| 編號 | 中文名稱 | 英文名稱 |
|---|
| IEC 60794-3-10-2002
| 光學纖維電纜.第3-10部分:戶外電纜.管道光纜和直埋通信光纜的系列規范
| Optical fibre cables - Part 3-10: Outdoor cables; Family specification for duct and directly buried optical telecommunication cables
|
| IEC 60794-3-12-2005
| 光纜.第3-12部分:室外電纜.房屋布線用管道和直埋通信光纜的詳細規范
| Optical fibre cables - Part 3-12: Outdoor cables - Detailed specification for duct and directly buried optical telecommunication cables for use in premises cabling
|
| IEC 61084-1 AMD 1-1993
| 電氣裝置用電纜槽和管道系統 第1部分:一般要求 修改1
| Cable trunking and ducting systems for electrical installations; part 1: general requirements; amendment 1
|
| IEC 61084-1-1991
| 電氣裝置用電纜槽和管道系統 第1部分:一般要求
| Cable trunking and ducting systems for electrical installations; part 1: general requirements
|
| IEC 61084-2-1-1996
| 電氣裝置用電纜槽和管道系統 第2部分:特殊要求 第1節:安裝在墻上或天花板上的電纜槽和管道系統
| Cable trunking and ducting systems for electrical installations - Part 2: Particular requirements - Section 1: Cable trunking and ducting systems intended for mounting on walls or ceilings
|
| IEC 61084-2-2-2003
| 電氣裝置用電纜槽和管道系統.第2-2部分:特殊要求.安裝在地板下和與地板齊平的設施用電纜槽和管道系統
| Cable trunking and ducting systems for electrical installations - Part 2-2: Particular requirements; Cable trunking systems and cable ducting systems intended for underfloor and flushfloor installations
|
| IEC 61084-2-4-1996
| 電氣裝置用電纜槽和管道系統 第2部分:特殊要求 第4節:接線柱
| Cable trunking and ducting systems for electrical installations - Part 2: Particular requirements - Section 4: Service poles
|
| IEC 61400-21-2001
| 風輪發電機系統 第21部分：管道連接風輪機功率質量特性的測量和評定
| Wind turbine generator systems - Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines
|
| ISO 10380-2003
| 管道系統.波紋狀金屬軟管和軟管配件
| Pipework - Corrugated metal hoses and hose assemblies
|
| ISO 10466-1997
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管材 耐初始環狀變形可能性試驗方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection
|
| ISO 10467-2004
| 壓力和無壓力排水和排污塑料管道系統.基于不飽和聚酯樹脂的玻璃增強熱固性塑料(GRP)系統
| Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
|
| ISO 10472-3-1997
| 工業洗衣機安全要求 第3部分:管道式洗滌(聯合)機及相關機械
| Safety requirements for industrial laundry machinery - Part 3: Washing tunnel lines including component machines
|
| ISO 10508-2006
| 冷熱水裝置用塑料管道系統.分類和設計指南
| Plastics piping systems for hot and cold water installations - Guidance for classification and design
|
| ISO 10639-2004
| 壓力和無壓力給水塑料管道系統.基于不飽和聚酯樹脂的玻璃增強熱固性塑料(GRP)系統
| Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
|
| ISO 10790-1999
| 封閉管道中流體流量的測量 科里奧利計選擇、安裝和使用指南(流量、密度和容量的測定)
| Measurement of fluid flow in closed conduits - Guidance to the selection, installation and use of Coriolis meters (mass flow, density and volume flow measurements)
|
| ISO 10802-1992
| 球墨鑄鐵管道 安裝后水壓試驗
| Ductile iron pipelines; hydrostatic testing after installation
|
| ISO 10804-1-1996
| 球墨鑄鐵管道用減震連接系統 第1部分:設計規則和定型試驗
| Restrained joint systems for ductile iron pipelines - Part 1: Design rules and type testing
|
| ISO 10806-2003
| 管道工程.波紋狀金屬軟管用配件
| Pipework - Fittings for corrugated metal hoses
|
| ISO 10807-1994
| 管道工程 在爆燃性空氣中電纜保護用皺紋軟金屬管組件
| Pipework - Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmospheres
|
| ISO 10838-1-2000
| 燃?xì)庥镁垡蚁┕艿老到y(tǒng)的機械式管件 第1部分:公稱外徑小于或等于63mm的管道用金屬管件
| Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
|
| ISO 10838-2-2000
| 燃?xì)庥镁垡蚁┕艿老到y(tǒng)的機械式管件 第2部分:公稱外徑大于63mm的管道用金屬管件
| Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
|
| ISO 10838-3-2001
| 燃?xì)庥镁垡蚁┕艿老到y(tǒng)的機械管件 第3部分：標稱外徑小于或等于63mm的熱塑管件
| Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels - Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
|
| ISO 10928-1997
