| 編號 | 中文名稱 | 英文名稱 |
|---|
| ANSI A112.14.1-1975
| 回水逆止閥
| Backwater valves
|
| ANSI B93.112M-1988
| 液壓氣動閥內部漏泄特性的測定方法
| Hydraulic Fluid Power - Valves - Method for Determining the Internal Leakage Characteristics
|
| ANSI B93.77M-1987
| 液壓氣動缸傳動安裝閥安裝表面的標準尺寸
| Hydraulic Fluid Power - Cylinder Actuator Mounted Valves - Standard Dimensions for Mounting Surfaces
|
| ANSI B93.9M-1969
| 流體動力閥上標記電導線和端口的符號
| Symbols for Marking Electrical Leads and Ports on Fluid Power Valves
|
| ANSI T1.330-1997
| 電信.電信環境用的閥調的鉛酸電池
| Telecommunications - Valve-regulated lead-acid batteries used in the telecommunications environment
|
| ANSI Z21.15-1997
| 煤氣設備、設備連接閥和軟管終端閥的手動煤氣閥(同 CGA 9.1)
| Manually Operated Gas Valves for Appliances, Appliance Connector Valves and Hose End Valves (same as CGA 9.1)
|
| ANSI Z21.15a-2001
| 煤氣設備、設備連接閥和軟管終端閥的手動煤氣閥(同 CGA 9.1a)
| Manually Operated Gas Valves for Appliances, Appliance Connector Valves and Hose End Valves (same as CGA 9.1a)
|
| ANSI Z21.21-2005
| 燃?xì)馄骶哂米詣?dòng)閥
| Automatic Valves for Gas Appliances (same as CSA 6.5)
|
| ANSI Z21.21b-2004
| 燃?xì)馄骶哂米詣?dòng)閥
| Automatic Valves for Gas Appliances (same as CSA 6.5b)
|
| ANSI Z21.22-1999
| 熱水供給系統用安全閥(與CSA 4.4-1998相同)
| Relief Valves for Hot Water Supply Systems (same as CSA 4.4-1998)
|
| ANSI Z21.22a Addenda-1990
| 熱水供給系統的安全閥和氣體自動關閉裝置.補充件
| Relief valves and automatic gas shutoff devices for hot water supply systems; Addenda
|
| ANSI Z21.22a-1999
| 減壓閥和真空截止閥
| Pressure Relief Valves and Vacuum Relief Valves
|
| ANSI Z21.22b-2001
| 熱水供應系統用截止閥
| Relief Valves for Hot Water Supply Systems (same as CSA 4.4b)
|
| ANSI Z21.79-1997
| 燃?xì)馄骶呃淠y
| Gas Appliances Sediment Traps
|
| ANSI Z21.79a-2005
| 燃?xì)馄骶叱搁y
| Gas Appliance Sediment Traps (Same as CGA 6.21a)
|
| ANSI/API 14A-2005
| 井下安全閥設備的規范
| Specification for Subsurface Safety Valve Equipment
|
| ANSI/API 553-1999
| 煉油控制閥
| Refinery Control Valve
|
| ANSI/API 574-1998
| 管、閥門及配件的檢驗
| Inspection of Piping, Tubing, Valves, and Fittings
|
| ANSI/API 599-2002
| 金屬塞閥.法蘭和焊接端
| Metal Plug Valves - Flanged and Welding Ends
|
| ANSI/API 603-2001
| 150級,鑄鐵,耐腐蝕,法蘭端閘閥
| Class 150, Cast, Corrosion-Resistant, Flanged-End Gate Valves
|
| ANSI/API 608-2002
| 對焊和法蘭端金屬球閥
| Metal Ball Valves - Flanged and Butt-Welding Ends
|
| ANSI/API 621-2001
| 金屬閘閥、球閥和止回閥的重新調整
| Reconditioning of Metallic Gate, Globe, and Check Valves
|
| ANSI/API Std.600-2001
| 石油和天然氣工業用螺栓接合鋼制帽狀閥門
| Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas Industries
|
| ANSI/API STD600-2001
| 石油和天然氣工業用栓緊帽狀鋼門閥
| Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas Industries
|
| ANSI/ARI 750-2001
| 制冷劑恒溫膨脹閥
| Thermostatic Refrigerant Expansion Valves
|
| ANSI/ARI 770-1994
| 制冷壓力調節閥
| Refrigerant Pressure Regulating Valves
|
| ANSI/ASHRAE 158.1-2004
| 制冷電磁閥的容量試驗方法
| Methods of Testing Capacity of Refrigerant Solenoid Valves
|
| ANSI/ASHRAE 17-1998
| 溫度調節用制冷安全閥容量分級測試方法
| Capacity Rating of Thermostatic Refrigerant Expansion Valves, Method of Testing for
|
| ANSI/ASME A112.14.1-2003
| 回水閥
| Backwater Valves
|
| ANSI/ASME A112.18.7M-1999
| 預防內部回流的立式浴缸/淋浴轉換閥
| Deck Mounted Bath/Shower Transfer Valves with Internal Backflow Prevention
|
| ANSI/ASME A112.4.1-1993
| 熱水器安全閥排水管
| Water Heater Relief Valve Drain Tubes
|
| ANSI/ASME A112.4.14-2004
| 衛生管道系統中使用的手動直角轉彎截止閥
| Manually Operated, Quarter-Turn Shutoff Valves for Use in Plumbing Systems
|
| ANSI/ASME B16.10-2003
| 閥門的面對面及端對端尺寸
| Face-to-Face and End-to-End Dimensions of Valves
|
| ANSI/ASME B16.33-2002
