| 編號 | 中文名稱 | 英文名稱 |
|---|
| BS 1425-1-1991
| 床上用品、室內裝飾品和其他家用制品的填充料的清潔度.羽毛/羽絨除外的填充料規范
| Cleanliness of fillings and stuffings for bedding, upholstery and other domestic articles - Specification for fillings and stuffings other than feather and/or down
|
| BS 3900-F17-1998
| 涂料試驗方法.第F節：涂料膜的耐久性試驗.第17部分：涂層耐濕刮和清潔度的測定
| Methods of test for paint. Durability tests on paint films. Determination of wet-scrub resistance and cleanability of coatings
|
| BS 5295-0-1989
| 封閉空間環境清潔度.第0部分:凈室和凈化空氣裝置總則、術語和定義
| Environmental cleanliness in enclosed spaces - General introduction, terms and definitions for clean rooms and clean air devices
|
| BS 598 Pt.101-1987
| 道路和其他鋪砌區用瀝青混合料的取樣和檢查.第101部分:分析樣品的預處理方法
| Sampling and examination of bituminous mixtures for roads and other paved areas. Methods for preparatory treatments of samples for analysis
|
| BS 598-101-2004
| 道路和其他鋪筑區用瀝青混合料的取樣和檢驗.分析用樣品的預處理方法
| Sampling and examination of bituminous mixtures for roads and other paved areas - Methods for preparatory treatments of samples for analysis
|
| BS 7079-A1 Supplement 1-1996
| 涂料和有關產品涂層前鋼基片的制備.第A1集:表面清潔度目測評定.第1部分:采用不同磨料進行噴沙除銹時鋼片表
| Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Representative photographic examples of the change of appearance imparted to steel when blast-cleaned with different abrasives
|
| BS 7079-A1-1989
| 涂料和有關產品應用前鋼基片的制備.表面清潔度視覺評定.未涂層鋼基片和鋼基片全部清除原涂層以后生銹程度和
| Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Specification for rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
|
| BS 7079-A2-1996
| 涂料和有關產品涂層前鋼基片的制備.第A2集:表面清潔度目測評定.第1部分:局部清除原涂層后原涂層的鋼片底基
| Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Preparation grades of previously coated steel substrates after localized removal of previous coatings
|
| BS 7079-A3-2002
| 涂料和有關產品使用前鋼襯底的制備.表面清潔度的目視評定.焊接點、切割邊緣及其他表面缺陷區域的處理等級
| Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Preparation grades of welds, cut edges and other areas with surface imperfections - A3: Preparation grades of welds, cut edges and other areas with surface imperfections
|
| BS 7079-B2-1992
| 涂料和有關產品使用前鋼基片的制備.第B2部分:表面清潔度的評定方法.在清潔的表面上氯化物的測定方法
| Preparation of steel substrates before application of paints and related products. Methods for the assessment of surface cleanliness. Method for determination of chlorides on cleaned surfaces
|
| BS 7079-B3-1993
| 涂料和有關產品應用前鋼基片的制備.表面清潔度評定方法.第B3部分:準備涂層(壓敏帶方法)的鋼基面塵垢評定
| Preparation of steel substrates before application of paints and related products. Methods for the assessment of surface cleanliness. Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method)
|
| BS 7079-B4-1993
| 涂料和有關產品應用前鋼基片的制備.表面清潔度評定方法. 第B4部分:待涂表面冷凝概率估算指南
| Preparation of steel substrates before application of paints and related products. Methods for the assessment of surface cleanliness. Guide to the estimation of the probability of condensation on a surface to be painted
|
| BS 7079-B6-1996
| 涂料和有關產品應用前鋼襯底的制備.表面清潔度評定方法.分析用可溶性污染物的提取.第B6部分:布列斯(Bresle)
| Preparation of steel substrates before application of paints and related products. Methods for the assessment of surface cleanliness. Extraction of soluble contaminants for analysis. The Bresle method
|
| BS 7079-B8-2001
| 涂料和有關產品使用之前鋼襯底的制備.表面清潔度的評定方法.現場用折射計測定濕度法
| Preparation of steel substrates before application of paints and related products - Methods for the assessment of surface cleanliness - Field method for the refractometric determination of moisture
|
| BS 7079-B9-1998