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管材和管件 回歸分析及其使用方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analysis and their use
|
| ISO 10931-2005
| 工業用塑料管道系統.聚偏氟乙烯(PVDF).部件和系統的規范
| Plastics piping systems for industrial applications - Poly(vinylidene fluoride) (PVDF) - Specifications for components and the system
|
| ISO 10952-1999
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管材和管件 在變形條件下斷面內部耐化學腐蝕性的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack from the inside of a section in a deflected condition
|
| ISO 11563-2003
| 原油和石油制品.散貨運輸.實現管道滿度的指南
| Crude petroleum and petroleum products - Bulk cargo transfer - Guidelines for achieving the fullness of pipelines
|
| ISO 11691-1995
| 聲學 無氣流管道消聲器插入損失的測量 實驗室測量法
| Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method
|
| ISO 13253-1995
| 管道式空調器和氣-氣加熱泵 性能的檢測和額定功率
| Ducted air-conditioners and air-to-air heat pumps - Testing and rating for performance
|
| ISO 13261-1-1998
| 空調和空氣源熱泵設備的聲功率額定值 第1部分:無室外管道設備
| Sound power rating of air-conditioning and air-source heat pump equipment - Part 1: Non-ducted outdoor equipment
|
| ISO 13261-2-1998
| 空調和空氣源熱泵設備的聲功率額定值 第2部分:無室內管道設備
| Sound power rating of air-conditioning and air-source heat pump equipment - Part 2: Non-ducted indoor equipment
|
| ISO 13359-1998
| 封閉管道中導電液體流量的測量 法蘭電磁流量計 總長
| Measurement of conductive liquid flow in closed conduits - Flanged electromagnetic flowmeters - Overall length
|
| ISO 13623-2000
| 石油和天然氣工業.管道輸送系統
| Petroleum and natural gas industries - Pipeline transportation systems
|
| ISO 13628-5-2002
| 石油和天然氣工業.水下采油系統的設計和操作.第5部分:水下纜線和管道
| Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals
|
| ISO 13678 Technical Corrigendum 1-2005
| 石油和天然氣工業.對套管、管道和管線用的螺紋油的評定和試驗.技術勘誤1
| Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing and line pipe; Technical Corrigendum 1
|
| ISO 13678-2000
| 石油和天然氣工業 對套管、管道和管線用的螺紋絕緣膏的評價和試驗
| Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing and line pipe
|
| ISO 13703 Technical Corrigendum 1-2002
| 石油和天然氣工業.近海生產平臺上管道系統的設計和安裝.技術勘誤1
| Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms; Technical Corrigendum 1
|
| ISO 13703-2000
| 石油和天然氣工業 海上開采平臺上管道系統的設計和安裝
| Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms
|
| ISO 13761-1996
| 塑料管材和管件 20℃以上使用的聚乙烯管道的壓力折減系數
| Plastics pipes and fittings - Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 C
|
| ISO 13783-1997
| 塑料管道系統 硬聚氯乙烯(PVC-U)端部承受負荷的雙承口連接件 密封和承受彎曲及內壓的試驗方法
| Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints - Test method for leaktightness and strength while subjected to bending and internal pressure
|
| ISO 13844-2000
| 塑料管道系統 用于硬聚氯乙烯管道的彈性密封環式承口連接件 負壓下密封試驗方法
| Plastics piping systems - Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes - Test method for leaktightness under negative pressure
|
| ISO 13845-2000
| 塑料管道系統 用于硬聚氯乙烯管道的彈性密封環式承口連接件 內壓下角度偏轉密封試驗方法
| Plastics piping systems - Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for leaktightness under internal pressure and with angular deflection
|
| ISO 13846-2000
| 塑料管道系統 熱塑性加壓塑料管道用端部負載軸承和非端部負載軸承的安裝和連接 在內水壓下長期密封的試驗方
| Plastics piping systems - End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping - Test method for long-term leaklightness under internal water pressure
|
| ISO 13847 Technical Corrigendum 1-2001
| 石油和天然氣工業.管道輸送系統.管道焊接.技術勘誤1
| Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines; Technical Corrigendum 1
|
| ISO 13847-2000
| 石油和天然氣工業 管道輸送系統 管道的焊接
| Petroleum and natural gas industrie - Pipeline transportation systems - Welding of pipelines
|
| ISO 13951-2001
| 塑料管道系統 聚烯烴管與管或管與管件之間的組件耐拉申負載試驗方法