| 125表壓及以下的氣體管道系統中使用的手動金屬氣體閥
| Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig
|
| ANSI/ASME B16.34-2004
| 閥門.帶法蘭、有螺紋和焊接端部
| Valves - Flanged, Threaded and Welding End
|
| ANSI/ASME B16.38-1985
| 氣分配系統用大型手動金屬閥(NPS 2 1/2到12,最大壓力為125psig)
| Large Metallic Valves for Gas Distribution (Manually Operated, NPS 2 1/2 to 12, 125 psig Maximum)
|
| ANSI/ASME B16.40-2002
| 氣體分配系統中手動熱塑氣體截流閥及閥門
| Gas Shut-Offs and Valves in Gas Distribution Systems, Manually Operated Thermoplastic
|
| ANSI/ASME B16.44-2002
| 家用管道系統中使用的手工操作的金屬氣體閥門
| Manually Operated Metallic Gas Valves for Use in House Piping Systems
|
| ANSI/ASME B16.44a-1997
| 家庭管道系統中用手動金屬氣閥
| Manually Operated Metallic Gas Valves for Use in House Piping Systems
|
| ANSI/ASSE 1003-2001
| 水壓減壓閥的性能要求
| Performance Requirements for Water Pressure Reducing Valves
|
| ANSI/ASSE 1016-2005
| 單個淋浴裝置和浴盆/淋浴組合中淋浴裝置用自動補償閥門的性能要求
| Performance Requirements for Automatic Compensating Valves for Individual Showers and Showers in Tub/Shower Combinations
|
| ANSI/ASSE 1017-1999
| 主要用于家庭的溫控混合閥性能要求
| Performance Requirements for Temperature Actuated Mixing Valves for Primary Domestic Use
|
| ANSI/ASSE 1018-2002
| 分離器密封起動閥.輕便供水裝置
| Trap Seal Primer Valves - Potable Water Supplied
|
| ANSI/ASSE 1024-2004
| 雙重止回閥型防回流裝置
| Dual Check Valve Type Backflow Preventers
|
| ANSI/ASSE 1044-2002
| 分離器密封起動閥.排水裝置類型和電子設計類型
| Trap Seal Primer Devices - Drainage Types and Electronic Design Types
|
| ANSI/ASSE 1051-1998
| 污水管道系統用氣體導入閥
| Air Admittance Valves for Plumbing Drainage Systems
|
| ANSI/ASSE 1056-2002
| 倒虹吸回流真空關閉閥
| Back Siphonage Backflow Vacuum Breakers
|
| ANSI/ASSE 1069-2005
| 自動溫度控制混合閥門的性能要求
| Performance Requirements for Automatic Temperature Control Mixing Valves
|
| ANSI/ASTM A182/A 182M-2001
| 高溫設備用鍛制或軋制合金鋼管法蘭、鍛制管件、閥門及零件規范
| Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
|
| ANSI/ASTM B834-1996
| 壓力強化粉末冶金鐵鎳鉻鉬和鎳鉻鉬鈳(Nb)合金管法蘭、管配件、閥門和零件規范
| Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367) and Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625) Alloy Pipe Flanges, Fittings, Valves and Parts
|
| ANSI/ASTM D2713-2001
| 測定丙烷干燥性的試驗方法(閥門冷凍法)
| Test Method for Dryness of Propane (Valve Freeze Method)
|
| ANSI/ASTM D5500-1999
| 進氣閥沉淀物中汽車點火無鉛機油評估測試方法(05.03)
| Test Method for Vehicle Evaluation of Unleaded Automotive Spark-Ignition Engine Fuel for Intake Valve Deposit (05.03)
|
| ANSI/ASTM D6201-2004
| 進油閥沉積物形成用無鉛火花點火發動機燃料的功率計評價用試驗方法
| Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Value Deposit Formation
|
| ANSI/ASTM E1008-1997
| 地?zé)岷推渌邷貕毫υO(shè)備用閥身壓力釋放裝置的裝配、檢測和維護慣例
| Practice for Installation, Inspection, and Maintenance of Value Body Pressure Relief Methods for Geothermal and Other High-Temperature Applications
|
| ANSI/ASTM F1020-1997
| 船用管路截流閥慣例
| Practice for Line Blind Valves for Marine Applications
|
| ANSI/ASTM F1030-1986
| 閥門操作人員的實施規程
| Practice for Selection of Valve Operators
|
| ANSI/ASTM F1098-1987
| 蝶閥-NPS 2 到 24包封尺寸的規范
| Specification for Envelope Dimensions for Butterfly Valves - NPS 2 to 24
|
| ANSI/ASTM F1139-1988
| 疏水閥和排水管的規范
| Specification for Steam Traps and Drains
|
| ANSI/ASTM F1271-1997
| 船上儲罐液體過壓保護裝置溢流閥規范
| Specification for Spill Valves for Use in Marine Tank Liquid Overpressure Protections Applications
|
| ANSI/ASTM F1370-1992
| 艦船用水系統減壓閥的規范
| Specification for Pressure-Reducing Valves for Water Systems, Shipboard
|
| ANSI/ASTM F1508-1997
| 用于蒸汽、氣體和液體設備的角型減壓閥規范
| Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services
|
| ANSI/ASTM F1565-2000
