| 編號 | 中文名稱 | 英文名稱 |
|---|
| CR 12952-17-2002
| 鍋爐水管道和輔助設備 第17部分：獨立于制造商的檢查機構參與指南
| Water boilers and auxiliary installations - Part 17: Guideline for the involvement of an inspection body independent of the manufacturer
|
| CR 13932-2000
| 旋轉動力泵 管道系統的進口和出口管件建議書
| Rotodynamic pumps - Recommendations for fitting of inlet and outlet on piping
|
| EN 10208-1-1997
| 易燃流體管道用鋼管 交貨技術條件 第1部分：符合A類要求的管材
| Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 1: Pipes of requirement class A
|
| EN 10208-2-1996+AC-1996
| 易燃流體管道用鋼管 交貨技術條件 第2部分：符合B類要求的管材
| Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 2: Pipes of requirement class B
|
| EN 1053-1995
| 塑料管道系統 無壓力情況下使用的熱塑管道系統 水密封性的試驗方法
| Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness
|
| EN 1054-1995
| 塑料管道系統 糞便和污水排放用熱塑管道系統 連接件氣密性試驗方法
| Plastics piping systems - Thermoplastics piping systems for soil and waste discharge - Test method for airtightness of joints
|
| EN 1055-1996
| 塑料管道系統 建筑物內糞便和污水排放用熱塑管道系統 抗周期性升溫的試驗方法
| Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling
|
| EN 1093-6-1998
| 機械安全 空氣中有害物質排放的評估 第6部分：通過未經管道流出的質量來評價分離離效率
| Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 6: Separation efficiency by mass, unducted outlet
|
| EN 1093-7-1998
| 機械安全 空氣中有害物質排放的評估 第7部分：通過經管道流出的質量來評價分離離效率
| Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 7: Separation efficiency by mass, ducted outlet
|
| EN 1115-1-1997
| 壓力下地下排水和排污裝置用塑料管道系統 基于非飽和聚酯樹脂的玻璃增強熱固性塑料（GRP） 第1部分：概述
| Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General
|
| EN 1115-3-1996
| 壓力下地下排水和排污裝置用塑料管道系統 基于非飽和聚酯樹脂的玻璃增強熱固性塑料（GRP） 第3部分：配件
| Plastics piping systems for underground drainage and sewerage under pressure - Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings
|
| EN 1115-5-1996
| 壓力下地下排水和排污裝置用塑料管道系統 基于非飽和聚酯樹脂的玻璃增強熱固性塑料（GRP） 第5部分：連接
| Plastics piping systems for underground drainage and sewerage under pressure - Glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints
|
| EN 1119-1996
| 塑料管道系統 玻璃增強熱固塑料管和配件用接頭 撓性和還原接合接頭密封性和耐損傷性試驗方法
| Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of flexible and reduced-articulation joints
|
| EN 1120-1996
| 塑料管道系統 玻璃增強熱固塑料管和配件 偏斜條件下內部一個截面耐化學品侵襲的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition
|
| EN 1123-1-1999
| 廢水系統用帶套管的縱向焊接熱浸鍍鋅鋼管管道及配件 第1部分：要求、測試和質量控制
| Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control
|
| EN 1123-1/prA1-2002
| 廢水系統用帶套管的縱向焊接熱浸鍍鋅鋼管管道及配件 第1部分：要求、測試和質量控制 修改A1
| Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control; Amendment A1
|
| EN 1123-2-1999
| 廢水系統用帶套管和插口的縱向焊接熱浸鍍鋅鋼管管道及配件 第2部分：尺寸
| Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 2: Dimensions
|
| EN 1124-1-1999
| 廢水系統用帶套管和插口的縱向焊接不銹鋼管管道及配件 第1部分：要求、測試、質量控制
| Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control
|
| EN 1124-1/prA1-2002
| 廢水系統用帶套管和插口的縱向焊接不銹鋼管管道及配件 第1部分：要求、測試、質量控制 修改A1
| Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 1: Requirements, testing, quality control; Amendment A1
|
| EN 1124-2-1999
| 廢水系統用帶套管和插口的縱向焊接不銹鋼管管道和配件 第2部分：系統S 尺寸
| Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 2: System S - Dimensions
|
| EN 1124-3-1999
| 廢水系統用帶套管和插口的縱向焊接不銹鋼管管道及配件 第3部分：系統X 尺寸
| Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems - Part 3: System X - Dimensions
|
| EN 12056-2-2000
| 建筑物內的重力排水系統 第2部分：衛生間管道工程的布局和計算
| Gravity drainage systems inside buildings - Part 2: Sanitary pipework, layout and calculation
|
| EN 12061-1999
| 塑料管道系統 熱塑性管件 耐沖擊試驗方法
| Plastics piping systems - Thermoplastics fittings - Test method for impact resistance
|
| EN 12095-1997
| 塑料管道系統 雨水管道系統用托架 托架強度的試驗方法
| Plastics piping systems - Brackets for rainwater piping systems - Test method for bracket strength
|
| EN 12099-1997
| 塑料管道系統 聚乙烯管材和組件 揮發含量的測定
| Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
|
| EN 12100-1997
| 塑料管道系統 聚乙稀(PE)閥門 支架間抗彎曲性的試驗方法
| Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports
|
| EN 12106-1997
| 塑料管道系統 聚乙稀(PE)管 壓出后抗內壓性的試驗方法
| Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off
|
| EN 12107-1997
| 塑料管道系統 壓注熱塑管件、閥門和輔助設備 管道組件壓注用熱塑 材料的長期液壓強度的測定
| Plastics piping systems - Injection-moulded thermoplastics fittings, valves and ancillary equipment - Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components
|
| EN 12117-1997
| 塑料管道系統 熱塑管件、閥門和配件 氣流速率/壓降之間關系的測定
| Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships
|
| EN 12118-1997
| 塑料管道系統 用庫侖計測定熱塑性塑料中水分
| Plastics piping systems - Determination of moisture content in thermoplastics by coulometry
|
| EN 12119-1997
| 塑料管道系統 聚乙烯(PE)閥門 抗熱循環測試方法
| Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to thermal cycling
|
| EN 12200-1-2000
| 地面上外部使用的塑料雨水管道系統 未增塑聚乙烯（聚氯乙烯）（PVC-U） 第1部分：管道、配件和系統用規范
| Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
|
| EN 12201-1-2003
| 供水系統用塑料管道系統 聚乙烯（PE） 第1部分：總則
| Plastics piping systems for water supply - Polyethylene (PE) - Part 1: General
|
| EN 12201-2-2003
| 供水系統用塑料管道系統 聚乙烯（PE） 第2部分：管道
| Plastics piping systems for water supply - Polyethylene (PE) - Part 2: Pipes
|
| EN 12201-3-2003
| 供水系統用塑料管道系統 聚乙烯（PE） 第3部分：配件
| Plastics piping systems for water supply - Polyethylene (PE) - Part 3: Fittings
|
| EN 12201-4-2001
| 供水系統用塑料管道系統 聚乙烯（PE） 第4部分：閥門
| Plastics piping systems for water supply - Polyethylene (PE) - Part 4: Valves
|
| EN 12201-5-2003
| 供水系統用塑料管道系統 聚乙烯（PE） 第5部分：系統目的的適配性
| Plastics piping systems for water supply - Polyethylene (PE) - Part 5: Fitness for purpose of the system
|
| EN 12220-1998
| 建筑物通風 管道系統 一般通風用圓法蘭盤的測定
| Ventilation for buildings - Ductwork - Dimensions of circular flanges for general ventilation
|
| EN 12236-2002
| 建筑物通風 管道懸架和支架 強度需求
| Ventilation for buildings - Ductwork hangers and supports - Requirements for strength
|
| EN 12237-2003
| 建筑物通風 管道系統 圓片金屬管的強度和泄漏
| Ventilation for buildings - Ductwork - Strength and leakage of circular sheet metal ducts
|
| EN 1225-1996
| 塑料管道系統 玻璃增強熱固性塑料管 潮濕條件下蠕變因子的測定和長期特定環剛度的計算
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under wet conditions and calculation of the long-term specific ring stiffness
|
| EN 12256-1998
| 塑料管道系統 .熱塑性塑料配件 裝配式配件機械強度或撓度的試驗方法
| Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings
|
| EN 1226-1996
| 塑料管道系統 玻璃增強熱固性塑料管 驗證初期環狀物撓曲阻力的試驗方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection
|
| EN 1227-1997
| 塑料管道系統 玻璃增強熱固性塑料管 潮濕條件下長期最終相關環狀物撓曲的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term ultimate relative ring deflection under wet conditions
|
| EN 1228-1996
| 塑料管道系統 玻璃增強熱固性塑料管 初始特定環剛度的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness
|
| EN 1229-1996