| Plastics piping systems - Test method for the resistance of polyolefin pipe/pipe or pipe/fitting assemblies to tensile loading
|
| ISO 13968-1997
| 塑料管道及導管系統 熱塑性塑料管材 環揉性的測定
| Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility
|
| ISO 14164-1999
| 固定源排放 管道路氣體流速的測定 自動監測方法
| Stationary source emissions - Determination of the volume flowrate of gas streams in ducts - Automated method
|
| ISO 14313-1999
| 石油和天然氣工業 管道輸送系統 管道閥
| Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves
|
| ISO 14511-2001
| 封閉管道中流體流量的測量 熱質流量計
| Measurement of fluid flow in closed conduits - Thermal mass flowmeters
|
| ISO 14531-1-2002
| 塑料管道和配件.氣體燃料運輸用交聯聚乙烯管道系統.米制系列.第1部分:管
| Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels; Metric series; Specifications - Part 1: Pipes
|
| ISO 14531-2-2004
| 塑料管道和配件.氣體燃料運輸用交聯聚乙烯管道系統.米制系列.規范.第2部分:熱熔連接用配件
| Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 2: Fittings for heat-fusion jointing
|
| ISO 14531-3-2006
| 塑料管道和配件.氣體燃料運輸用交聯聚乙烯管道系統.米制系列.規范.第3部分:機械連接用配件(包括PE-X/金屬轉
| Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 3: Fittings for mechanical jointing (including PE-X/metal transitions)
|
| ISO 14531-4-2006
| 塑料管道和配件.氣體燃料運輸用交聯聚乙烯(PE-X)管道系統.米制系列.規范.第4部分:系統設計和安裝指南
| Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 4: System design and installation guidelines
|
| ISO 14692-3-2002
| 石油和天然氣工業.玻璃纖維增強塑料管.第3部分:系統管道
| Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System piping
|
| ISO 14723-2001
| 石油和天然氣工業 管道輸送系統 海底管道閥
| Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves
|
| ISO 14726-2-2002
| 船和造船技術.管道系統的內容的識別顏色.第2部分:中等差異和/或功能用補充顏色
| Ships and marine technology - Identification colours for the content of piping systems - Part 2: Additional colours for different media and/or functions
|
| ISO 15002-2000
| 醫用氣體管道系統終端裝置用氣流量測量裝置
| Flow-metering devices for connection to terminal units of medical gas pipeline systems
|
| ISO 15306-2003
| 玻璃增強熱固性塑料管道.抗周期性內壓力的測定
| Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the resistance to cyclic internal pressure
|
| ISO 15348-2002
| 管道工程.金屬波紋管膨脹節.總則
| Pipework - Metal bellows expansion joints - General
|
| ISO 15465-2004
| 管道.帶繞金屬軟管和軟管組件
| Pipework - Stripwound metal hoses and hose assemblies
|
| ISO 15493 Technical Corrigendum 1-2004
| 工業用塑料管道系統.丙烯腈-丁二烯-苯乙烯塑料(ABS)、未增塑的聚氯乙烯(PVC-U)和氯化聚氯乙烯(PVC-C).元件
| Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and the system - Metric series; Technical Corrigendum 1
|
| ISO 15493-2003
| 工業用塑料管道系統.丙烯腈-丁二烯-苯乙烯塑料(ABS)、未增塑的聚氯乙烯(PVC-U)和氯化聚氯乙烯(PVC-C).元件
| Plastics piping systems for industrial applications - Acrylonitrile-butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) - Specifications for components and piping systems; Metric series
|
| ISO 15494-2003
| 工業用塑料管道系統.聚丁烯(PE)聚乙烯(PE)聚丙烯(PP).元件和系統的規范.米制系列
| Plastics piping systems for industrial applications - Polybutene (PB), polyethylene (PE) and polypropylene (PP) - Specifications for components and the systems; Metric series
|
| ISO 15589-1-2003
| 石油和天然氣工業.管道運輸系統的陰極保護.第1部分:陸地管線
| Petroleum and natural gas industries - Cathodic protection of pipeline transportation systems - Part 1: On-land pipelines
|
| ISO 15589-2-2004
| 石油和天然氣工業.管道運輸系統的陰極保護.第2部分:海上管線
| Petroleum and natural gas industries - Cathodic protection of pipeline transportation systems - Part 2: Offshore pipelines
|
| ISO 15590-1-2001
| 石油和天然氣工業 管道輸送系統用誘導彎頭、管件和法蘭 第1部分：誘導彎頭
| Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends
|
| ISO 15590-2-2003
| 石油和天然氣工業.管道輸送系統用進氣彎管、管件和法蘭.第2部分:管件
| Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings
|
| ISO 15590-3-2004
| 石油和天然氣工業.管道輸送系統用進氣彎頭、管件和法蘭.第3部分:法蘭
| Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges
|
| ISO 15649-2001
| 石油和天然氣工業 管道
| Petroleum and natural gas industries - Piping
|
| ISO 15665 Technical Corrigendum 1-2004
| 聲學.管道、閥門和法蘭的隔音.技術勘誤1
| Acoustics - Acoustic insulation for pipes, valves and flanges; Technical Corrigendum 1
|
| ISO 15749-2-2004
| 船舶和海上技術.船舶和海上結構物的排水系統.第2部分:重力系統用衛生排水和排水管道
| Ships and marine technology - Drainage systems on ships and marine structures - Part 2: Sanitary drainage, drain piping for gravity systems
|
| ISO 15749-3-2004
| 船舶和海上技術.船舶和海上結構物的排水系統.第3部分:真空系統用衛生排水和排水管道
| Ships and marine technology - Drainage systems on ships and marine structures - Part 3: Sanitary drainage, drain piping for vacuum systems
|
| ISO 15837-2004
| 船舶和海上技術.管道系統中使用的有墊圈機械聯接件.性能規范
| Ships and marine technology - Gasketed mechanical couplings for use in piping systems - Performance specification
|
| ISO 15838-2003
| 船舶與海上技術.管道設施中使用的帶密封襯墊的機械耦合配件.性能規范
| Ships and marine technology - Fittings for use with gasketed mechanical couplings used in piping applications - Performance specification
|
| ISO 15840-2004
| 船舶和海上技術.用于海上設備的熱固性樹脂纖維管道和裝置的標準規范
| Ships and marine technology - Standard specification for thermosetting resin fibreglass pipe and fittings to be used for marine applications
|
| ISO 15874-1-2003
| 冷熱水裝置用塑料管道系統.聚丙烯(PP).第1部分:總則
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General
|
| ISO 15874-2-2003
| 冷熱水裝置用塑料管道系統.聚丙烯(PP).第2部分:管
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes
|
| ISO 15874-3-2003
| 冷熱水裝置用塑料管道系統.聚丙烯(PP).第3部分:配件
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings
|
| ISO 15874-5-2003
| 冷熱水裝置用塑料管道系統.聚丙烯(PP).第5部分:系統的適用性
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system
|
| ISO 15875-1-2003
| 冷熱水裝置用塑料管道系統.交聯聚乙烯(PE-X).第1部分:總則
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 1: General
|
| ISO 15875-2-2003
| 冷熱水裝置用塑料管道系統.交聯聚乙烯(PE-X).第2部分:管道
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 2: Pipes
|
| ISO 15875-3-2003
| 冷熱水裝置用塑料管道系統.交聯聚乙烯(PE-X).第3部分:配件
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings
|
| ISO 15875-5-2003
| 冷熱水裝置用塑料管道系統.交聯聚乙烯(PE-X).第5部分:系統的適用性
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system
|
| ISO 15876-1-2003
| 冷熱水裝置用塑料管道系統.聚丁烯(PB).第1部分:總則
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General
|
| ISO 15876-2-2003
| 冷熱水裝置用塑料管道系統.聚丁烯(PB).第2部分:管道
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes
|
| ISO 15876-3-2003
| 冷熱水裝置用塑料管道系統.聚丁烯(PB).第3部分:配件
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 3: Fittings
|
| ISO 15876-5-2003
| 冷熱水裝置用塑料管道系統.聚丁烯(PB).第5部分:系統的適用性
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 5: Fitness for purpose of the system
|
| ISO 15877-1-2003
| 冷熱水裝置用塑料管道系統.氯化聚氯乙烯(PVC-C).第1部分:總則
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General
|
| ISO 15877-2-2003
| 冷熱水裝置用塑料管道系統.氯化聚氯乙烯(PVC-C).第2部分:管道
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes
|
| ISO 15877-3-2003
| 冷熱水裝置用塑料管道系統.氯化聚氯乙烯(PVC-C).第3部分:配件
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings
|
| ISO 15877-5-2003
| 冷熱水裝置用塑料管道系統.氯化聚氯乙烯(PVC-C).第5部分:系統的適用性
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system
|
| ISO 15908-2002
| 熱塑性管道系統用膠粘劑.膠粘劑熱穩定性測定的試驗方法
| Adhesives for thermoplastic piping systems - Test method for the determination of thermal stability of adhesives
|
| ISO 16422-2006
| 由定向未增塑聚(氯)乙烯(PVC-O)制成的用于壓力下水運輸?shù)墓艿篮徒宇^.規范
| Pipes and joints made of oriented unplasticized poly(vinyl chloride) (PVC-O) for the conveyance of water under pressure - Specifications
|
| ISO 16708-2006
| 石油和天然氣工業.管道傳輸系統.基于可靠性的極限狀態法
| Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods
|