| 涂料和有關產品應用前鋼襯底的制備.表面清潔度評定方法.第B9部分：水溶性鹽熱導測定的現場方法
| Preparation of steel substrates before application of paints and related products. Methods for the assessment of surface cleanliness. Field method for the conductometric determination of water-soluble salts
|
| BS 7755-3.5-1995
| 土質.化學方法.物理化學分析取樣預處理
| Soil quality - Chemical methods - Pretreatment of samples for physico-chemical analyses
|
| BS DD ENV ISO 8502-1-1992
| 涂料和相關產品涂敷之前鋼基材的備制處理. 表面清潔度的評估試驗.可溶解鐵腐蝕產品的現場試驗
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Field test for soluble iron corrosion products
|
| BS EN 12255-3-2000
| 污水處理廠.預處理
| Wastewater treatment plants - Preliminary treatment
|
| BS EN 12921-2-2005
| 使用液體或蒸氣的工業設備的表面清潔和預處理機器.使用水基清潔液的機械的安全
| Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Safety of machines using water based cleaning liquids
|
| BS EN 12921-3-2005
| 使用液體或蒸氣的工業設備的表面清潔和預處理機器.使用易燃清潔液體的機器的安全性
| Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Safety of machines using flammable cleaning liquids
|
| BS EN 12921-4-2005
| 使用液體或蒸氣的工業設備的表面清潔和預處理機器.使用鹵化溶劑的機械的安全
| Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Safety of machines using halogenated solvents
|
| BS EN 13507-2001
| 熱噴涂.熱噴涂元件和金屬零部件表面預處理
| Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying
|
| BS EN 13946-2003
| 水質.河水中底棲硅藻類常規取樣和預處理的指導性標準
| Water quality - Guidance standard for the routine sampling and pretreatment of benthic diatoms from rivers
|
| BS EN 14694-2005
| 防水用柔性薄板.車輛可通過的混凝土船橋甲板和其他混凝土路面的防水.預處理產生損壞后耐動態水壓的測定
| Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of resistance to dynamic water pressure after damage by pre-treatment
|
| BS EN 50176-1997
| 易燃液體噴涂材料用自動靜電噴涂裝置
| Automatic electrostatic spraying installations for flammable liquid spraying material
|
| BS EN 50177-1997
| 易燃噴涂粉末用自動靜電噴涂裝置
| Automatic electrostatic spraying installations for flammable coating powder
|
| BS EN ISO 11124-3-1994
| 涂料和其他相關產品應用前鋼基體的預處理.噴射金屬清理磨料的規范.高碳鑄鋼丸和砂
| Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - High-carbon cast-steel shot and grit
|
| BS EN ISO 11124-4-1994
| 用涂層材料涂覆前鋼基體的預處理.噴射金屬清理磨料的規范.低碳鑄鋼丸
| Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Low-carbon cast-steel shot
|
| BS EN ISO 11125-1-1994
| 涂料和相關產品使用前鋼基體的預處理.噴射金屬清潔磨料的試驗方法.抽樣
| Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Sampling
|
| BS EN ISO 11125-2-1994
| 涂料和相關產品使用前鋼基體的預處理.噴射金屬清理磨料的試驗方法.粒度分布測定
| Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Determination of particle size distribution
|
| BS EN ISO 11125-3-1994
| 涂料和相關產品使用前鋼基體的預處理.噴射金屬清理磨料的試驗方法.硬度測定
| Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Determination of hardness
|
| BS EN ISO 11125-4-1994
| 涂料和相關產品使用前鋼基體的預處理.噴射金屬清理磨料的試驗方法.表觀密度的測定
| Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Determination of apparent density
|
| BS EN ISO 11125-5-1994
| 涂料和相關產品使用前鋼基體的預處理.噴射金屬清理磨料的試驗方法.缺陷顆粒的百分比和微結構的測定
| Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Determination of percentage defective particles and of microstructure
|
| BS EN ISO 11125-6-1994
| 涂料和相關產品使用前鋼基體的預處理.噴射金屬清理磨料的試驗方法.外來雜質測定
| Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Determination of foreign matter
|
| BS EN ISO 11125-7-1994
| 涂料和相關產品使用前鋼基體的預處理.噴射金屬清理磨料的試驗方法.濕度測定
| Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Determination of moisture
|
| BS EN ISO 11126-1-1997
| 涂料和其它相關產品應用前鋼底基的預處理.非金屬噴砂清理磨料規范.概述和分類
| Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - General introduction and classification
|
| BS EN ISO 11126-10-2000