| 蒸汽供應減壓閥規范
| Specification for Pressure-Reducing Valves for Steam Service
|
| ANSI/ASTM F1792-1997
| 氣態氧供氣閥門特殊要求規范
| Specification for Special Requirements for Valves Used in Gaseous Oxygen Service
|
| ANSI/ASTM F1793-1997
| 空氣或氮?dú)夤?yīng)截流閥(亦稱流量限制閥()規范
| Specification for Automatic Shut-Off Valves (also known as Excess Flow Valves EFV) for Air or Nitrogen Service
|
| ANSI/ASTM F1794-1997
| 氣體(除氧氣)和液壓系統手動球形閥門規范
| Specification for Hand-Operated Globe-Style Valves for Gas (Except Oxygen Gas) and Hydraulic Systems
|
| ANSI/ASTM F1795-2000
| 空氣或氮?dú)庀到y(tǒng)減壓閥規范
| Specification for Pressure-Reducing Valves for Air or Nitrogen Systems
|
| ANSI/ASTM F1802-2004
| 溢流閥性能試驗的試驗方法
| Test Method for Performance Testing of Excess Flow Valves
|
| ANSI/ASTM F1970-2005
| 聚氯乙烯(PVC)或氯化聚氯乙烯(CPVC)系統專用工程配件、附件或閥門的規范
| Specification for Special Engineered Fittings, Appurtenances or Valves for Use in Poly(Vinyl Chloride) (PVC) or Chlorinated Poly(Vinyl Chloride) (CPVC) Systems
|
| ANSI/ASTM F1985-1999
| 氣動球形控制閥規范
| Specification for Pneumatic-Operated, Globe-Style, Control Valves
|
| ANSI/ASTM F2138-2001
| 天然氣設備溢流閥規范
| Specification for Excess Flow Valves for Natural Gas Service
|
| ANSI/ASTM F2324-2003
| 預清洗噴霧閥的試驗方法
| Test Method for Pre-rinse Spray Valves
|
| ANSI/ASTM F885-1997
| 美國標準直管螺紋1/4至2英寸青銅球閥閥殼尺寸規范
| Specification for Envelope Dimensions for Bronze Globe Valves NPS 1/4 to 2
|
| ANSI/ASTM F992-1997
| 閥門標識牌規范
| Specification for Valve Label Plates
|
| ANSI/ASTM F993-1997
| 閥門鎖緊裝置規范
| Specification for Valve Locking Devices
|
| ANSI/AWWA C500-2002
| 排水和污水系統閘門閥
| Gate Valves for Water and Sewage Systems
|
| ANSI/AWWA C504-2006
| 橡膠墊密封蝶閥
| Rubber-Seated Butterfly Valves
|
| ANSI/AWWA C507-2005
| 從6英寸(150mm)到48英寸(1200mm)的球閥
| Ball Valves 6 in (150 mm) through 48 in (1200 mm)
|
| ANSI/AWWA C508-2001
| 2in(50mm)-24in(600mm)NPS水廠設備擺動止回閥
| Swing-Check Valves for Waterworks Service, 2 in (50 mm) through 24 in (600 mm) NPS
|
| ANSI/AWWA C510-1997
| 雙止回閥防回流組件
| Double Check Valve Backflow-Prevention Assembly
|
| ANSI/AWWA C512-2004
| 給水裝置用放氣閥、空氣/真空和混合空氣閥
| Air Release, Air/Vacuum, and Combination Air Valves for Water Works Service
|
| ANSI/AWWA C517-2005
| 彈性座式鑄鐵偏心塞閥
| Resilient-Seated Cast Iron Eccentric Plug Valves
|
| ANSI/AWWA C540-2002
| 閥門和水閘用作動裝置
| Power-Actuating Devices for Valves and Sluice Gates
|
| ANSI/AWWA C550-2005
| 閥門和給水栓用防護性內部涂層
| Protective Interior Coatings for Valves and Hydrants
|
| ANSI/AWWA C800-2005
| 地下管道閥門和配件
| Underground Service Line Valves and Fittings
|
| ANSI/FCI 69-1-1989
| 疏水閥的壓力額定值標準
| Pressure Rating Standard for Steam Traps
|
| ANSI/FCI 91-1-1997
| 控制閥門密性封的鑒定標準
| Standard for Qualification of Control Valve Stem Seals
|
| ANSI/IAS NGV4.6-1999
| 天然氣分裝系統手動控制閥
| Manually Operated Valves for Natural Gas Dispensing Systems
|
| ANSI/IAS NGV4.7-1999
| 天然氣分裝系統用自動壓力控制閥
| Automatic Pressure-Operated Valves for Natural Gas Dispensing Systems
|
| ANSI/IEEE 1187-2002
| 固定用途的閥調節鉛酸蓄電池的安裝設計和安裝的推薦實施規程
| Recommended Practice for Installation Design and Installation of Valve Regulated Lead-Acid Storage Batteries for Stationary Applications
|
| ANSI/IEEE 1189-1996
| 固定設備用的閥調節鉛酸(VRLA)蓄電池的選擇指南
| Guide for the Selection of Valve-Regulated Lead-Acid (VRLA) Batteries for Stationary Application
|
| ANSI/IEEE 1290-1996
| 核電站電動控制閥門電機的應用、保護、控制和試驗指南
| Guide for MOV (Motor-Operated Valve) Motor Application, Protection, Control, and Testing in Nuclear Power Generating Stations
|
| ANSI/IEEE 382-1996
| 核電廠用帶安全相關功能的電力操作閥組件的執行機構的合格鑒定