| ISO 16871-2003
| 塑料管道系統.塑料管道和配件.自然風化法
| Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering
|
| ISO 17454-2006
| 塑料管道系統.多層管道.用牽引裝置測試不同層粘性的試驗方法
| Plastics piping systems - Multilayer pipes - Test method for the adhesion of the different layers using a pulling rig
|
| ISO 17455-2005
| 塑料管道系統.多層管道.屏蔽管道的透氧性測定
| Plastics piping systems - Multilayer pipes - Determination of the oxygen permeability of the barrier pipe
|
| ISO 19220-2004
| 建筑物內土壤和廢物排放(低溫和高溫)用塑料管道系統.苯乙烯共聚物混合料(SAN + PVC)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Styrene copolymer blends (SAN + PVC)
|
| ISO 19921-2005
| 船舶和海上技術.帶彈性密封件的金屬管道部件的耐火性.試驗方法
| Ships and marine technology - Fire resistance of metallic pipe components with resilient and elastomeric seals - Test methods
|
| ISO 19922-2005
| 船舶和海上技術.帶彈性密封件的金屬管道部件的耐火性.試驗臺要求
| Ships and marine technology - Fire resistance of metallic pipe components with resilient and elastomeric seals - Requirements imposed on the test bench
|
| ISO 21329-2004
| 石油和天然氣工業.管道運輸系統.機械連接器的試驗過程
| Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors
|
| ISO 2186-1973
| 封閉管道中的流體流量 用于一次和二次元件間壓力信號傳輸?shù)倪B接法
| Fluid flow in closed conduits; Connections for pressure signal transmissions between primary and secondary elements
|
| ISO 24033-2006
| 耐升溫的聚乙烯管道(PE-RT).時間和溫度對預期強度的影響
| Pipes made of raised-temperature-resistance polyethylene (PE-RT) - Effect of time and temperature on the expected strength
|
| ISO 2975-1-1974
| 封閉管道中水流量的測量 示蹤法 第1部分:總則
| Measurement of water flow in closed conduits; Tracer methods; Part I : General
|
| ISO 2975-2-1975
| 封閉管道中水流量的測量 示蹤法 第2部分:用非放射性示蹤劑的恒速注入法
| Measurement of water flow in closed conduits; Tracer methods; Part II : Constant rate injection method using non-radioactive tracers
|
| ISO 2975-3-1976
| 封閉管道中水流量的測量 示蹤法 第3部分:用放射性示蹤劑的恒速注入法
| Measurement of water flow in closed conduits; Tracer methods; Part III : Constant rate injection method using radioactive tracers
|
| ISO 2975-6-1977
| 封閉管道中水流量的測量 示蹤法 第6部分:用非放射性示蹤劑的傳輸時間法
| Measurement of water flow in closed conduits; Tracer methods; Part VI : Transit time method using non-radioactive tracers
|
| ISO 2975-7-1977
| 封閉管道中水流量的測量 示蹤法 第7部分:用放射性示蹤劑的傳輸時間法
| Measurement of water flow in closed conduits; Tracer methods; Part VII : Transit time method using radioactive tracers
|
| ISO 3126-2005
| 塑料管道系統.塑料部件.尺寸測定
| Plastics piping systems - Plastics components - Determination of dimensions
|
| ISO 3183-1-1996
| 石油和天然氣工業 管道鋼管 交貨技術條件 第1部分:A級鋼管的要求
| Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 1: Pipes of requirement class A
|
| ISO 3183-2-1996
| 石油和天然氣工業 管道鋼管 交貨技術條件 第2部分:B級鋼管的要求
| Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 2: Pipes of requirements class B
|
| ISO 3183-3 Technical Corrigendum 1-2000
| 石油和天然氣工業 管道鋼管 交貨技術條件 第3部分:C級鋼管的要求 技術勘誤1
| Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 3: Pipes of requirement class C - Technical Corrigendum 1
|
| ISO 3183-3-1999
| 石油和天然氣工業 管道鋼管 交貨技術條件 第3部分:C級鋼管的要求
| Petroleum and natural gas industries - Steel pipe for pipelines - Technical delivery conditions - Part 3: Pipes of requirement class C
|
| ISO 3586-1976
| 玻璃設備、管道和配件 試驗、管理和使用的一般規則
| Glass plant, pipeline and fittings; general rules for testing, handling and use
|
| ISO 3587-1976
| 玻璃設備、管道和配件 公稱內徑15mm～150mm的管道和配件 通用性和互換性
| Glass plant, pipeline and fittings; Pipeline and fittings of nominal bore 15 to 150 mm; Compatibility and interchangeability
|
| ISO 3633-2002
| 建筑物內污廢水排放系統用硬聚氯乙烯(PVC-U)塑料管道系統(低溫和高溫)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U)
|
| ISO 4006-1991
| 封閉管道中流體流量的測量 詞匯和符號 兩種語言版
| Measurement of fluid flow in closed conduits; vocabulary and symbols