| 涂裝油漆和有關產品前鋼材預處理.噴射清理用非金屬磨料規范.鐵鋁石榴石
| Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Almandite garnet
|
| BS EN ISO 11126-3-1994
| 涂料和其他相關產品應用前鋼基體的預處理. 噴非金屬清理磨料規范.銅精煉廠爐渣
| Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Copper refinery slag
|
| BS EN ISO 11126-4-1994
| 涂料和其它相關產品應用前鋼基體的預處理.非金屬噴砂清理磨料規范.煤爐熔渣
| Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Coal furnace slag
|
| BS EN ISO 11126-5-1994
| 涂料和其他相關產品應用前鋼基體的預處理.非金屬噴砂清理磨料規范.鎳精練廠礦渣
| Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Nickel refinery slag
|
| BS EN ISO 11126-6-1994
| 涂料和其它相關產品應用前鋼基體的預處理.噴非金屬清理磨料規范.煉鐵爐爐渣
| Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Iron furnace slag
|
| BS EN ISO 11126-8-1994
| 涂料和其它相關產品應用前鋼基體的預處理. 噴非金屬清理磨料規范.橄欖石砂
| Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Olivine sand
|
| BS EN ISO 11126-9-1999
| 涂裝油漆和有關產品前鋼襯底預處理.噴射清理用非金屬磨料的規范.十字石
| Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Staurolite
|
| BS EN ISO 11127-1-1994
| 涂料和其它相關產品應用前鋼基體的預處理. 噴非金屬清理磨料試驗方法.制樣
| Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Sampling
|
| BS EN ISO 11127-2-1994
| 涂料和其它相關產品應用前鋼基體的預處理. 噴非金屬清理理磨料試驗方法.微粒規格分布測定
| Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Determination of particle size distribution
|
| BS EN ISO 11127-3-1994
| 涂料和其它相關產品應用前鋼基體的預處理. 噴非金屬清理磨料試驗方法.表觀密度的測定
| Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Determination of apparent density
|
| BS EN ISO 11127-4-1994
| 涂料和相關產品應用前鋼基體的預處理. 非金屬噴砂清理磨料試驗方法.用玻璃劃痕試驗評估硬度
| Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Assessment of hardness by a glass slide test
|
| BS EN ISO 11127-5-1994
| 涂料和相關產品應用前鋼基體的預處理. 非金屬噴砂清理磨料試驗方法.濕度的測定
| Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Determination of moisture
|
| BS EN ISO 11127-6-1994
| 涂料和相關產品應用前鋼基體的預處理. 非金屬噴砂清理磨料試驗方法.用電導性測量測定水溶性雜質
| Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Determination of water-soluble contaminants by conductivity measurement
|
| BS EN ISO 11127-7-1994
| 涂料和相關產品應用前鋼基體的預處理. 非金屬噴砂清理磨料試驗方法.水溶性氯化物的測定
| Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Determination of water-soluble chlorides
|
| BS EN ISO 14644-1-1999
| 潔凈室和相關的控制環境.空氣清潔度的分級
| Cleanrooms and associated controlled environments - Classification of air cleanliness
|
| BS EN ISO 8501-1 Supplement-1996
| 涂油漆和有關產品前鋼基底預處理.表面清潔度的目視評定.不同磨料噴射清理所致鋼材表觀改變的典型樣板照片
| Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Representative photographic examples of the change of appearance imparted to steel when blast-cleaned with different abrasives
|
| BS EN ISO 8501-1-1989
| 涂油漆和有關產品前鋼基底預處理.表面清潔度的目視評定.未涂鋼基底和全面清除原有涂層后鋼基底材的銹蝕等級
| Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
|
| BS EN ISO 8501-2-1996
| 涂油漆和有關產品前鋼基底預處理.表面清潔度的目視評定.局部去除原有涂層后鋼基底的處理等級
| Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Preparation grades of previously coated steel substrates after localized removal of previous coatings
|
| BS EN ISO 8502-10-2000
| 涂料和有關產品使用前鋼襯底的制備.表面清潔度的評定試驗.水溶性氯化物的現場滴定測定方法
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Field method for the titrimetric determination of water-soluble chloride
|
| BS EN ISO 8502-12-2003
| 涂料和有關產品使用前鋼襯底的制備.表面清潔度的評定試驗.水溶性亞鐵離子的現場滴定測定方法
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Field method for the titrimetric determination of water-soluble ferrous ions
|
| BS EN ISO 8502-2-2006
| 涂裝油漆和相關產品前鋼材的預處理.表面清潔度的評定試驗.實驗室測定清潔表面上氯化物
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Laboratory determination of chloride on cleaned surfaces
|