| 塑料管道系統 玻璃增強熱固性塑料管 驗證短期內部壓力下墻的密封性試驗方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure
|
| EN 12293-1999
| 塑料管道系統 熱水和冷水用熱塑性塑料管道和接頭 安裝組件耐熱循環性的試驗方法
| Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling
|
| EN 12294-1999
| 塑料管道系統 熱水和冷水系統 真空下氣密性的試驗方法
| Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum
|
| EN 12295-1999
| 塑料管道系統 熱水和冷水用熱塑性塑料管道和接頭 接合處耐壓力循環試驗方法
| Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling
|
| EN 12308-1998
| 液化天然裝置和設備 液化天然氣管道中所用的法蘭接頭墊圈設計適配性試驗
| Installations and equipment for LNG - Suitability testing of gaskets designed for flanged joints used on LNG piping
|
| EN 12474-2001
| 水下管道的陰極保護
| Cathodic protection of submarine pipelines
|
| EN 12514-2-2000
| 燃油爐供油系統用的裝置 第２部分：安全要求和試驗 零部件、閥門、管道、濾油器、油氣分離器、油量指示表
| Installations for oil supply systems for oil burners - Part 2: Safety requirements and tests - Parts, valves, pipes, filters, oil de-aerators, meters
|
| EN 12585-1998
| 玻璃設備、管道和配件 DN15至1000管道和配件 兼容性和互換性
| Glass plant, pipeline and fittings - Pipeline and fittings DN 15 to 1000 - Compatibility and interchangeability
|
| EN 12735-1-2001
| 銅和銅合金 空調和制冷用無縫圓銅管 第１部分：管道系統用管子
| Copper and copper alloys - Seamless, round copper tubes for air conditioning and refrigeration - Part 1: Tubes for piping systems
|
| EN 1277-1996
| 塑料管道系統 地下無壓用熱塑管道系統 彈性密封環型接頭密封性試驗方法
| Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints
|
| EN 12842-2000
| PVC-U或PE管道系統用可球墨鑄鐵配件 要求和試驗方法
| Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods
|
| EN 1295-1-1997
| 不同荷載條件下地下管道結構設計 第1部分：一般要求
| Structural design of buried pipelines under various conditions of loading - Part 1: General requirements
|
| EN 12954-2001
| 掩埋或浸沒金屬結構的陰極保護 一般原理和管道應用
| Cathodic protection of buried or immersed metallic structures - General principles and application for pipelines
|
| EN 13052-1-2001
| 材料對人類生活用水的影響 有機物 管道系統中水的顏色和濁度的測定 第一部分：試驗方法
| Influence of materials on water intended for human consumption - Organic materials; Determination of colour and turbidity of water in piping systems - Part 1: Test method
|
| EN 13090-2000
| 建筑物中氣體管道螺紋接頭再密封方法
| Means for resealing threaded joints of gas pipework in buildings
|
| EN 13136-2001
| 制冷系統和加熱泵 壓力釋放設備及相關管道 計算方法
| Refrigerating systems and heat pumps - Pressure relief devices and their associated piping - Methods for calculation
|
| EN 13180-2001
| 建筑物通風 管道系統 柔性管的尺寸和機械要求
| Ventilation for buildings - Ductwork - Dimensions and mechanical requirements for flexible ducts
|
| EN 13220-1998
| 與醫用氣體管道系統的終端設備相連的流量計
| Flow-metering devices for connection to terminal units of medical gas pipeline systems
|
| EN 13244-1-2002
| 地上和地下給排水和污水壓力系統用塑料管道 聚已烯（PE） 第1部分：總則
| Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General
|
| EN 13244-2-2002
| 地上和地下給排水和污水壓力系統用塑料管道 聚已烯（PE） 第2部分：管道
| Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes
|
| EN 13244-3-2002
| 地上和地下給排水和污水壓力系統用塑料管道 聚已烯（PE） 第3部分：配件
| Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings
|
| EN 13244-4-2002
| 地上和地下給排水和污水壓力系統用塑料管道 聚已烯（PE） 第4部分：閥門
| Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves
|
| EN 13244-5-2002
| 地上和地下給排水和污水壓力系統用塑料管道 聚已烯（PE） 第5部分：系統適用度
| Plastics piping systems for buried and above-ground pressure systems for water of general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system
|
| EN 1329-1-1999
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 硬塑聚氯乙烯(PVC-U) 第1部分：管材、管件和系統規
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
|
| EN 13312-1-2001
| 生物技術 管道和儀器性能標準 第1部分：一般的性能標準
| Biotechnology - Performance criteria for piping and instrumentation - Part 1: General performance criteria
|
| EN 13312-2-2001
| 生物技術 管道和儀器性能標準 第2部分 聯接器
| Biotechnology - Performance criteria for piping and instrumentation - Part 2: Couplings
|
| EN 13312-3-2001
| 生物技術 管道和儀器性能標準 第3部分：取樣和接種裝置
| Biotechnology - Performance criteria for piping and instrumentation - Part 3: Sampling and inoculation devices
|
| EN 13312-4-2001
| 生物技術 管道和儀器性能標準 第4部分：管子和導管
| Biotechnology - Performance criteria for piping and instrumentation - Part 4: Tubes and pipes
|
| EN 13312-5-2001
| 生物技術 管道和儀器性能標準 第5部分：閥
| Biotechnology - Performance criteria for piping and instrumentation - Part 5: Valves
|
| EN 13312-6-2001
| 生物技術 管道和儀器性能標準 第6部分：設備探頭
| Biotechnology - Performance criteria for piping and instrumentation - Part 6: Equipment probes
|
| EN 1333-1996
| 管道工程元件 定義和PN的選擇
| Pipework components - Definition and selection of PN
|
| EN 13403-2003
| 建筑物通風 非金屬管道 由絕熱道管板制成的管道系統
| Ventilation for buildings - Non-metallic ducts - Ductwork made from insulation ductboards
|
| EN 13467-2001
| 建筑設備和工業裝置用保溫制品 預成型管道保溫層的尺寸、垂直度和直線度的測定
| Thermal insulating products for building equipment and industrial installations - Determination of dimensions, squareness and linearity of preformed pipe insulation
|
| EN 13469-2001
| 建筑設備和工業裝置用保溫制品 預成型管道保溫層水蒸氣傳導性的測定
| Thermal insulating products for building equipment and industrial installations - Determination of water vapour transmission properties of preformed pipe insulation
|
| EN 13470-2001
| 建筑設備和工業裝置用保溫制品 預成型管道保溫層表觀密度的測定
| Thermal insulating products for building equipment and industrial installations - Determination of the apparent density of preformed pipe insulation
|
| EN 13472-2001
| 建筑設備和工業裝置用保溫制品 通過部分沉浸法測定預成型管道保溫層的短期吸水性
| Thermal insulating products for building equipment and industrial installations - Determination of short term water absorption by partial immersion of preformed pipe insulation
|
| EN 13480-1-2002
| 工業用金屬管道 第1部分：總則
| Metallic industrial piping - Part 1: General
|
| EN 13480-2-2002
| 工業用金屬管道 第2部分：材料
| Metallic industrial piping - Part 2: Materials
|
| EN 13480-3-2002
| 工業用金屬管道 第3部分：設計和計算
| Metallic industrial piping - Part 3: Design and calculation
|
| EN 13480-4-2002
| 工業用金屬管道 第4部分：制造和安裝
| Metallic industrial piping - Part 4: Fabrication and installation
|
| EN 13480-5-2002
| 工業用金屬管道 第5部分：檢查和測試
| Metallic industrial piping - Part 5: Inspection and testing
|
| EN 13544-2-2002
| 呼吸治療設備 第2部分：管道和連接器
| Respiratory therapy equipment - Part 2: Tubing and connectors
|
| EN 13566-1-2002
| 用于修復非壓力排水和污水網的塑料管道系統 第1部分：總則
| Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General
|
| EN 13566-3-2002
| 用于修復非壓力排水和污水網的塑料管道系統 第3部分：帶密裝配管的襯套
| Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes
|
| EN 13566-4-2002
| 用于修復非壓力排水和污水網的塑料管道系統 第4部分：帶現場固化管的襯套
| Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes
|
| EN 13598-1-2003
| 非壓力底下排水和污水塑料管道系統 非增塑聚氯乙烯（PVC-U）、聚丙烯（PP）和聚乙烯（PE） 第1部分：包括
| Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings including shallow inspection chambers