|
| ISO 4059-1978
| 聚乙烯(PE)管材 機械式管道連接系統壓降 試驗方法和要求
| Polyethylene (PE) pipes; Pressure drop in mechanical pipe-jointing systems; Method of test and requirements
|
| ISO 4144-2003
| 管道系統.符合ISO 7/1螺紋標準的不銹鋼配件
| Pipework - Stainless steel fittings threaded in accordance with ISO 7-1
|
| ISO 4179-2005
| 壓力和非壓力管道用球墨鑄鐵管和配件.水泥灰漿內襯
| Ductile iron pipes and fittings for pressure and non-pressure pipelines - Cement mortar lining
|
| ISO 4185 Technical Corrigendum 1-1993
| 封閉管道中液體流量的測量 重量法 技術勘誤1
| Measurement of liquid flow in closed conduits; weighing method; technical corrigendum 1
|
| ISO 4185-1980
| 封閉管道中液體流量的測量 重量法
| Measurement of liquid flow in closed conduits; Weighing method
|
| ISO 4435-2003
| 地下排水和排污水用塑料管道系統.未增塑聚氯乙烯
| Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U)
|
| ISO 4633-2002
| 橡膠密封.供水、排水和污水管道用密封圈.材料規范
| Rubber seals - Joint rings for water supply, drainage and sewerage pipelines - Specification for materials
|
| ISO 4704-1977
| 玻璃設備、管道和配件 玻璃設備元件
| Glass plant, pipeline and fittings; Glass plant components
|
| ISO 5136-2003
| 聲學.風機和其他風動設備輻射入管道中的聲功率的測定.管道法
| Acoustics - Determination of sound power radiated into a duct by fans and other air-moving devices - In-duct method
|
| ISO 5167-1 Technical Corrigendum 1-1997
| 用壓差裝置測量流體流量 第1部分:圓截面管道中插入的節流孔板、噴嘴和文杜利管 技術勘誤1
| Measurement of fluid flow by means of pressure differential devices - Part 1: Orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full - Technical Corrigendum 1
|
| ISO 5167-1-2003
| 用插入圓截面管道中的壓差裝置測量流體流量.第1部分:一般原理和要求
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements
|
| ISO 5167-2-2003
| 用插入圓截面管道中的壓差裝置測量流體流量.第2部分:節流孔板
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice plates
|
| ISO 5167-3-2003
| 用插入圓截面管道中的壓差裝置測量流體流量.第3部分:噴嘴和文杜利噴嘴
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 3: Nozzles and Venturi nozzles
|
| ISO 5167-4-2003
| 用插入圓截面管道中的壓差裝置測量流體流量.第4部分:文杜利管
| Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 4: Venturi tubes
|
| ISO 5176-1-1991
| 用壓差裝置測量流體流量.第1部分:圓截面管道中插入的節流孔板、噴嘴和文杜利管
| Measurement of fluid flow by means of pressure differential devices; part 1: orifice plates, nozzles and Venturi tubes inserted in circular cross-section conduits running full
|
| ISO 5667-5-2006
| 水質.采樣.第5部分:從水處理站和管道分配系統采樣飲用水的指南
| Water quality - Sampling - Part 5: Guidance on sampling of drinking water from treatment works and piped distribution systems
|
| ISO 5752-1982
| 法蘭連接的管道系統用金屬法蘭 結構長度和端面至中心的尺寸
| Metal valves for use in flanged pipe systems; Face-to-face and centre-to-face dimensions
|
| ISO 580-2005
| 塑料管和管道系統.噴射鑄造熱塑配件.熱效應直觀評估法
| Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating
|
| ISO 6412-1-1989
| 技術制圖 管道的簡化表示法 第1部分:通則和正交表示法
| Technical drawings; simplified representation of pipelines; part 1: general rules and orthogonal representation
|
| ISO 6412-2-1989
| 技術制圖 管道的簡化表示法 第2部分:等角投影
| Technical drawings; simplified representation of pipelines; part 2: isometric projection
|
| ISO 6412-3-1993
| 技術制圖 管道的簡化表示法 第3部分:通風和排放系統終端部件
| Technical drawings; simplified representation of pipelines; part 3: terminal features of ventilation and drainage systems
|
| ISO 6448-1985
| 橡膠密封件 輸送石油產品管道和配件用密封圈 材料規范
| Rubber seals; Joint rings used for petroleum product supply pipes and fittings; Specification for material
|
| ISO 6773-1994
| 航空航天 流體系統 管道及配件的熱沖擊試驗
| Aerospace - Fluid systems - Thermal shock testing of piping and fittings
|
| ISO 6817-1992
| 封閉管道中導電液體流量的測量 采用電磁流率計的方法
| Measurement of conductive liquid flow in closed conduits; method using electromagnetic flowmeters
|
| ISO 6944-1985
| 耐火試驗 通風管道
