| 編號 | 中文名稱 | 英文名稱 |
|---|
| NF A32-060-2001
| 鑄造產品.泵、閥門和配件用鑄鋼件和鎳合金鑄件(內部部件和防護殼體)
| (Foundry products - Cast steel and nickel alloy castings for pumps, valves and fittings (enclosures and internal components).)
|
| NF A72-115-1966
| 高爐附件.熱風閥.閥蓋和底座（PN6）
| (BLAST FURNACE ACCESSORIES. HOT AIR VALVES. DISCS AND SEATS,PN 6.)
|
| NF A72-120-1973
| 鋼鐵廠.氣體管道和大直徑閥.帶法蘭的接頭（PN6）
| (LARGE DIAMETER PIPES AND VALVES FOR GASEOUS FLUIDS. FLANGE CONNECTIONS PN 6.)
|
| NF A84-330-1982
| 氣焊設備.乙炔發生器用“防回氣—斷火”的液壓安全閥和組合裝置.規范和試驗
| (GAS WELDING EQUIPMENT. HYDRAULIC SAFETY SEALS AND COMBINED “NON-RETURN VALVE/FLAME ARRESTOR“ DEVICES FOR ACETYLENE GENERATORS. REQUIREMENTS AND TESTS.)
|
| NF A84-420-1991
| 氣焊設備和有關方法.減壓閥入品接頭.尺寸
| (Equipment for gas welding and allied processes. Pressure regulators inlet connections. Dimensions.)
|
| NF A84-621-2002
| 氣焊設備.焊接、切割和相關工藝用帶截止閥的速動連接
| (Gas welding equipment - Quick-action coupling with shut-off valves for welding, cutting and allied processes.)
|
| NF B35-792-2003
| 實驗室用旋塞和閥門的顏色編碼
| (Colour coding of taps and valves for use in laboratories.)
|
| NF B51-078-1-2001
| 木基板.結構設計的特性閥門.第1部分:OSB.顆粒板和纖維板
| (Wood-based panels - Characteristic values for structural design - Part 1 : OSB, particleboards and fiberboards.)
|
| NF C46-500-2002
| 工業過程控制系統.帶氣壓輸出的閥位控制器性能評估方法
| (Industrial-process control systems - Methods of evaluating the performance of valve positioners with pneumatic outputs.)
|
| NF C46-502-1993
| 工業過程用調節閥.第1部分:術語和概論
| (Industrial-process control valves. Part 1 : control valve terminology and general considerations.)
|
| NF C46-503-1999
| 工業過程調節閥.第2-1部分:流量.在安裝條件下液體流量的截面方程
| (Industrial-process control valves. Part 2-1 : flow capacity. Sizing equations for fluid flow under installed conditions.)
|
| NF C46-505-1998
| 絕緣過程控制閥.第2-3部分:流量容量.試驗過程
| (Industrial-process control valves. Part 2-3 : flow capacity. Test procedures.)
|
| NF C46-506-1990
| 工業過程用調節閥.流量.流量的特性和校正的固有系數
| (Industrial-process control valves. Flow capacity. Inherent flow characteristics and rangeability.)
|
| NF C46-510-2001
| 工業過程控制閥.第3-1部分:尺寸.雙通球型直立式控制法蘭閥門的面對面尺寸和雙通球型角度控制法蘭閥門的中心
| (Industrial-process control valves - Part 3-1 : dimensions - Face-to-face dimensions for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-type, a)
|
| NF C46-511-2001
| 工業過程控制閥.第3-2部分:尺寸.蝶閥除外的旋轉控制閥門的面對面尺寸
| (Industrial-process control valves - Part 3-2 : dimensions - Face-to-face dimensions for rotary control valves except butterfly valves.)
|
| NF C46-512-1999
| 工業處理控制閥.第3-3部分:尺寸.對焊接的頭尾相接尺寸.兩接頭球型直接式控制閥(歐洲標準EN 60534-3-3)
| (Industrial-process control valves. Part 3-3 : dimensions. End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves.)
|
| NF C46-519-2001
| 工業過程控制閥.第8部分:噪聲考慮.第1節:實驗室測量氣動流經控制閥產生的噪聲
| (Industrial-process control valves - Part 8 : noise considerations - Section 1 : laboratory measurement of noise generated by aerodynamic flow through control valves.)
|
| NF C46-520-1993
| 工業過程控制閥.第8部分:噪聲問題.第2節:通過控制閥的液壓流動產生的噪聲的實驗室測量
| (Industrial-process control valves. Part 8 : noise considerations. Section 2 : laboratory measurement of noise generated by hydrodynamic flow through control valves.)