| Actuators for Power-Operated Valve Assemblies with Safety-Related Functions for Nuclear Power-Plants, Qualification of
|
| ANSI/IEEE 857-1996
| 高壓直流可控硅換流閥試驗程序的推薦實施規程
| Recommended Practice for Test Procedures for High Voltage Direct Current Thyristor Valves
|
| ANSI/IEEE C62.32-2004
| 氣隙電涌防護裝置(閥門和沖出式裝置除外)的低壓試驗規范
| Air Gap Surge-Protective Devices (Excluding Valve and Expulsion-Type Devices), Test Specifications for the Low-Voltage
|
| ANSI/IIAR 3-2005
| 氨制冷機閥門
| Ammonia Refrigeration Valves
|
| ANSI/ISA 75.01.01-2002
| 尺寸控制閥用流量方程式
| Flow Equations for Sizing Control Valves
|
| ANSI/ISA 75.02-1996
| 控制閥能力試驗程序
| Control Valve Capacity Test Procedures
|
| ANSI/ISA 75.04-1995
| 無凸緣控制閥的端面間尺寸(ANSI類型150、300和600)
| Face-to-Face Dimensions of Flangeless Control Valves (ANSI Classes 150, 300, and 600)
|
| ANSI/ISA 75.05.01-2001
| 控制閥術語
| Control Valve Terminology
|
| ANSI/ISA 75.08-1999
| 安裝好的凸緣夾具或夾緊閥的端面間尺寸
| Installed Face-to-Face Dimensions for Flanged Clamp or Pinch Valves
|
| ANSI/ISA 75.08.01-2002
| 整體式帶凸緣的球型(類型125、150、250、300和600)控制閥體的端面間尺寸
| Face-to-Face Dimensions for Integral Flanged Globe-Style Control Valve Bodies (Classes 125, 150, 250, 300, and 600)
|
| ANSI/ISA 75.08.02-2003
| 無凸緣的控制閥端面間的尺寸(級別150、300和600)
| Face-to-Face Dimensions for Flangeless Control Valves (Classes 150, 300, and 600)
|
| ANSI/ISA 75.08.03-2001
| 承插焊接端和螺旋端球型控制閥的端面間尺寸(ANSI類型150、300、600、900、1500和2500)
| Face-to-Face Dimensions for Socket Weld-End and Screwed-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 1500, and 2500)
|
| ANSI/ISA 75.08.04-2001
| 對焊端球型控制閥的端面尺寸
| Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves
|
| ANSI/ISA 75.08.05-2002
| 端面對焊球型(類型150、300、600、900、1500和2500)控制閥的端面間尺寸
| Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves (Classes 150, 300, 600, 900, 1500, and 2500)
|
| ANSI/ISA 75.08.06-2002
| 帶凸緣的球型(類型900、1500和2500)控制閥體的面對面尺寸
| Face-to-Face Dimensions for Flanged Globe-Style Control Valve Bodies (Classes 900, 1500, and 2500)
|
| ANSI/ISA 75.08.07-2001
| 可分離的凸緣球型控制閥的端面間尺寸(類型150、300和600)
| Face-to-Face Dimensions for Separable Flanged Globe-Style Control Valves (Classes 150, 300, and 600)
|
| ANSI/ISA 75.08.09-2005
| 滑動桿無凸緣控制閥的端面間尺寸(類型150、300和600)
| Face-to-Face Dimensions for Sliding Stem Flangeless Control Valves (Classes 150, 300, and 600)
|
| ANSI/ISA 75.11.01-1985
| 控制閥的固有流量特征和可調范圍
| Control Valves, Inherent Flow Characteristic and Rangeability of
|
| ANSI/ISA 75.19.01-2001
| 控制閥水壓試驗
| Hydrostatic Testing of Control Valves
|
| ANSI/ISA 75.22-1999
| 凸緣球型角度控制閥身的端面至中心間尺寸
| Face-to-Centering Dimensions for Flanged Globe-Style Angle Control Valve Bodies
|
| ANSI/ISA 75.25.01-2001
| 步進輸入控制閥反應測量試驗程序
| Test Procedures for Control Valve Response Measurement from Step Inputs
|
| ANSI/ISA S75.02-1996
| 控制閥容量測試程序
| Control Valve Capacity Test Procedures
|
| ANSI/ISA S75.04-1995
| 無法蘭控制閥端間尺寸(ANSI 150,300和600級)
| Face-to-Face Dimensions of Flangeless Control Valves (ANSI Classes 150, 300, and 600)
|
| ANSI/ISA S75.08-1985
| 法蘭夾具或夾緊閥的安裝面與面間尺寸
| Installed Face-to-Face Dimensions for Flanged Clamp or Pinch Valves
|
| ANSI/ISA S75.08.03-2001
| 承插焊接端頭和螺旋端頭球狀控制閥的面到面尺寸
| Face-to-Face Dimensions for Socket Weld-End and Screwed-End Globe-Style Control Valves (ANSI Classes 150, 300, 600, 900, 1500, and 2500)
|
| ANSI/ISA S75.08.04-2001
| 對焊端頭球狀控制閥的面到面尺寸
| Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves
|
| ANSI/ISA S75.08.07-2001
| 獨立法蘭球狀控制閥的面到面尺寸
| Face-to-Face Dimensions for Separable Flanged Globe-Style Control Valves (Classes 150, 300, and 600)