| Fire resistance tests; Ventilation ducts
|
| ISO 7235-2003
| 聲學.管道消音器和空氣界面裝置的實驗室測量步驟.插入損失、流動噪聲和總壓損失
| Acoustics - Laboratory measurement procedures for ducted silencers and air-terminal units - Insertion loss, flow noise and total pressure loss
|
| ISO 7268 AMD 1-1984
| 管道元件 公稱壓力的定義 修改1
| Amendment 1-1984
|
| ISO 7268-1983
| 管道元件 公稱壓力的定義
| Pipe components; Definition of nominal pressure
|
| ISO 7278-2-1988
| 液態烴 動態測量 計量校正系統 第2部分:管道校準
| Liquid hydrocarbons; dynamic measurement; proving systems for volumetric meters; part 2: pipe provers
|
| ISO 7278-4-1999
| 液態烴 動態測量 計量校正系統 第4部分:管道校正儀操作導則
| Liquid hydrocarbons - Dynamic measurement - Proving systems for volumetric meters - Part 4: Guide for operators of pipe provers
|
| ISO 7369-2004
| 管道工程.金屬軟管和軟管組件.詞匯
| Pipework - Metal hoses and hose assemblies - Vocabulary
|
| ISO 7396-1-2002
| 醫用燃?xì)夤艿老到y(tǒng).第1部分:醫用壓縮氣體和真空管道
| Medical gas pipeline systems - Part 1: Pipelines for compressed medical gases and vacuum
|
| ISO 7396-2-2000
| 醫用氣體管道系統 第2部分:麻醉用氣體凈化處理系統
| Medical gas pipeline systems - Part 2: Anaesthetic gas scavenging disposal systems
|
| ISO 7432-2002
| 玻璃纖維增強熱固性塑料管道和管配件.檢驗設計帶彈性體密封件的鎖緊套筒連接件,包括雙插孔連接件的試驗方法
| Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
|
| ISO 7509-2000
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管材 持續內壓力下破壞時間的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of time to failure under sustained internal pressure
|
| ISO 7510-1997
| 塑料管道系統 玻璃纖維增強塑料(GRP)元件 重量法測定成分
| Plastics piping systems - Glass-reinforced plastics (GRP) components - Determination of the amounts of constituents using the gravimetric method
|
| ISO 7511-1999
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管材和管件 確定短期內壓下管壁密封性的檢驗方法
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure
|
| ISO 7671-2003
| 建筑物內污、廢水排放(低溫和高溫)用塑料管道系統.聚丙烯(PP)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polypropylene (PP)
|
| ISO 7675-2003
| 建筑物內污、廢水(低溫和高溫)排放用塑料管道系統.氯化聚氯乙烯
| Plastic piping systems for soil and waste discharge (low and high temperature) inside buildings - Chlorinated poly(vinyl chloride) (PVC-C)
|
| ISO 7682-2003
| 建筑物內污、廢水排放(低溫和高溫)用塑料管道系統.丙烯腈-丁二烯-苯乙烯(ABS)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Acrylonitrile-butadiene-styrene (ABS)
|
| ISO 7684-1997
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管材 干燥條件下蠕變系數的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the creep factor under dry conditions
|
| ISO 7685-1998
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管材 初始有效環剛度的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness
|
| ISO 8277-1988
| 造船 管道系統 信息傳遞
| Shipbuilding; pipework; information transfer
|
| ISO 8316-1987
| 封閉管道中液體流量的測量 采用在容積計量容器內收集液體的方法
| Measurement of liquid flow in closed conduits; Method by collection of the liquid in a volumetric tank
|
| ISO 8513-2000
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管材 縱向抗拉特性的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of longitudinal tensile properties
|
| ISO 8521-1998
| 塑料管道系統 玻璃纖維增強熱固性塑料(GRP)管材 表面內周拉伸強度的測定
| Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength
|
| ISO 8770-2003
| 建筑物內污、廢水排放(低溫和高溫)用塑料管道系統.聚乙烯(PE)
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polyethylene (PE)
|
| ISO 8795-2001
| 輸送人類生活用水用塑料管道系統 流動評定 塑料管道和管件及其接頭的流動值的測定
| Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Determination of migration values of plastics pipes and fittings and their joints
|
| ISO 9080-2003
| 塑料管道和導管系統.用外推法測定熱塑性塑料管材的長期靜液壓強度
| Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
|
| ISO 9104-1991
| 封閉管道中流體流量的測量 液體電磁流量計性能評定方法