|
| EN 1366-1-1999
| 服務設施的耐火試驗 第1部分：管道
| Fire resistance tests for service installations - Part 1: Ducts
|
| EN 1366-5-2003
| 服務設施的耐火試驗 第5部分：作業管道和煙囪
| Fire resistance tests for service installations - Part 5: Service ducts and shafts
|
| EN 13689-2002
| 用于修復的塑料管道系統的分類和設計指南
| Guidance on the classification and design of plastics piping systems used for renovation
|
| EN 1393-1996+AC-1997
| 塑料管道系統 玻璃增強熱固性塑料(GRP)管 初始徑向拉伸特性的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial longitudinal tensile properties
|
| EN 1394-1996+AC-1997
| 塑料管道系統 玻璃增強熱固性塑料(GRP)管 外觀初始圓周抗拉強度的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength
|
| EN 13942-2003
| 石油和天然氣工業 管道運輸系統 管道閥門
| Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:1999, modified)
|
| EN 1401-1-1998
| 非壓力地下雨水管和污水管用塑料管道系統未增塑聚氯乙烯(PVC-U) 管道 第1部分：配件和系統規范
| Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
|
| EN 1411-1996
| 塑料管道和導管系統 熱塑管 用階梯法測定抗外沖擊能力
| Plastics piping and ducting systems - Thermoplastics pipes - Determination of resistance to external blows by the staircase method
|
| EN 14163-2001
| 石油和天然氣工業 管道運輸系統 管道的焊接
| Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000, modified)
|
| EN 1420-1-1999
| 有機材料對民用水的影響 管道系統中水氣味的測定 第1部分：試驗方法
| Influence of organic materials on water intended for human consumption - Determination of odour and flavour assessment of water in piping systems - Part 1: Test method
|
| EN 1437-2002
| 塑料管道系統 地下排水和污水用管道系統 耐溫度循環和外部負荷綜合作用的試驗方法
| Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading
|
| EN 1444-2000
| 纖維水泥管道 現場工作實踐和鋪設指南
| Fibre-cement pipelines - Guide for laying and on-site work practices
|
| EN 1446-1996
| 塑料管道及導管系統 熱塑管 環撓形測定
| Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility
|
| EN 1447-1996
| 塑料管道系統 玻璃增強熱固性塑料管 (GRP) 長期耐內壓能力的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure
|
| EN 1448-1996
| 塑料管道系統 玻璃增強熱固塑料(GRP)組件 帶彈性密封件的剛性鎖緊插承接合的設計查驗試驗方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of rigid locked socket-and-spigot joints with elastomeric seals
|
| EN 1449-1996
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)組件 查檢水泥套管插承接合設計的試驗方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of cemented socket-and-spigot joints
|
| EN 1450-1996+A1-1998
| 塑料管道系統 玻璃增強熱固塑料(GRP)組件 螺栓法蘭連接的設計查驗試驗方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) components - Test methods to prove the design of bolted flange joints
|
| EN 1451-1-1998
| 建筑物結構內污物和廢水排出(低和高溫)用塑料管道系統 聚丙烯(PP ) 第1部分：管材、管件和系統規范
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
|
| EN 1452-1-1999
| 供水塑料管道系統 硬聚氯乙烯(PVC-U) 第1部分：總則
| Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General
|
| EN 1452-2-1999
| 供水塑料管道系統 硬聚氯乙烯(PVC-U) 第2部分：管材
| Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Pipes
|
| EN 1452-3-1999
| 供水塑料管道系統 硬聚氯乙烯(PVC-U) 第3部分：管件
| Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings
|
| EN 1452-4-1999
| 供水塑料管道系統 硬聚氯乙烯(PVC-U) 第4部分：閥門和附屬設備
| Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment
|
| EN 1452-5-1999
| 供水塑料管道系統 硬塑聚氯乙烯(PVC-U) 第5部分：系統的適合性
| Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system
|
| EN 1453-1-2000
| 建筑物內污物和廢水排放(低和高溫)帶結構壁管道的塑料管道系統 硬聚氯乙烯(PVC-U) 第1部分：管材和系統規
| Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system
|
| EN 1455-1-1999
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 丙烯腈 丁二烯 苯乙烯共聚物 第1部分：管材、管
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system
|
| EN 1456-1-2001
| 地上和地下污廢水壓力排放用塑料管道系統 硬已烯(聚氯已烯)(PVC-U) .第1部分：管道組件和系統規范
| Plastics piping systems for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for piping components and the system
|
| EN 1505-1997
| 建筑物通風 矩形截面的金屬片通風管道和管件 尺寸
| Ventilation for buildings - Sheet metal air ducts and fittings with rectangular cross section - Dimensions
|
| EN 1506-1997
| 建筑物通風 環形截面的金屬片通風管道和管件 尺寸
| Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions
|
| EN 1519-1-1999
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 聚乙烯(PE) 第1部分：管材、管件和系統規范
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
|
| EN 1555-1-2002
| 供給氣體燃料用塑料管道系統 聚已烯(PE) 第1部分：總則
| Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
|
| EN 1555-2-2002
| 供給氣體燃料用塑料管道系統 聚已烯(PE) 第2部分：管材
| Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes
|
| EN 1555-3-2002
| 供給氣體燃料用塑料管道系統 聚已烯(PE) 第3部分：管件
| Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
|
| EN 1555-4-2002
| 供給氣體燃料用塑料管道系統 聚已烯(PE) 第4部分：閥門
| Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4: Valves
|
| EN 1555-5-2002
| 供給氣體燃料用塑料管道系統 聚已烯(PE) 第5部分：針對系統用途的適合性
| Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 5: Fitness for purpose of the system
|
| EN 1565-1-1998
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 苯乙烯共聚混合物(SAN+PVC) 第1部分：管材、管件和
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system
|
| EN 1566-1-1998
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 氯化聚偏氯乙烯(PVC-C) 第1部分：管材、管件和系統
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
|
| EN 1594-2000
| 供氣系統 最大運行壓力超過16bar的管道 功能要求
| Gas supply systems - Pipelines for maximum operating pressure over 16 bar - Functional requirements
|
| EN 1636-3-1997
| 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第3部分：管件
| Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 3: Fittings
|
| EN 1636-5-1997
| 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第5部分：針對接頭
| Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 5: Fitness for purpose of the joints
|
| EN 1636-6-1997
| 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第6部分：安裝實踐
| Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation
|
| EN 1638-1997
| 塑料管道系統 玻璃增強熱固塑料管道(GRP) 循環內壓效果的試驗方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method for the effects of cyclic internal pressure
|
| EN 1680-1997
| 塑料管道系統 聚乙烯(PE)管道系統用閥門 傳動裝置的彎曲時和彎曲后密封性的試驗方法
| Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanism
|
| EN 1704-1997
| 塑料管道系統 熱塑閥門 彎曲情況下溫度周期變化后閥門完整性的試驗方法
| Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after temperature cycling under bending
|
| EN 1705-1996
| 塑料管道系統 熱塑閥門 外部鼓風后閥門完整性試驗方法
| Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow
|
| EN 1716-1997
| 塑料管道系統 聚乙烯(PE)分接三通管 分接三通管組件上耐沖擊能力的檢測方法
| Plastics piping systems - Polyethylene (PE) tapping tees - Test method for impact resistance of an assembled tapping tee
|
| EN 1775-1998+A1 -2000+A2-2000
| 供氣 建筑物中的氣體管道工程 最大運轉壓力≤5巴功能推薦
| Gas supply - Gas pipework for buildings - Maximum operating pressure 5 bar - Functional recommendations
|
| EN 1852-1-1997+A1-2001
| 無壓地下排水和污水用塑料管道系統 聚丙烯(PP)、 第一部分：管材、管件及系統規范
| Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
|
| EN 1861-1998
| 制冷系統和熱泵 系統流程圖和管道及儀表圖表 平面圖和符號
| Refrigerating systems and heat pumps - System flow diagrams and piping and instrument diagrams - Layout and symbols
|
| EN 1862-1997
| 塑料管道系統 玻璃增強熱固塑料管(GRP) 暴露在化學環境后相關撓曲蠕變因素的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the relative flexural creep factor following exposure to a chemical environment
|
| EN 187105-2002
| 單模光纖電纜(管道/直埋安裝)
| Single mode optical cable (duct/direct buried installation)
|
| EN 1905-1998
| 塑料管道系統 硬聚氯乙烯管、管件和材料 基于氯的總含量評估聚氯乙烯含量的方法
| Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content
|
| EN 1979-1999
| 塑料管道和管道系統 熱塑螺旋型結構壁的管材 接縫拉伸強度的測定
| Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam
|
| EN 1989-2000
| 熱塑性管道系統 埋地?zé)o壓污水用接頭 通過估計密封壓力對熱塑彈性塑料(TPE)密封接頭的長時間密封性能的試
| Thermoplastics piping systems - Joints for buried non-pressure sewerage applications - Test method for long-term sealing performance of joints with thermoplastic elastomer (TPE) seals by estimating the sealing pressure
|
| EN 24006-1993
| 封閉管道中液體流量的測量.名詞和符號
| Measurement of fluid flow in closed conduits; vocabulary and symbols (ISO 4006:1991)
|
| EN 24185-1993
| 封閉管道中液體流量的測量 重量法
| Measurement of liquid flow in closed conduits; Weighing method (ISO 4185:1980)
|
| EN 253-2003
| 分區供暖管 直接掩埋熱水網用預隔熱連接的管道系統 成套鋼鐵管道設備的管組件、聚氨酯熱絕緣和聚乙烯外覆
| District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene
|
| EN 288-9-1999
| 金屬材料焊接程序規范和鑒定 第9部分：傳輸管道陸地和海上場所對接焊中管道焊接用焊接程序試驗
| Specification and approval of welding procedures for metallic materials - Part 9: Welding procedure test for pipeline welding on land and offshore site butt welding of transmission pipelines
|
| EN 29104-1993
| 封閉管道中流體流量測量 液體電磁流量計性能評定方法
| Measurement of fluid flow in closed conduits; methods of evaluating the performance of electromagnetic flow-meters for liquids (ISO 9104:1991)
|
| EN 4028-2001
| 航空航天系列 鈦合金管連接 8°30′ 在管道上有推力絲螺母的三通
| Aerospace series - Pipe coupling 8?0 in titanium alloy - Tees with thrust wire nut on run
|
| EN 4030-2001
| 航空航天系列 鈦合金管連接 8°30′ 在管道上的Ｔ形艙壁
| Aerospace series - Pipe coupling 8?0 in titanium alloy - Tees bulkhead on run
|
| EN 4190-2001
| 空航天系列 鈦合金管連接8°30′ 管道上有推力絲螺母的異徑三通
| Aerospace series - Pipe coupling 8 Degree 30′in titanium alloy - Tees, reduced with thrust wire nut on run
|
| EN 448-2003
| 熱水分配管道 地下熱水網用預隔熱包覆層的管道系統 聚氨酯熱絕緣和聚乙烯外覆層的鋼鐵管的配件
| District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
|
| EN 45510-7-1-1999
| 發電站設備、設備和系統的采購指南 第7-1部分：管道系統和閥門 高壓管道系統
| Guide for procurement of power station plant, equipment, and systems - Part 7-1: Pipework and valves - High pressure piping systems
|
| EN 45510-7-2-1999
| 發電站設備、設備和系統的采購指南 第7-2部分：管道系統和閥門 鍋爐和高壓管道閥
| Guide for procurement of power station plant, equipment, and systems - Part 7-2: Pipework and valves - Boiler and high pressure piping valves
|
| EN 474-9-1998
| 土方機械 安全 第9部分：管道敷設機的要求
| Earth-moving machinery - Safety - Part 9: Requirements for pipelayers
|
| EN 476-1997
| 用于排水管道組件、重力系統的排水管的一般要求
| General requirements for components used in discharge pipes, drains and sewers for gravity systems
|
| EN 488-2003
| 熱水分配管道 地下熱水網用預先絕熱包覆的管道系統 成套鋼鐵管道設備的管閥門組件、聚氨酯熱絕緣和聚乙
| District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
|
| EN 489-2003
| 熱水分配管道 地下熱水網用預隔熱包覆的管道系統 成套鋼鐵管道設備的接頭組件、聚氨酯熱絕緣和聚乙烯外
| District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene
|
| EN 50085-1-1997+A1-1998
| 電氣裝置用電纜槽和電纜管道系統 第1部分：一般要求
| Cable trunking systems and cable ducting systems for electrical installations - Part 1: General requirements
|
| EN 50085-1/prA2-2002
| 電氣裝置用電纜槽和電纜管道系統 第1部分：一般要求 修改PrA2
| Cable trunking systems and cable ducting systems for electrical installations - Part 1: General requirements; Amendment A2
|
| EN 50085-2-3-1999
| 電氣裝置用電纜槽和電纜管道系統 第2-3部分：箱式設備用有槽電纜槽系統的特殊要求
| Cable trunking systems and cable ducting systems for electrical installations - Part 2-3: Particular requirements for slotted cable trunking systems intended for installation in cabinets
|
| EN 50249-2002
| 地下管道和電纜的定位器 性能與安全
| Electromagnetic locators for buried pipes and cables - Performance and safety
|
| EN 512-1994+A1-2001
| 纖維水泥制品 壓力管道和接頭
| Fibre-cement products - Pressure pipes and joints
|
| EN 545-2002
| 給水管道用球墨鑄鐵管、配件、附件及其接頭 要求和試驗方法
| Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods
|
| EN 578-1993
| 塑料管道系統 塑料管和配件 不透明度的測定
| Plastics piping systems - Plastics pipes and fittings - Determination of the opacity
|
| EN 579-1993
| 塑料管道系統 交聯聚乙烯(PE-X)管 溶劑萃取法測定交聯密度
| Plastics piping systems - rosslinked polyethylene (PE-X) pipes -Determination of degree of crosslinking by solvent extraction
|
| EN 580-2003
| 塑料管道系統 未增塑聚氯乙烯(PVC-U)管 特定溫度下耐二氯甲烷試驗方法
| Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT)
|
| EN 588-1-1996
| 污水管和排水管用纖維水泥管 第1部分：重力系統用管道、管連接件和管配件
| Fibre-cement pipes for sewers and drains - Part 1: Pipes, joints and fittings for gravity systems
|
| EN 60794-3-10-2002
| 光纖電纜 第3-10部分：室外電纜 管道和直接填埋的通訊光纜的族規范
| Optical fibre cables - Part 3-10: Outdoor cables; Family specification for duct and directly buried optical telecommunication cables (IEC 60794-3-10:2002, modified) / Note: Endorsement notice
|
| EN 637-1994
| 塑料管道系統 玻璃增強塑料部件 用重量分析法測定成分含量
| Plastics piping systems - Glass-reinforced plastics components - Determination of the amounts of constituents using the gravimetric method
|
| EN 681-1-1996+A1-1998 +A2-2002+AC-2002
| 彈性密封件 供水和排水管道用管聯接密封件的材料要求 第1部分：琉化橡膠
| Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
|
| EN 681-2-2000+A1-2002
| 彈性密封件 供水和排水管道用管聯接密封件的材料要求 第2部分：熱塑性合成橡膠
| Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
|
| EN 681-3-2000+A1-2002
| 彈性密封件 供水和排水管道用管聯接密封件的材料要求 第3部分：硫化橡膠的泡沫材料
| Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber
|
| EN 681-4-2000+A1-2002
| 彈性密封件 供水和排水管道用管聯接密封件的材料要求 第4部分：澆鑄聚氨酯密封元件
| Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements
|
| EN 682-2002
| 彈性密封件 用于運送氣體和碳?xì)浠衔镆后w的管道和配件的密封件的材料要求
| Elastomeric seals - Materials requirements for seals used in pipes and fittings carrying gas and hydrocarbon fluids
|
| EN 705-1994
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管和配件 回歸分析及其使用方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analysis and their use
|
| EN 712-1993
| 熱塑管道系統 壓力管和配件間承受機械接合件的端部負載 在恒定徑向力下抗拔出性能的試驗方法
| Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force
|
| EN 713-1993
| 塑料管道系統 配件和聚烯烴壓力管間的機械接合件 彎曲時組件內部壓力密封性的試驗方法
| Plastic piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending
|
| EN 714-1994
| 熱塑管道系統 壓力管和模塑配件間的無端部負載的彈性密封環型接合件 在無軸向推力時內部流體靜力學壓力下