|
| ANSI/ISA S75.11-1985
| 控制閥內在流量特性和幅度變化量
| Control Valves, Inherent Flow Characteristic and Rangeability of
|
| ANSI/ISA S75.14-1984
| 對焊端球型控制閥端間尺寸
| Face-to-Face Dimensions for Buttweld-End Globe-Style Control Valves
|
| ANSI/ISA S75.19.01-2001
| 控制閥靜水壓試驗
| Hydrostatic Testing of Control Valves
|
| ANSI/ISA S75.22-1992
| 法蘭球式角度控制閥體的端面至中心尺寸
| Face-to-Centering Dimensions for Flanged Globe-Style Angle Control Valve Bodies
|
| ANSI/ISA S93.00.01-1999
| 手動和自動關閉閥門外泄露評估的標準方法
| Standard Method for the Evaluation of External Leakage of Manual and Automated On-Off Valves
|
| ANSI/ISA TR75.25.02-2000
| 階式信號輸入控制閥反應測量
| Control Valve Response Measurement from Step Inputs
|
| ANSI/NFPA 1964-2003
| 噴嘴(關閉閥和端頭)
| Spray Nozzles (Shutoff and Tip)
|
| ANSI/SAE J1118-1993
| 摩托車制動系統試驗程序用液壓閥
| Hydraulic Valves for Motor Vehicle Brake Systems Test Procedure
|
| ANSI/SAE J1409-1998
| 空氣制動閥試驗程序
| Air Brake Valves Test Procedure
|
| ANSI/SAE J1410-1998
| 空氣制動閥.性能要求
| Air Brake Valve - Performance Requirements
|
| ANSI/SAE J351-1994
| 油回火碳素鋼閥、彈簧鋼絲和彈簧
| Oil Tempered Carbon Steel Valve, Spring Quality Wire, and Springs
|
| ANSI/UL 1002-1996
| 分類危險場所用電動閥
| Electrically Operated Valves for Use in Hazardous (Classified) Locations
|
| ANSI/UL 125-2001
| 無水氨和液化氣閥門的安全標準（安全閥除外）
| Standard for Safety for Valves for Anhydrous Ammonia and LP-Gas (Other than Safety Relief)
|
| ANSI/UL 132-2002
| 無水氨氣和液化石油氣的安全閥的安全標準
| Standard for Safety for Safety Relief Valves for Anhydrous Ammonia and LP-Gas
|
| ANSI/UL 144-2001
| 液化石油氣壓力調節閥的安全標準
| Standard for Safety for Pressure-Regulating Valves for LP Gas
|
| ANSI/UL 1468-2004
| 消防設施用直接作用的降壓和控壓閥
| Direct-Acting Pressure-Reducing and Pressure-Control Valves for Fire Protection Service
|
| ANSI/UL 1478-2004
| 消防水泵減壓閥
| Fire Pump Relief Valves
|
| ANSI/UL 1486-2003
| 防火設施用干管閥快速打開裝置的安全標準
| Standard for Safety for Quick Opening Devices for Dry Pipe Valves for Fire Protection Service
|
| ANSI/UL 1739-2004
| 消防用液壓控制閥
| Pilot-Operated Pressure-Control Valves for Fire-Protection Service
|
| ANSI/UL 193-2003
| 防火設施用報警閥門
| Alarm Valves for Fire-Protection Service
|
| ANSI/UL 312-2003
| 防火設施用止回閥
| Check Valves for Fire-Protection Service
|
| ANSI/UL 668-2004
| 消防設備用水帶閥
| Hose Valves for Fire Protection Service
|
| ANSI/UL 753-1996
| 消防裝置用自動供水控制閥的警報附件
| Alarm Accessories for Automatic Water-Supply Control Valves for Fire-Protection Service
|
| ANSI/UL 842-1999
| 易燃液用閥門
| Valves for Flammable Fluids
|
| ASME A112.14.1-1975
| 回水閥門
| (Backwater valves)
|
| ASME A112.18.7-1999
| 裝蓋板的帶整體回流保護的浴室/淋浴轉換閥
| (Deck mounted bath/shower transfer valves with integral backflow protection)
|
| ASME A112.4.1-1993
| 熱水器減壓閥排水管
| (Water heater relief valve drain tubes)
|
| ASME B 16.40 Erratum-2003
| 燃?xì)夥峙湎到y(tǒng)中的手動熱塑性氣體開關和閥門.對ASME B 16.40-2002的勘誤
| (Manually operated thermoplastic gas shutoffs and valves in gas distribution systems; Erratum to ASME B16.40-2002)
|
| ASME B16.10-2000
| 閥的面對面及端對端尺寸
| (Face-to-face and end-to-end dimensions of valves)
|
| ASME B16.33-2002
| 125表壓及以下的氣體管道系統中使用的手動金屬氣閥
| (Manually operated metallic gas valves for use in gas piping systems up to 125 psi (sizes NPS 1/2 through NPS 2))
|
| ASME B16.34-1996
| 閥門.法蘭、螺紋和焊接端
| (Valves - Flanged, threaded, and welding end)
|
| ASME B16.34a Addenda-1998
| 帶螺紋的法蘭式閥門和焊接端.附錄
| (Valves - Flanged, threaded, and welding end; Addenda)
|
| ASME B16.38-1985
| 氣體分配系統中用手動大型金屬閥門(NPS 2 1/2到12,其最大允許表壓不超過125巴)