|
| NF C46-521-2001
| 工業過程控制閥.第8部分:噪聲問題.第3節:氣動控制閥噪聲預測法
| (Industrial-process control valves - Part 8-3 : noise considerations - Control valves aerodynamic noise prediction method.)
|
| NF C46-522-1994
| 工業處理控制閥.第8部分:噪聲條款.第4節:液壓流動產生的噪聲預定(EN 534-8-4)
| (Industrial-process control valves. Part 8 : noise considerations. Section 4 : prediction of noise generated by hydrodynamic flow.)
|
| NF C46-525-1991
| 工業過程用調節閥,調節閥門的限定柵屏
| (Industrial-process control valves. Control valve data sheet.)
|
| NF C46-531-2001
| 工業過程控制閥.第6-2部分:定位器裝到控制閥的安裝細則.旋轉傳動裝置上安裝的定位器
| (Industrial-process control valves - Part 6-2 : mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators.)
|
| NF C46-630-1998
| 工業過程控制閥.第6部分:控制閥與定位器連接用安裝細節.第1節:線性傳動裝置上安裝的定位器
| (Industrial-process control valves. Part 6 : mounting details for attachment of positioners to control valves. Section 1 : positioner mounting on linear actuators.)
|
| NF C47-738-2002
| 家用和類似用途的電氣自動控制器.第2-8部分:電動水閥的特殊要求,包括機械要求
| (Automatic electrical controls for household and similar use - Part 2-8 : particular requirements for electrically operated water valves, including mechanical requirements.)
|
| NF C47-746/A2-2001
| 家用和類似用途自動電控制裝置.第2部分:家用和類似用途漂浮型自動電氣水閥操作控制的特殊要求
| (Automatic electrical controls for household and similar use - Part 2-16 : particular requirements for automatic electrical water level controls of the float type for household and similar applications)
|
| NF C47-749-2002
| 家用和類似用途的電氣自動控制器.第2-19部分:電氣操作油閥門的特殊要求,包括機械要求
| (Automatic electrical controls for household and similar use - Part 2-19 : particular requirements for electrically operated oil valves, including mechanical requirements.)
|
| NF C52-123-1968
| 變壓器.介質液體的處理閥門
| (TRANSFORMERS. LIQUID DIELECTRIC DRAIN VALVES.)
|
| NF C53-254/A1-2003
| 送電和配電系統用電力電子設備.靜態無功功率補償裝置用晶閘管閥的試驗
| (Power electronics for electrical transmission and distribution and systems - Testing of thyristor valves for static VAR compensators.)
|
| NF C53-700-1-2002
| 高壓直流(HVDC)電力傳輸用可控硅閥門.第1部分:電氣試驗
| (Thyristor valves for high voltage direct current (HVDC) power transmission - Part 1 : electrical testing.)
|
| NF C53-700-1/A1-2003
| 高壓直流電(HVDC)傳輸用晶閘管閥的試驗.第1部分:電氣試驗
| (Testing of thyristor valves for high-voltage direct current (HVDC) transmission - Part 1 : electrical testing.)
|
| NF C58-432-1996
| 固定鉛酸蓄電池組.一般要求和試驗方法.第2部分:閥門調節型
| (Stationary lead-acid batteries. General requirements and methods of test. Part 2 : valve regulated types.)
|
| NF C58-561-2003
| 通用鉛酸蓄電池組(閥門調節型).第1部分:一般要求、功能特性.試驗方法
| (General purpose lead-acid batteries (valve-regulated types) - Part 1 : general requirements, functional characteristics - Methods of test.)
|
| NF C58-562-2003
| 通用鉛酸蓄電池組(閥門調節型).第2部分:尺寸、端子和標記
| (General purpose lead-acid batteries (valve-regulated types) - Part 2 : dimensions, terminals and marking.)
|
| NF D11-121-1988
| 丙烯制家用浴缸.浴缸閥安裝范圍的補充規范
| (BATHS FOR DOMESTIC PURPOSES MADE OF ACRYLIC MATERIAL. ADDITIONAL SPECIFICATION FOR THE MOUNTING OF TAPS ON BATHS.)
|
| NF D18-001-1965
| 衛生閥門.衛生設備用普通閥門.詞匯
| (SANITARY TAPS. SINGLE TAP FOR SANITARY APPLIANCES. TERMINOLOGY.)
|
| NF D18-201-1989
| 衛生設備管件.排放閥和混合閥的一般技術規范(公稱尺寸1/2)PN 10.最低水壓0.05MPa(0.5巴)
| (Sanitary tapware. General technical specifications for single taps and mixer taps (nominal size 1/2) pn 10. Minimum flow pressure of 0,05 MPa (0,5 bar).)