| Measurement of fluid flow on closed conduits; methods of evaluating the performance of electromagnetic flow-meters for liquids
|
| ISO 9170-1-1999
| 醫用氣體管道系統用終端設備 第1部分:供壓縮醫用設備和真空用的終端設備
| Terminal units for medical gas pipeline systems - Part 1: Terminal units for use with compressed medical gases and vacuum
|
| ISO 9170-2-1999
| 醫用氣體管道系統用終端設備 第2部分:麻醉氣體清除系統用的終端設備
| Terminal units for medical gas pipeline systems - Part 2: Terminal units for anaesthetic gas scavenging systems
|
| ISO 9311-1-2005
| 熱塑性管道系統用膠粘劑.第1部分:膜層特性的測定
| Adhesives for thermoplastic piping systems - Part 1: Determination of film properties
|
| ISO 9311-2-2002
| 熱塑管道系統的膠粘劑.第2部分:剪切強度的測定
| Adhesives for thermoplastic piping systems - Part 2: Determination of shear strength
|
| ISO 9311-3-2005
| 熱塑性管道系統用膠粘劑.第3部分:測定耐內壓力性的試驗方法
| Adhesives for thermoplastic piping systems - Part 3: Test method for the determination of resistance to internal pressure
|
| ISO 9349-2004
| 預絕緣球墨鑄鐵管道系統
| Preinsulated ductile iron pipeline systems
|
| ISO 9368-1-1990
| 采用稱重法測量封閉管道中液體的流量 校核裝置的規程 第1部分:靜態稱量系統
| Measurement of liquid flow in closed conduits by the weighing method; procedures for checking installations; part 1: static weighing systems
|
| ISO 9398-3-2003
| 工業洗衣機規范.容量和能耗特性定義和測試.第3部分:管道式洗滌機
| Specifications for industrial laundry machines - Definitions and testing of capacity and consumption characteristics - Part 3: Washing tunnels
|
| ISO 9631-2003
| 橡膠密封件.溫度為110℃及以下的熱水供給管道用密封圈.材料規范
| Rubber seals - Joint rings for pipelines for hot-water supply up to 110 degrees C - Specification for the material
|
| ISO 9803-1993
| 真空技術 管道配件 裝配尺寸
| Vacuum technology; pipeline fittings; mounting dimensions
|
| ISO 9853-1991
| 壓力管道系統用硬聚氯乙烯(PVC-U)管件 扁平試驗
| Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings for pressure pipe systems; crushing test
|
| ISO 9951 Technical Corrigendum 1-1994
| 封閉管道中氣體流量的測量 技術勘誤1
| Measurement of gas flow in closed conduits - Turbine meters; Technical Corrigendum 1
|
| ISO 9951-1993
| 封閉管道中氣體流量的測量 渦輪計
| Measurement of glas flow in closed conduits; turbine meters
|
| ISO/TR 11295-1992
| 用塑料管材和管件對管道系統的修復技術
| Techniques for rehabilitation of pipeline systems by the use of plastics pipes and fittings
|
| ISO/TR 12764-1997
| 封閉管道中流體流量的測量 在旋轉圓截面導管中插入渦流流量計來測量流率
| Measurement of fluid flow in closed conduits - Flowrate measurement by means of vortex shedding flowmeters inserted in circular cross-section conduits running full
|
| ISO/TR 3313-1998
| 封閉管道中流體流量的測量 流體脈動對流量測量?jī)x器影響的指南
| Measurement of fluid flow in closed conduits - Guidelines on the effects of flow pulsations on flow-measurement instruments
|
| ISO/TR 9824-1-1990
| 封閉管道的自由水面流測量 第1部分:測量方法
| Measurement of free surface flow in closed conduits; part 1: methods
|
| ISO/TR 9824-2-1990
| 封閉管道的自由水面流測量 第2部分:測量設備
| Measurement of free surface flow in closed conduits; part 2: equipment
|
| ISO/TS 15874-7-2003
| 冷熱水裝置用塑料管道系統.聚丙烯(PP).第7部分:合格評定指南
| Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 7: Guidance for the assessment of conformity
|
| ISO/TS 15875-7-2003
| 冷熱水裝置用塑料管道系統.交聯聚乙烯(PE-X).第7部分:合格評定指南
| Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity
|
| ISO/TS 15876-7-2003
| 冷熱水裝置用塑料管道系統.聚丁烯(PB).第7部分:合格評定指南
| Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 7: Guidance for the assessment of conformity
|
| ISO/TS 15877-7-2003
| 冷熱水裝置用塑料管道系統.氯化聚氯乙烯(PVC-C).第7部分:合格評定指南
| Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 7: Guidance for the assessment of conformity
|
| ISO/TS 7024-2005
| 建筑物內污水廢水排放用塑料管道系統(低溫和高溫).熱塑塑料.推薦的安裝規范
| Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Thermoplastics - Recommended practice for installation
|
| 編號 | 中文名稱 | 英文名稱 |
|---|