| (Large metallic valves for gas distribution (manually operated, NPS 2 1/2 to 12, 125 psig maximum))
|
| ASME B16.40-2002
| 氣體分配系統中的手動熱塑性氣體截流閥及閥門
| (Manually operated thermoplastic gas shutoffs and valves in gas distribution systems)
|
| ASME B40.6-1994
| 限壓閥
| (Pressure limiter valves)
|
| ASME N278.1-1975
| 與安全相關的自動和機動閥門.功能規范標準
| (Self-operated and power-operated safety-related valves - Functional specification standard)
|
| ASME PTC 25.3-1988
| 安全和減壓閥
| (Safety and relief valves)
|
| ASME Y32.2.3-1949
| 管道配件,閥門,管道配置用圖形符號
| (Graphical symbols for pipe fittings, valves and piping)
|
| ASTM A 126-2004
| 閥門、法蘭和管配件用灰鐵鑄件的標準規范
| Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings
|
| ASTM A 182/A 182Ma-2005
| 高溫設備用鍛制或軋制合金鋼管法蘭、鍛制管件、閥門及零件的標準規范
| Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
|
| ASTM A 230/A 230M-2005
| 閥簧級油回火碳素鋼絲的標準規范
| Standard Specification for Steel Wire, Oil-Tempered Carbon Valve Spring Quality
|
| ASTM A 232/A 232M-2005
| 閥簧級鉻礬合金鋼的標準規范
| Standard Specification for Chromium-Vanadium Alloy Steel Valve Spring Quality Wire
|
| ASTM A 338-1984
| 鐵路,船舶和其他重型裝備在溫度達到650華氏度(345攝氏度)時使用的可鍛鑄鐵法蘭,管件和閥門零件
| Malleable Iron Flanges, Pipe Fittings and Valve Parts for Railroad, Marine and Other Heavy Duty Service at Temperatures up to 650 Degrees F (345 Degrees C)
|
| ASTM A 522/A 522M-2001
| 低溫設備用鍛制或軋制含鎳8%和9%的合金鋼法蘭、配件、閥門和零件的標準規范
| Standard Specification for Forged or Rolled 8 and 9% Nickel Alloy Steel Flanges, Fittings, Valves, and Parts for Low-Temperature Service
|
| ASTM A 694/A 694M-2003
| 高壓傳輸設備用管法蘭、配件、閥門及零件用碳素鋼及合金鋼鍛件的標準規范
| Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts for High-Pressure Transmission Service
|
| ASTM A 877/A 877M-2005
| 閥簧級鉻硅合金鋼絲的標準規范
| Standard Specification for Steel Wire, Chromium-Silicon Alloy Valve Spring Quality
|
| ASTM A 878/A 878M-2005
| 閥簧級改進的鉻硅合金鋼絲的標準規范
| Standard Specification for Steel Wire, Modified Chromium Vanadium Valve Spring Quality
|
| ASTM A 961/A 961M-2005
| 管道設施用鋼法蘭、鍛件、閥門和部件的通用要求的標準規范
| Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications
|
| ASTM A 988/A 988M-2005
| 高溫設備用熱等靜壓壓制的不銹鋼法蘭、配件、閥門和部件的標準規范
| Standard Specification for Hot Isostatically-Pressed Stainless Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
|
| ASTM A 989/A 989M-2005
| 高溫設備用熱等靜壓壓制的合金鋼法蘭、配件、閥門和部件的標準規范
| Standard Specification for Hot Isostatically-Pressed Alloy Steel Flanges, Fittings, Valves, and Parts for High Temperature Service
|
| ASTM B 61-2002
| 蒸氣或閥門青銅鑄件的標準規范
| Standard Specification for Steam or Valve Bronze Castings
|
| ASTM B 763-2004
| 閥門用銅合金砂型鑄件標準規范
| Standard Specification for Copper Alloy Sand Castings for Valve Applications
|
| ASTM B 834-1995
| 壓力強化粉末冶金鐵鎳鉻鉬和鎳鉻鉬鈳(Nb)合金管法蘭、管配件、閥門和零件標準規范
| Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367) and Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625) Alloy Pipe Flanges, Fittings, Valves, and Parts
|
| ASTM C 1129-1989
| 通過給凸面閥門及法蘭增加熱絕緣材料評估蓄熱量的標準實施規程
| Standard Practice for Estimation of Heat Savings by Adding Thermal Insulation to Bare Valves and Flanges
|
| ASTM D 2512-1995
| 材料與液氧兼容性標準試驗方法(沖擊敏感閥與可靠性技術)
| Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques)
|
| ASTM D 2713-1991
| 丙烷干燥性的標準試驗方法(閥凍結法)
| Standard Test Method for Dryness of Propane (Valve Freeze Method)
|
| ASTM D 3076-2000
| 氣溶膠容器外部卷合閥的有效卷合度的標準試驗方法
| Standard Test Methods for Effective Crimping on Outside Crimped Valves of Aerosol Containers
|
| ASTM D 3089-1997
| 測量氣溶膠閥填料斜管A-D尺寸的標準操作規程
| Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
|
| ASTM D 5500-1998