| Thermoplastics piping systems - Non-end-load-bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings - Test method for leaktightness under internal hydrostatic pressure without end thrust
|
| EN 715-1994
| 熱塑管道系統 小直徑壓力管和配件間端部負荷的接合件 在包含軸向推力的內部水壓下密封性的試驗方法
| Thermoplastics piping systems - End-load bearing joints between small diameter pressure pipes and fittings-Test method for leaktightness under internal water pressure, including end thrust
|
| EN 727-1994
| 塑料管道和導管系統 熱塑性管和配件 維卡（Vicat）軟化溫度（VST）的測定
| Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST)
|
| EN 728-1997
| 塑料管道和導管系統 聚烯烴管和配件 氧化感應時間的測定
| Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
|
| EN 737-1-1998
| 醫療氣體管道系統 第1部分：壓縮醫療氣體和真空用終端設備
| Medical gas pipeline systems - Part 1: Terminal units for compressed medical gases and vacuum
|
| EN 737-2-1998+A1 -1999+AC-2000
| 醫療氣體管道系統 第2部分：麻醉氣體凈化處理系統 基本要求
| Medical gas pipeline systems - Part 2: Anaesthetic gas scavenging disposal systems - Basic requirements
|
| EN 737-3-1998+A1 -1999+AC-2000
| 醫療氣體管道系統 第3部分：壓縮醫療氣體和真空用管道
| Medical gas pipeline systems - Part 3: Pipelines for compressed medical gases and vacuum
|
| EN 737-4-1998
| 醫療氣體管道系統 第4部分：麻醉氣體凈化系統的終端設備
| Medical gas pipeline systems - Part 4: Terminal units for anaesthetic gas scavenging systems
|
| EN 743-1994
| 塑料管道和導管系統 熱塑管 縱向復原的測定
| Plastic piping and ducting systems -Thermoplastics pipes -Determination of the longitudinal reversion
|
| EN 744-1995
| 塑料管道和導管系統 熱塑管 連續法耐外部吹風的試驗方法
| Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method
|
| EN 761-1994
| 塑料管道系統 玻璃增強熱固性塑料管 干燥條件蠕變系數的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under dry conditions
|
| EN 763-1994
| 塑料管道和導管系統 噴射鑄模熱塑型配件 外觀檢查加熱效果的試驗方法
| Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Test method for visually assessing effects of heating
|
| EN 802-1994
| 塑料管道和導管系統 壓力管道系統的噴射鑄造熱塑性部件 擠壓最大變形試驗方法
| Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing
|
| EN 803-1994
| 塑料管道系統 壓力管道的彈性密封環狀連接的噴射鑄造熱塑性部件 無軸向推力的瞬時內壓阻力試驗方法
| Plastics piping systems - Injection-moulded thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test method for resistance to a short-term internal pressure without end thrust
|
| EN 804-1994
| 塑料管道系統 壓力管道溶焊接頭的噴射鑄造插接部件 瞬時內部液壓阻力的試驗方法
| Plastics piping systems - Injection-moulded socket fittings for solvent-cemented joints for pressure piping - Test method for resistance to a short-term internal hydrostatic pressure
|
| EN 911-1995
| 塑料管道系統 熱塑塑料壓力管道用的彈性密封環型接頭和機械接頭 外部液壓條件下防漏密封試驗方法
| Plastics piping systems - Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - Test method for leaktightness under external hydrostatic pressure
|
| EN 921-1994+AC-1995
| 塑料管道系統 熱塑管 恒定溫度下耐內壓的測定
| Plastics piping systems - Thermoplastics pipes - Determination of resistance to internal pressure at constant temperature / Note: To be replaced by prEN ISO 1167-1 (2003-04), prEN ISO 1167-2 (2003-04).
|
| EN 922-1994
| 塑料管和管道系統 未增塑聚氯乙烯管道和配件 粘度值測定和K值計算的樣品準備
| Plastics piping and ducting systems - Pipes and fittings of unplasticized poly(vinyl chloride) (PVC-U) - Specimen preparation for determination of the viscosity number and calculation of the K-value
|
| EN 969-1995+A1-1998
| 煤氣管道用球墨鑄鐵管、配件、附件及其接頭 要求和試驗方法
| Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods
|
| EN ISO 10380-2003
| 管道系統 波紋金屬軟管和軟管組件
| Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2003)
|
| EN ISO 10472-3-1997
| 工業洗衣機安全要求 第3部分：管道式洗滌(聯合)機及相關機械
| Safety requirements for industrial laundry machinery - Part 3: Washing tunnel lines including component machines (ISO 10472-3:1997)
|
| EN ISO 10807-1996
| 管道工程 在爆燃性空氣中電纜保護用皺紋軟金屬管組件
| Pipework - Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmosphere (ISO 10807:1994)
|
| EN ISO 11691-1995
| 聲學 無氣流管道消聲器插入損失的測量 實驗室測量法
| Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995)
|
| EN ISO 13703-2000
| 石油和天然氣工業 海上開采平臺上管道系統的設計和安裝
| Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO 13703:2000)
|
| EN ISO 13783-1997
| 塑料管道系統 硬聚氯乙烯(PVC-U)端部承受負荷的雙承口連接件 密封和承受彎曲及內壓的試驗方法
| Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure (ISO 13783:1997)
|
| EN ISO 13844-2000
| 塑料管道系統 用于硬(聚氯乙烯)(PVC-U) 管道的彈性密封環式承口連接件 負壓下密封試驗方法
| Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure (ISO 13844:2000)
|
| EN ISO 13845-2000
| 塑料管道系統 用于硬(聚氯乙烯)(PVC-U) 管道的彈性密封環式承口連接件 內壓下角度偏轉密封試驗方法
| Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection (ISO 13845:2000)
|
| EN ISO 13846-2000
| 塑料管道系統 熱塑性加壓塑料管道用端部負載軸承和非端部負載軸承的安裝和連接 在內水壓下長期密封的試驗
| Plastics piping systems - End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaktightness under internal water pressure (ISO 13846:2000)
|
| EN ISO 14723-2001
| 石油和天然氣工業 管道輸送系統 海底管道閥
| Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2001)
|
| EN ISO 15493-2003
| 工業用塑料管道系統 丙烯腈丁二烯苯乙烯（ABS），未增塑聚氯乙烯（PVC-U）和氯化聚氯乙烯（PVC-C）米制部件
| Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specificatio
|
| EN ISO 15494-2003
| 工業用塑料管道系統 聚丁烯（PB），聚乙烯（PE）和聚丙烯（PP） 米制部件和系統規范
| Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the system; Metric series (ISO 15494:2003)
|
| EN ISO 15908-2002
| 熱塑塑料管道用膠粘劑 膠粘劑熱穩定性的測試方法
| Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesives (ISO 15908:2002)
|
| EN ISO 16871-2003
| 塑料管道和導管系統 塑料管道和配件 直接(自然)風化的方法
| Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering (ISO 16871:2003)
|
| EN ISO 5136-2003
| 聲學 風機或其他空氣移動裝置輻射入管道中的聲功率的測定 管道法
| Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method (ISO 5136:2003)
|
| EN ISO 5167-1-2003
| 用壓差裝置測量流體流量 第1部分：圓截面管道中插入的節流孔板、噴嘴和文杜利管
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003)
|
| EN ISO 5167-2-2003
| 圓截面管道中用壓差裝置測量流體流量 第2部分：銳孔法
| Measurement of fluid flow by means of pressure differential devices in circular cross-section conduits running full - Part 2: Orifice plates (ISO 5167-2:2003)
|
| EN ISO 5167-3-2003
| 圓截面管道中用壓差裝置測量流體流量 第3部分：噴嘴和文杜利噴嘴
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles (ISO 5167-3:2003)
|
| EN ISO 5167-4-2003
| 圓截面管道中用壓差裝置測量流體流量 第4部分：文杜利管
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4: Venturi tubes (ISO 5167-4:2003)
|
| EN ISO 6412-1-1994
| 技術制圖 管道的簡化表示法 第1部分：通則和正交表示法
| Technical drawings - Simplified representation of pipelines - Part 1: General rules and orthogonal representation (ISO 6412-1:1989)
|
| EN ISO 6412-2-1994
| 技術制圖 管道的簡化表示法 第2部分：等角投影
| Technical drawings - Simplified representation of pipelines - Part 2: Isometric projection (ISO 6412-2:1989)
|
| EN ISO 6412-3-1996
| 技術制圖 管道的簡化表示法 第3部分：通風和排放系統終端部件
| Technical drawings - Simplified representation of pipelines - Part 3: Terminal features of ventilation and drainage systems (ISO 6412-3:1993)