| BS EN ISO 8502-3-1993
| 涂料和有關產品使用前鋼襯底的制備.表面清潔度的評定試驗.涂漆鋼表面粉塵評定(壓敏帶法)
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method)
|
| BS EN ISO 8502-4-1993
| 涂料和有關產品使用前鋼襯底的制備.表面清潔度的評定試驗.涂覆前的冷凝可能性評定導則
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Guidance on the estimation of the probability of condensation prior to paint application
|
| BS EN ISO 8502-5-2005
| 涂裝油漆和有關產品前鋼材的預處理.表面清潔度的評定試驗.涂裝前鋼材表面上氯化物的測定(離子探測管法)
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Measurement of chloride on steel surfaces prepared for painting (ion detection tube method)
|
| BS EN ISO 8502-6-1996
| 涂料和有關產品使用前鋼襯底的制備.表面清潔度的評定試驗.Bresle法分析用可溶性雜質的析取
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Extraction of soluble contaminants for analysis - The Bresle method
|
| BS EN ISO 8502-8-2001
| 涂料和有關產品使用前鋼襯底的制備.表面清潔度的評定試驗.濕度折射測定的現場方法
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Field method for the refractometric determination of moisture
|
| BS EN ISO 8502-9-1998
| 涂料和有關產品使用前鋼襯底的制備.表面清潔度評定試驗.水溶性鹽電導測定的現場方法
| Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Field method for the conductometric determination of water-soluble salts
|
| BS EN ISO 8503-5-2003
| 涂裝油漆和有關產品前鋼材預處理.噴射清理鋼材的表面粗糙度特性.表面輪廓測定的復制帶法
| Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Replica tape method for the determination of the surface profile
|
| BS EN ISO 9692-2-1998
| 焊接和相關工藝.接頭的預處理.鋼的埋弧焊
| Welding and allied processes - Joint preparation - Submerged arc welding of steels
|
| BS ISO 12345-2003
| 柴油發動機.燃料噴射設備的清潔度評定
| Diesel engines - Cleanliness assessment of fuel injection equipment
|
| BS ISO 12642-1997
| 圖形技術.預處理數字?jǐn)?shù)據交換.4種顏色彩色套印特性描述的輸入數據
| Graphic technology - Prepress digital data exchange - Input data for characterization of 4-colour process printing
|
| BS ISO 14507-2003
| 土質.有機污物測定用樣品的預處理
| Soil quality - Pretreatment of samples for determination of organic contaminants
|
| BS ISO 14952-1-2004
| 航天系統.液體系統的表面清潔度.詞匯
| Space systems - Surface cleanliness of fluid systems - Vocabulary
|
| BS ISO 14952-2-2004
| 航天系統.液體系統的表面清潔度.清潔度等級
| Space systems - Surface cleanliness of fluid systems - Cleanliness levels
|
| BS ISO 14952-3-2004
| 航天系統.液體系統的表面清潔度.不揮發性殘流物和顆粒污染物的測定用分析程序
| Space systems - Surface cleanliness of fluid systems - Analytical procedures for the determination of nonvolatile residues and particulate contamination
|
| BS ISO 14952-4-2004
| 航天系統.液體系統的表面清潔度.粗略清潔過程
| Space systems - Surface cleanliness of fluid systems - Rough-cleaning processes
|
| BS ISO 14952-5-2004
| 航天系統.液體系統的表面清潔度.干燥過程
| Space systems - Surface cleanliness of fluid systems - Drying processes
|
| BS ISO 14952-6-2004
| 航天系統.液體系統的表面清潔度.精確清潔過程
| Space systems - Surface cleanliness of fluid systems - Precision-cleaning processes
|
| BS ISO 18413-2002
| 液壓流體動力.零部件的清潔度.與污染收集、分析和數據報告相關的檢查文件和原則
| Hydraulic fluid power - Cleanliness of parts and components - Inspection document and principles related to contaminant collection , analysis and data reporting
|
| BS ISO 8503-5-2003
| 涂裝油漆和有關產品前鋼材預處理.噴射清理鋼材的表面粗糙度特性.表面輪廓測定的復制帶法
| Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Replica tape method for the determination of the surface profile
|
| BS ISO 9587-1999
| 金屬和其它無機覆層.鐵或鋼為減少氫脆危險的預處理
| Metallic and other inorganic coatings - Pretreatment of iron or steel to reduce the risk of hydrogen embrittlement
|
| PD 6609-2000
| 封閉式空間的環境清潔度.試驗方法指南
| Environmental cleanliness in enclosed spaces. Guide to test methods
|
| 編號 | 中文名稱 | 英文名稱 |
|---|