| 進液閥門沉積形成的不含鉛自動火花點火引擎燃料的車輛評價標準試驗方法
| Standard Test Method for Vehicle Evaluation of Unleaded Automotive Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
|
| ASTM D 6201-2004
| 進油閥沉積物形成用火花點燃式發動機無鉛燃料的功率計評定標準試驗方法
| Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
|
| ASTM E 1008-2003
| 地?zé)岷推渌邷匾后w設備用減壓閥體的安裝、檢驗及維修用標準實施規范
| Standard Practice for Installation, Inspection, and Maintenance of Valve-body Pressure-relief Methods for Geothermal and Other High-Temperature Liquid Applications
|
| ASTM E 675-2002
| 可互換的圓錐接地旋塞閥和栓塞的標準規范
| Standard Specification for Interchangeable Taper-Ground Stopcocks And Stoppers
|
| ASTM E 911-1998
| 有聚四氟乙烯(PTFE)插頭的玻璃管旋塞閥標準規范
| Standard Specification for Glass Stopcocks with Polytetrafluoroethylene (PTFE) Plugs
|
| ASTM F 1020-1986
| 船用暗線閥
| Standard Specification for Line-Blind Valves for Marine Applications
|
| ASTM F 1030-1986
| 閥門操作器的選擇
| Standard Practice for Selection of Valve Operators
|
| ASTM F 1094-1987
| 用直接加壓分接抽樣閥和用預先消毒塑料包法對電子和微電子器件加工用水微生物監測的測試方法
| Test Methods for Microbiological Monitoring of Water Used for Processing Electron and Microelectronic Devices by Direct Pressure Tap Sampling Valve and by the Presterilized Plastic Bag Method
|
| ASTM F 1098-1987
| 管子公稱尺寸2-24號用蝶閥外殼尺寸
| Standard Specification for Envelope Dimensions for Butterfly Valves-NPS 2 to 24
|
| ASTM F 1139-1988
| 蒸汽疏水閥和排水管
| Standard Specification for Steam Traps and Drains
|
| ASTM F 1271-1990
| 船上儲罐液體過壓保護裝置用溢流閥
| Standard Specification for Spill Valves for Use in Marine Tank Liquid Overpressure Protections Applications
|
| ASTM F 1370-1992
| 船上給水系統用減壓閥
| Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard
|
| ASTM F 1373-1993
| 氣體分配系統組件用自動閥的周期壽命測定的標準試驗方法
| Standard Test Method for Determination of Cycle Life of Automatic Valves for Gas Distribution System Components
|
| ASTM F 1394-1992
| 測定從氣體分配系統閥門產生的粒子成分的標準試驗方法
| Standard Test Method for Determination of Particle Contribution from Gas Distribution System Valves
|
| ASTM F 1431-1992
| 柴油機排氣阻水閥
| Standard Specification for Water Trap for Diesel Exhaust
|
| ASTM F 1508-1996
| 用于蒸汽、氣體和液體設備的角型減壓閥標準規范
| Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas and Liquid Services
|
| ASTM F 1565-2000
| 蒸汽設備用減壓閥標準規范
| Standard Specification for Pressure-Reducing Valves for Steam Service
|
| ASTM F 1792-1997
| 用于氧氣服務的閥門的特殊要求的標準規范
| Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service
|
| ASTM F 1793-1997
| 空氣或氮服務用自動截流閥(也稱為溢流閥)的標準規范
| Standard Specification for Automatic Shut-Off Valves (Also Known as Excess Flow Valves, EFV) for Air Or Nitrogen Service
|
| ASTM F 1794-1997
| 手動、球型閥氣體(除氧氣)和液壓系統標準規范
| Standard Specification for Hand-Operated, Globe-Style Valves for Gas (Except Oxygen Gas), and Hydraulic Systems
|
| ASTM F 1795-2000
| 空氣或氮?dú)庀到y(tǒng)用減壓閥標準規范
| Standard Specification for Pressure-Reducing Valves for Air or Nitrogen Systems
|
| ASTM F 1802-2004
| 溢流閥性能測試標準試驗方法
| Standard Test Method for Performance Testing of Excess Flow Valves
|
| ASTM F 1970-2005
| 聚氯乙烯(PVC)或氯化聚氯乙烯(CPVC)系統中使用的專用工程配件、附件或閥門的標準規范
| Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems
|
| ASTM F 1985-1999
| 氣動球形控制閥標準規范
| Standard Specification for Pneumatic-Operated, Globe-Style, Control Valves
|
| ASTM F 2138-2001
| 天然氣設備用溢流閥標準規范
| Standard Specification for Excess Flow Valves for Natural Gas Service
|
| ASTM F 2215-2005
| 軸承、閥門和軸承設備用黑色和有色金屬滾珠軸承標準規范
| Standard Specification for Balls, Bearings, Ferrous and Nonferrous for Use in Bearings, Valves, and Bearing Applications |