|
| EN ISO 6817-1995
| 封閉管道中導電液體流量的測量 采用電磁流率計的方法
| Measurement of conductive liquid flow in closed conduits - Method using electromagnetic flowmeters (ISO 6817:1992)
|
| EN ISO 7235-2003
| 聲學 管道消音器和氣端裝置的實驗室測量步驟 插入損失、流動噪聲和總壓損失
| Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss (ISO 7235:2003)
|
| EN ISO 7278-2-1995
| 液態烴 動態測量 計量校正系統 第2部分：管道校準
| Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters - Part 2: Pipe provers (ISO 7278-2:1988)
|
| EN ISO 8316-1995
| 封閉管道中液體流量的測定 采用在容積計量容器內收集液體的方法
| Measurement of liquid flow in closed conduits - Method by collection of the liquid in a volumetric tank (ISO 8316:1987)
|
| EN ISO 8795-2001
| 人類生活用水輸送用塑料管道系統 遷移評定 塑料管道遷移值的測定
| Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints (ISO 8795:2001)
|
| EN ISO 9080-2003
| 塑料管與管道系統 用推斷法測定熱塑管型材料長期流動液體靜力強度
| Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003)
|
| ENV 1046-2001
| 塑料管道和導管系統 運輸水或污水用建筑結構外系統 地上和地下安裝用規程
| Plastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for installation above and below ground
|
| ENV 12097-1997
| 建筑物通風 管道工程 對便于管道工程系統設施維護的管道工程部件的要求
| Ventilation for buildings - Ductwork - Requirements for ductwork components to facilitate maintenance of ductwork systems
|
| ENV 12108-2001
| 塑料管道系統 在建筑物內安裝家用冷熱壓力管道系統的指南
| Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
|
| ENV 1329-2-2001
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 硬塑聚氯乙烯(PVC-U) 第2部分：合格平定指南
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
|
| ENV 13801-2000
| 建筑物中用于糞便和污水排放（低溫和高溫）的塑料管道系統 熱塑性塑料 推薦的安裝規范
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation
|
| ENV 1401-2-2000
| 非壓力地下污廢水排放用塑料管道系統硬聚氯乙烯(PVC-U) 第2部分：合格評定
| Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for assessment of conformity
|
| ENV 1401-3-2001
| 非壓力地下污廢水排放用塑料管道系統 硬聚氯乙烯(PVC-U) 第3部分：安裝指南
| Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation
|
| ENV 1451-2-2001
| 建筑物結構內污物和污水排出(低和高溫)用塑料管道系統 聚丙烯(PP ) 第2部分：合格評定指南
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
|
| ENV 1452-6-2001
| 供水塑料管道系統 硬塑聚氯乙烯(PVC-U) 第6部分：安裝指南
| Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Guidance for installation
|
| ENV 1452-7-2000
| 供水塑料管道系統 硬聚氯乙烯(PVC-U) 第7部分：合格評定指南
| Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 7: Guidance for the assessment of conformity
|
| ENV 1453-2-2000
| 建筑物內污物和廢水排放(低和高溫)帶結構壁管道的塑料管道系統 硬聚氯乙烯(PVC-U) 第2部分：合格評定指南
| Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
|
| ENV 1455-2-2001
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 丙烯腈 丁二烯 苯乙烯共聚物 第2部分：合格證評
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Guidance for the assessment of conformity
|
| ENV 1519-2-2001
| 建筑物結構內污物和污水排放(低和高溫)塑料管道系統 聚已烯(PE) 第2部分：合格評定指南
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity
|
| ENV 1565-2-2001
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 苯乙烯共聚混合物(SAN+PVC) 第2部分：合格評定指南
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 2: Guidance for the assessment of conformity
|
| ENV 1566-2-2001
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 氯化聚偏氯乙烯(PVC-C) 第2部分：合格評定指南
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly (vinyl chloride) (PVC-C) - Part 2: Guidance for the assessment of conformity
|
| ENV 1852-2-2000
| 無壓地下排水和污水用塑料管道系統 聚丙烯(PP) 第2部分：合格評定指南
| Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
|
| ENV 1993-4-1-1999
| 歐洲法典 3：鋼結構設計 第4-1部分：豎井、蓄水池和管道 豎井
| Eurocode 3: Design of steel structures - Part 4-1: Silos, tanks and pipelines - Silos
|
| ENV 1993-4-2-1999
| 歐洲法典 3：鋼結構設計 第4-2部分：豎井、蓄水池和管道 蓄水池
| Eurocode 3: Design of steel structures - Part 4-2: Silos, tanks and pipelines - Tanks
|
| ENV 1993-4-3-1999
| 歐洲法典 3：鋼結構設計 第4-3部分：豎井、蓄水池和管道 管道
| Eurocode 3: Design of steel structures - Part 4-3: Silos, tanks and pipelines - Pipelines
|
| ENV 1998-4-1998
| 歐洲法典8：結構抗震的設計規定 第4部分：豎井 蓄水池和管道
| Eurocode 8: Design provisions for earthquake resistance of structures - Part 4: Silos, tanks and pipelines
|
| ENV 737-6-2003
| 醫療氣體管道系統 第6部分：壓縮醫療氣體和真空用終端部件用探針的尺寸
| Medical gas pipeline systems - Part 6: Dimensions and allocation of probes for terminal units for compressed medical gases and vacuum
|
| ENV 852-2001
| 運輸人類用水的塑料管道系統 移動評估 源自移動值的實驗室說明指南
| Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Guidance on the interpretation of laboratory derived migration values
|
| prEN 1016-1993
| 塑料管道系統 非可塑聚氯乙烯一端受載的雙孔接頭 彎曲和內部壓力時的密封性和強度試驗方法
| Plastics piping systems; unplasticized poly(vinyl chloride) (PVC-U) end-load bearing double socket joints; test method for leaktightness and strength while subjected to bending and internal pressure
|
| prEN 10208-3-1997
| 易燃流體管道用鋼管 交貨技術條件 第3部分：符合C類要求的管材
| Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 3: Pipes of requirement class C
|
| prEN 1042-1995
| 塑料管道系統 聚烯烴管和/或配件間的熔接連接件 恒溫下內部壓力抵抗力的測定
| Plastics piping systems - Fusion joints between polyolefin pipes and/or fittings - Determination of resistance to internal pressure at constant temperature
|
| prEN 1115-2-1997
| 壓力下地下排水和排污裝置用塑料管道系統 基于非飽和聚酯樹脂的玻璃增強熱固性塑料（GRP） 第2部分：具撓
| Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints
|
| prEN 1115-4-1993
| 壓力下地下排水和排污裝置用塑料管道系統 基于聚脂樹脂的玻璃增強熱固性塑料（GRP） 第4部分：輔助設備
| Plastics piping systems for underground drainage and sewerage under pressure; glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP); part 4 (informative): ancillary equipment
|
| prEN 1115-6-1997
| 壓力下地下排水和排污裝置用塑料管道系統 基于非飽和聚酯樹脂的玻璃增強熱固性塑料（GRP） 第6部分：安裝
| Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 6: Practices for installation
|
| prEN 1115-7-1995
| 壓力下地下排水和排污裝置用塑料管道系統 基于非飽和聚酯樹脂的玻璃增強熱固性塑料（GRP） 第7部分：一致
| Plastics piping systems for underground drainage and sewerage under pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 7: Assessment of conformity
|
| prEN 12666-1-2001
| 非壓力地下排水和排污用塑料管道系統 聚乙烯（PE）.第1部分：管道、配件和系統規范
| Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
|
| prEN 1329-3-1998
| 建筑物結構內污物和廢水排放（低和高溫）用塑料管道系統 硬塑聚氯乙烯（PVCU) 第3部分：安裝指南
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation
|
| prEN 1329-5-1994
| 建筑物結構內污物和廢水排放（低和高溫）用塑料管道系統 硬塑聚氯乙烯（PVCU) 第5部分：對系統用途的適宜
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 5: fitness for purpose of the system
|
| prEN 1329-6-1994
| 建筑物結構內污物和廢水排放（低和高溫）用塑料管道系統 硬塑聚氯乙烯（PVC-U）.第6部分：推薦的安裝實踐
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Recommended practice for installation
|
| prEN 1336-1993
| 塑料管道系統 熱塑性壓力管道用終端承載和無承開組件和接頭 內部水壓力下長期密封性試驗方法
| Plastics piping systems; end-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping; test method for long-term leaktightness under internal water pressure
