | 中文名稱 | 英文名稱 |