| ASTM F 2324-2003
| 預清洗噴霧器閥用標準試驗方法
| Standard Test Method for Prerinse Spray Valves
|
| ASTM F 885-1984
| 美國標準直管螺紋1/4至2英寸青銅球型閥的閥殼尺寸標準規范
| Standard Specification for Envelope Dimensions for Bronze Globe Valves NPS 1/4 to 2
|
| ASTM F 992-1986
| 閥門標識牌
| Standard Specification for Valve Label Plates
|
| ASTM F 993-1986
| 閥門鎖緊裝置標準規范
| Standard Specification for Valve Locking Devices
|
| IEEE 1187-2002
| 固定設備用的閥調節鉛酸蓄電池的安裝設計和安裝的推薦性實施規程
| (Recommended practice for installation design and installation of valve-regulated lead-acid storage batteries for stationary applications)
|
| IEEE 1188-1996
| 發電站用閥調節鉛酸(VRLA)蓄電池組的保養、試驗和更新的推薦規程
| (Recommended practice for maintenance, testing, and replacement of valve-regulated lead-acid (VRLA) batteries for stationary applications)
|
| IEEE 1189-1996
| 固定設備用調節閥鉛酸(VRLA)蓄電池的選擇指南
| (Guide for selection of valve-regulated lead-acid (VRLA) batteries for stationary applications)
|
| IEEE 1290-1996
| 核電站中電動閥門(MOV)的電機使用,保護,控制和試驗的指南
| (Guide for motor operated valve (MOV) motor application, protection, control, and testing in nuclear power generating stations)
|
| IEEE 382-1996
| 對核電站用有安全功能的電動閥組驅動器的鑒定
| (Qualification of actuators for power-operated valve assemblies with safety-related functions for nuclear power plants)
|
| IEEE 857-1996
| 高壓直流半導體閘流管閥試驗程序推薦規程
| (Recommended practice for test procedures for high-voltage direct-current thyristor valves)
|
| UL 1002-1994
| 危險(分類的)場所用電動閥門
| (Electrically operated valves for use in hazardous (classified) locations )
|
| UL 1091-1994
| 消防裝置用蝶閥
| (Butterfly valves for fire-protection service )
|
| UL 1106-1998
| 船舶用可燃液體人工操作斷流閥
| (Marine manually operated shutoff valves for flammable liquids )
|
| UL 1121-1998
| 船用貫穿船身的配件和舷側進水閥
| (Marine through-hull fittings and sea-valves )
|
| UL 125-1997
| 無水液氨和液化石油氣閥門(不包括安全卸荷閥)
| (Valves for anhydrous ammonia and LP-gas (other than safety relief) )
|
| UL 132-1997
| 無水液體石油氣用安全卸荷閥門
| (Safety relief valves for anhydrous ammonia and LP-gas )
|
| UL 144-1999
| 液化石油氣調節閥
| (LP-gas regulators )
|
| UL 1468-1995
| 防火設備用直接控制的減壓閥和壓力控制閥
| (Direct acting pressure reducing and pressure restricting valves )
|
| UL 1469-1995
| 回流專用止回閥的閥身強度和液壓損失率檢驗
| (Strength of body and hydraulic pressure loss testing of backflow special check valves )
|
| UL 1478-1995
| 消防泵減壓閥
| (Fire pumps relief valves )
|
| UL 1486-2004
| 消防設備用干管閥門的快速開啟裝置
| (Quick opening devices for dry pipe valves for fire protection service )
|
| UL 17-1994
| 燃油設備用通風孔或煙囪連接器調節閥門
| (Vent or chimney connector dampers for oil-fired appliances )
|
| UL 1726-2001
| 儲水系統用自動排水閥
| (Automatic drain valves for standpipe systems )
|
| UL 1739-1994
| 消防設備用液壓控制的壓力控制閥
| (Pilot-operated pressure-control valves for fire-protection service )
|
| UL 1769-2003
| 氣瓶閥
| (Cylinder valves )
|
| UL 193-2004
| 防火用報警閥門
| (Alarm valves for fire-protection service )
|
| UL 260-1994
| 防火用蒸汽收集器和和集水閥門
| (Dry pipe and deluge valves for fire-protection service )
|
| UL 262-2004
| 防火用閘閥
| (Gate valves for fire-protection service )
|
| UL 312--2004
| 防火用切斷閥
| (Check valves for fire-protection service )
|
| UL 352-1997
| 恒定液面油閥門
| (Constant-level oil valves )
|
| UL 429-1999
| 電動控制閥
| (Electrically operated valves )
|
| UL 668-1995
| 消防用軟管閥門
| (Hose valves for fire-protection service )
|
| UL 753-1995
| 消防裝置用自動供水控制閥報警附件
| (Alarm accessories for automatic water-supply control valves for fire protection service )
|
| UL 842-1997
| 可燃流體用閥門
| (Valves for flammable fluids )
|
| 編號 | 中文名稱 | 英文名稱 |
|---|