|
| prEN 13476-1-2002
| 非壓力地下排水和污水熱塑性塑料管道系統 聚氯乙烯（PVC-U）、聚丙烯（PP）)和聚已烯（PE）的結構墻管道系
| Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for pipes, fittings and the syste
|
| prEN 13480-6-2002
| 工業用金屬管道 第6部分：地下管道的附加要求
| Metallic industrial piping - Part 6: Additional requirements for buried piping
|
| prEN 13566-2-2002
| 用于修復非壓力排水和污水網的塑料管道系統 第2部分：帶連續管的襯套
| Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes
|
| prEN 13636-2003
| 掩埋金屬罐和相關管道的陰極保護
| Cathodic protection of buried metallic tanks and related piping
|
| prEN 1401-5-1994
| 非壓力地下污廢水排放用塑料管道系統 硬聚氯乙烯(PVC-U) 第5部分：使用系統的適合性
| Plastics piping systems for non-pressure underground drainage and sewerage; unplasticized poly(vinyl chloride) (PVC-U); part 5: fitness for purpose of the system
|
| prEN 14125-2003
| 汽油加油站的地下管道工程
| Pipework for underground installation at petrol stations
|
| prEN 14141-2003
| 天然氣管道輸送閥 試驗和性能要求
| Valves for natural gas transportation in pipelines - Performance requirements and tests
|
| prEN 14161-2003
| 石油和天然氣工業 管道運輸系統
| Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2000 modified)
|
| prEN 14239-2003
| 建筑物通風 管道系統 管道系統 表面積測量
| Ventilation for buildings - Ductwork - Measurement of ductwork surface area
|
| prEN 14280-2001
| 地下電纜管道的塑料管線系統 未增塑聚氯乙烯 塑料管、管件及管線規范
| Plastics piping systems for buried cable ducting - Unplasticized poly(vinyl chloride) (PVC-U) - Specifications for pipes, fittings and the system
|
| prEN 14281-2001
| 地下電纜管道的塑料管線系統 聚乙烯 塑料管、管件及管線規范
| Plastics piping systems for buried cable ducting - Polyethylene (PE) - Specifications for pipes, fittings and the system
|
| prEN 14282-2001
| 地下電纜管道的塑料管線系統 聚丙烯 塑料管、管件及管線規范
| Plastics piping systems for buried cable ducting - Polypropylene (PP) - Specifications for pipes, fittings and the system
|
| prEN 14283-2001
| 一般用途地下管道的塑料管線系統 未增塑聚氯乙烯 塑料管、管件及管線規范
| Plastics piping systems for general purpose buried ducting - Unplasticized poly(vinyl chloride) (PVC-U) - Specifications for pipes, fittings and the system
|
| prEN 14284-2001
| 一般用途地下管道的塑料管線系統 聚乙烯 塑料管、管件及管線規范
| Plastics piping systems for general purpose buried ducting - Polyethylene (PE) - Specifications for pipes, fittings and the system
|
| prEN 14285-2001
| 一般用途地下管道的塑料管線系統 聚丙烯 塑料管、管件及管線規范
| Plastics piping systems for general purpose buried ducting - Polypropylene (PP) - Specifications for pipes, fittings and the system
|
| prEN 1445-2000
| 纖維水泥管道 現場壓力試驗
| Fibre-cement pipelines - Field pressure testing
|
| prEN 1451-3-1994
| 建筑物結構內用于污物和污水排放（高/低溫）的塑料管道系統 聚丙烯（PP） 第3部分：管件
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 3: Fittings
|
| prEN 1451-5-1994
| 建筑物結構內用污物和污水排放（高/低溫）的塑料管道系統 聚丙烯（PP） 第5部分：系統用途的適合性
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 5: Fitness for purpose of the system
|
| prEN 1451-6-1994
| 建筑物結構內用于污物和污水排放（高/低溫）的塑料管道系統 聚丙烯（PP) 第6部分：推薦的安裝實踐
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building - Polypropylene (PP) - Part 6: Recommended practice for installation
|
| prEN 1453-3-1998
| 建筑物內污物和廢水排放(低和高溫)帶結構壁管道的塑料管道系統 硬聚氯乙烯(PVC-U) 第3部分：安裝指南
| Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Guidance for installation
|
| prEN 1453-5-1994
| 建筑物內污物和廢水排放(低和高溫)帶結構壁管道的塑料管道系統 硬聚氯乙烯(PVC-U) 第5部分：系統用管件
| Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 5: fittings for purpose of the system
|
| prEN 1453-6-1994
| 建筑物內污物和廢水排放(低和高溫)帶結構壁管道的塑料管道系統 硬聚氯乙烯(PVC-U) 第6部分：推薦安裝實踐
| Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) within the building structure; unplasticized poly(vinyl chloride) (PVC-U); part 6: recommended practice for installation
|
| prEN 1455-3-1994
| 建筑物結構內用于污物和污水排放（高/低溫）的塑料管道系統 丙烯晴 丁二烯 苯已烯共聚物(ABS) 第3部分
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 3: Fittings
|
| prEN 1455-6-1994
| 建筑物結構內用于污物和污水排放（高/低溫）的塑料管道系統 丙烯晴 丁二烯 苯已烯共聚物(ABS) 第6部分
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building - Acrylonitrile-butadiene-styrene (ABS) - Part 6: Recommended practice for installation
|
| prEN 1456-3-1994
| 地上和地下污廢水壓力排放用塑料管道系統 硬已烯(聚氯已烯)(PVC-U) .第3部分：管件
| Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings
|
| prEN 1456-4-1994
| 地上和地下污廢水壓力排放用塑料管道系統 硬已烯(聚氯已烯)(PVC-U) 第4部分：閥門及輔助設備
| Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves and ancillary equipment
|
| prEN 1456-5-1994
| 地上和地下污廢水壓力排放用塑料管道系統 硬已烯(聚氯已烯)(PVC-U) 第5部分：對系統用途的適宜性
| Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 5: Fitness for purpose of the system
|
| prEN 1456-6-1994
| 地上和地下污廢水壓力排放用塑料管道系統 硬已烯(聚氯已烯)(PVC-U) 第6部分：推薦的安裝實踐
| Plastics piping systems for underground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Recommended practice for installation
|
| prEN 1507-2002
| 建筑物通風 管道系統 矩形金屬片通風管道 強度和泄露 要求和試驗
| Ventilation for buildings - Sheet metal air ducts with rectangular section - Requirements for strength and leakage
|
| prEN 1519-3-1994
| 建筑物結構內污物和污水排放(低和高溫)塑料管道系統 聚已烯(PE) 第3部分：管件
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 3: Fittings
|
| prEN 1519-5-1994
| 建筑物結構內污物和污水排放(低和高溫)塑料管道系統.聚已烯(PE) 第5部分：針對系統用途的適合性
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
|
| prEN 1519-6-1995
| 建筑物結構內污物和污水排放(低和高溫)塑料管道系統 聚已烯(PE) 第6部分：推薦的安裝實踐
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 6: Recommanded practice for installation
|
| prEN 1555-6-1995
| 供給氣體燃料用塑料管道系統 聚已烯(PE) 第6部分：推薦的安裝實踐
| Plastics piping systems for gaseous fuels supply - Polyethylene (PE) - Part 6: Recommended practice for installation
|
| prEN 1565-3-1994
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 苯乙烯共聚混合物(SAN+PVC) 第3部分：管件
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 3: Fittings
|
| prEN 1565-5-1994
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 苯乙烯共聚混合物(SAN+PVC) 第5部分：針對系統用途
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 5: Fitness for purpose of the system
|
| prEN 1565-6-1995
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 苯乙烯共聚混合物(SAN+PVC) 第6部分：推薦的安裝實
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN + PVC) - Part 6: Recommended practice for installation
|
| prEN 1566-3-1994
| 建筑物結構內污物和廢水排放(低和高溫)用塑料管道系統 氯化聚偏氯乙烯(PVC-C) 第3部分：管件
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings
|
| prEN 1566-5-1994
| 建筑物結構內污物和污水排放(低和高溫)用塑料管道系統 氯化已烯(聚氯已烯)(PVC-C) 第5部分：針對系統用途
| Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system
|
| prEN 1636-1-1996
| 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第1部分：總則
| Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 1: General
|
| prEN 1636-2-1996
| 無壓力排水道和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第2部分：帶有撓
| Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints
|
| prEN 1636-4-1994
| 無壓力排水和污水用塑料管道系統 不飽和聚脂樹脂(UP) 基玻璃纖維增強熱固性塑料(GRP) 第4部分：輔助設備
| Plastics piping systems for non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment
|
| prEN 1763-2-2000
| 供氣相丙烷和丁烷使用的撓性軟管、管道及組裝件 第2部分：對管咀接頭及組裝件的要求
| Flexible hose, tubing and assemblies for use with propane and butane in the vapour phase - Part 2: Requirements for nozzles, couplings and assemblies
|
| prEN 1796-2-1995
| 有或無壓力供水用塑料管道系統 非飽和性聚脂樹脂基玻璃增強熱固性塑料 第2部分：帶撓性、縮口活節或剛性
| Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 2: Pipes with flexible, reduced articulation or rigid joints
|
| prEN 1796-2003
| 有或無壓力供水用塑料管道系統 非飽和性聚脂樹脂基玻璃增強熱固性塑料
| Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
|
| prEN 1796-3-1995
| 有或無壓力供水用塑料管道系統聚合物樹脂（UP）基玻璃纖維增強熱固性塑料（GRP） 第3部分：管件
| Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 3: Fittings
|
| prEN 1796-4-1995
| 有或無壓力供水有塑料管道系統聚合物樹脂（UP）基玻璃纖維增強熱固性塑料（GRP） 第4部分：輔助設備
| Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 4: Ancillary equipment
|
| prEN 1796-5-1995
| 有或無壓力供水用塑料管道系統聚合物樹脂（UP）基玻璃纖維增強熱固性塑料（GRP） 第5部分：系統用途的適合
| Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 5: Fitness for the purpose of the system
|
| prEN 1796-6-1995
| 有或無壓力供水用塑料管道系統聚合物樹脂（UP）基玻璃纖維增強熱固性塑料（GRP） 第6部分：推薦的安裝實踐
| Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) - Part 6: Recommended practice for installation
|
| prEN 1852-5-1995
| 無壓地下排水和污水用塑料管道系統 聚炳烯(PP) 第5部分：對系統配合的適宜性
| Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 5: Fitness for purpose of the system
|
| prEN 45512-1994
| 采購指南 管道系統和閥 包括安全閥的鍋爐和高壓管道閥
| Guide for procurement - Pipework and valves - Boiler and high pressure piping valves including safety valves
|
| prEN 45513-1994
| 采購指南 管道系統和閥 包括支架的高壓管線
| Guide for procurement - Pipework and valves - High pressure piping including supports
|
| prEN 474-9-2001
| 土方機械 安全 第9部分：管道敷設機的要求
| Earth-moving machinery - Safety - Part 9: Requirements for pipelayers
|
| prEN 50085-2-1-2002
| 電氣裝置用電纜槽和電纜管道系統 第2-1部分：安裝在墻上或天花板上的電纜槽和電纜管道系統的特殊要求
| Cable trunking and cable ducting systems for electrical installations - Part 2-1: Particular requirements for cable trunking systems and cable ducting systems intended for mounting on walls and/or ceilings
|
| prEN 762-1995
| 塑料管道和導管系統 熱塑系統用彈性密封接頭 密封環保持力和損壞的試驗方法
| Plastics piping and ducting systems - Joints with elastomeric seals for thermoplastic systems - Test method for retention of, and damage to, sealing rings
|
| prEN 806-3-2003
| 建筑物內人類用水輸送裝置規范 第3部分：管道尺寸
| Specifications for installations inside buildings conveying water for human consumption - Part 3: Pipe sizing
|
| prEN 987-1995
| 塑料管道和導管系統 鑄模裝置 裝置中磨掉碎片擺錘式?jīng)_擊試驗強度的測定
| Plastics piping and ducting systems - Injection-moulded fittings - Determination of the Charpy impact strength of test pieces cut from a fitting
|
| prEN ISO 10806-2003
| 管道工程 皺紋軟金屬管用非合金及不銹鋼配件
| Pipework - Fittings for corrugated metallic hoses (ISO/FDIS 10806:2003)
|
| prEN ISO 14828-1999
| 塑料管道系統 玻璃纖維增強熱固塑料管 在濕環境下長期特殊環形松弛勁度的測定和濕松弛系數的計算
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor (ISO/DIS 14828:1999)
|
| prEN ISO 15002-1996
| 醫用氣體管道系統終端裝置用氣流量測量裝置
| Flow-metering devices for connection to terminal units of medical gas pipeline systems (ISO/DIS 15002:1996)
|
| prEN ISO 15465-2002
| 管道工程 條繞金屬軟管和軟管組件
| Pipework - Stripwound metal hoses and hose assemblies (ISO/DIS 15465:2002)
|
| prEN ISO 15749-2-2001
| 船舶和造船技術 船和海上構筑物上排水系統 第2部分：生活污水排水、排水管道的自流系統
| Ships and marine technology - Drainage systems on ships and marine structures - Part 2: Sanitary drainage, drain piping for gravity system (ISO/DIS 15749-2:2001)
|
| prEN ISO 15749-4-2001
| 船舶和造船技術 船和海上構筑物上排水系統 第4部分：生活污水排水、污物處理排出管道
| Ships and marine technology - Drainage systems on ships and marine structures - Part 4: Sanitary drainage, sewage disposal pipes (ISO/DIS 15749-4:2001)
|
| prEN ISO 15874-1-2002
| 冷熱水用塑料管道系統 聚乙烯（PE） 第1部分：總則
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General (ISO/FDIS 15874-1:2002)
|
| prEN ISO 15874-2-2002
| 冷熱水用塑料管道系統 聚丙烯（PP） 第2部分：管道
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO/FDIS 15874-2:2002)
|
| prEN ISO 15874-3-2002
| 冷熱水用塑料管道系統 聚丙烯（PP） 第3部分：配件
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings (ISO/FDIS 15874-3:2002)
|
| prEN ISO 15874-5-2002
| 冷熱水用塑料管道系統 聚丙烯（PP） 第5部分：系統目的的適配性
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO/FDIS 15874-5:2002)
|
| prEN ISO 15875-1-2002
| 冷熱水塑料管道系統 交聯聚乙稀（ PE - X ） 第1部分：總則
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General (ISO/FDIS 15875-1:2002)
|
| prEN ISO 15875-2-2002
| 冷熱水塑料管道系統 交聯聚乙稀（ PE - X ） 第2部分：管道
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes (ISO/FDIS 15875-2:2002)
|
| prEN ISO 15875-3-2002
| 冷熱水塑料管道系統 交聯聚乙稀（ PE - X ） 第3部分：接頭
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO/FDIS 15875-3:2002)
|
| prEN ISO 15875-5-2002
| 冷熱水塑料管道系統 交聯聚乙稀（ PE - X ） 第5部分：系統適用性
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO/FDIS 15875-5:2002)
|
| prEN ISO 15876-1-2002
| 冷熱水塑料管道系統 聚丁稀（ PB ） 第1部分：總則
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General (ISO/FDIS 15876-1:2002)
|
| prEN ISO 15876-2-2002
| 冷熱水塑料管道系統 聚丁稀（ PB ） 第2部分：管道
| Plastics piping systems for hot and cold water installations - Polybutylen (PB) - Part 2: Pipes (ISO/FDIS 15876-2:2002)
|
| prEN ISO 15876-3-2002
| 冷熱水塑料管道系統 聚丁稀（ PB ） 第3部分：接頭
| Plastics piping systems for hot and cold water installations - Polybutylen (PB) - Part 3: Fittings (ISO/FDIS 15876-3:2002)
|
| prEN ISO 15876-5-2002
| 冷熱水塑料管道系統 聚丁稀（ PB ） 第5部分：系統適用性
| Plastics piping systems for hot and cold water installations - Polybutylen (PB) - Part 5: Fittness for purpose of the system (ISO/FDIS 15876-5:2002)
|
| prEN ISO 15877-1-2002
| 冷熱水用塑料管道系統 氯化聚氯乙烯（PVC-C）第1部分：總則
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General (ISO/FDIS 15877-1:2002)
|
| prEN ISO 15877-2-2002
| 冷熱水用塑料管道系統 氯化聚氯乙烯（PVC-C）第2部分：管道
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes (ISO/FDIS 15877-2:2002)
|
| prEN ISO 15877-3-2002
| 冷熱水用塑料管道系統 氯化聚氯乙烯（PVC-C）第3部分：接頭
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings (ISO/FDIS 15877-3:2002)
|
| prEN ISO 15877-5-2002
| 冷熱水用塑料管道系統 氯化聚氯乙烯（PVC-C）第5部分：系統用途的適合性
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system (ISO/FDIS 15877-5:2002)
|
| prEN ISO 580-2002
| 塑料管與管道系統 注模制熱塑性塑料配件 加熱反應的視覺評估方法
| Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO/DIS 580:2002)
|
| prEN ISO 7369-2002
| 管道工程 金屬軟管和軟管裝備 詞匯
| Pipework - Metal hoses and hose assemblies - Vocabulary (ISO/DIS 7369:2002)
|
| 編號 | 中文名稱 | 英文名稱 |
|---|