|
| NF D18-202-1984
| 衛生閥門.緩沖器.一般技術規范
| (SANITARY TAPWARE. MECHANICAL MIXERS. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF D18-203-1998
| 衛生閥門.靜熱混合閥門(PN10)一般技術規范(歐洲標準 EN 1111)
| (Sanitary tapware. Thermostatic mixing valves (PN 10). General technical specification.)
|
| NF D18-205-1989
| 衛生閥門.淋浴設備的附件.一般技術規范
| (SANITARY TAPS. SHOWER ACCESSORIES. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF D18-213-1996
| 衛生間管件.自動關閉閥PN 10
| (Sanitary tapware. Automatic shut-off valves pn 10.)
|
| NF D18-216-2003
| 衛生潔具.壓力沖洗閥和小便池自動關閉閥PN10
| (Sanitary tapware - Pressure flushing valves and automatic closing urinal valves PN 10.)
|
| NF D36-306-2002
| 氣體燃燒器和氣體器具的自動關閉閥
| (Automatic shut-off valves for gas burners and gas appliances.)
|
| NF D36-351-1969
| 家政學.使用氣體燃料的灶具和洗衣機用的錐形轉動閥門
| (TAPER TURNING COCKS FOR DOMESTIC COOKERS AND WASHING MACHINES USING GASEOUS FUELS.)
|
| NF D36-380-2001
| 燃氣燃燒器和燃氣用具用自動截止閥的閥門檢驗系統
| (Valve proving systems for automatic shut-off valves for gas burners and gas appliances.)
|
| NF D36-401-2000
| 建筑閥門.液壓安全裝置組.試驗和要求
| (Building valves - Hydraulic safety groups - Tests and requirements.)
|
| NF D36-402-2000
| 建筑閥門.膨脹組.試驗和要求
| (Building valves - Expansion groups - Tests and requirements.)
|
| NF D36-403-2000
| 建筑閥門.壓力安全閥.試驗和要求
| (Building valves - Pressure safety valves - Tests and requirements.)
|
| NF D36-404-2000
| 建筑閥門.溫度和壓力組合安全閥.試驗和要求
| (Building valves - Combined temperature and pressure relief valves - Tests and requirements.)
|
| NF D36-405-2000
| 建筑閥門.膨脹閥.試驗和要求
| (Building valves - Expansion valves - Tests and requirements.)
|
| NF D36-406-2004
| 建筑物用閥.建筑物內飲用水給水用手動銅合金和不銹鋼球閥.試驗和要求
| (Building valves - Manually operated copper alloy and stainless steel ball valves for potable water supply in buildings - Tests and requirements.)
|
| NF E29-003-1969
| 閥門關閉方向（閘板式閥門，閥式開關等）
| (DIRECTION OF CLOSURE FOR COCKS AND VALVES (SLUICE VALVES,SCREW DOWN VALVES,ETC.).)
|
| NF E29-019-1985
| 工業閥門制造.可拆卸的栓接法蘭盤.規范
| (Industrial valves. Threaded detachable flanges. Specifications.)
|
| NF E29-064-1946
| 閥門制造.帶活門的關閉閥.建筑物內閥門制造的專門術語
| (INDUSTRIAL VALVES. SCREW-DOWN STOPVALVES. TERMINOLOGY RELATING PARTICULARLY TO THE BUILDING TRADE.)
|
| NF E29-065-1946
| 閥門制造.帶活門的抽水閥門.建筑物內閥門制造的專門術語
| (INDUSTRIAL VALVES. TAPS. TERMINOLOGY RELATING PARTICULARLY TO THE BUILDING TRADE.)
|
| NF E29-066-1946
| 閥門制造抽汲閥.轉動式吸入閥和關閉閥.建筑物內閥門制造的專門術語
| (INDUSTRIAL VALVES. DRAW-OFF COCKS AND STOPCOCKS. TERMINOLOGY RELATING PARTICULARLY TO THE BUILDING TRADE.)
|
| NF E29-134-1978
| 家用管道燃氣設備用帶節氣閥并與陽端Ｇ１／２相連的雙連式安全開關
| (SAFETY RELEASE DEVICES WITH BUILT-IN STOP TAP AND TWO G 1/2 MALE UNION CONNECTIONS FOR DOMESTIC APPLIANCES USING MAINS GAS FUELS.)
|
| NF E29-138-1978
| 煤氣用具控制用，錐形轉動，有裝配式銅管路帶法蘭和Ｇ１／２連接管節的角形墻壁閥
| (FLANGED WALL VALVES,AT RIGHT ANGLES,FOR CONTROLLING GAS APPLIANCES,WITH TAPERED ROTATING SECTION,FOR BUILT-IN BRASS PIPING AND WITH G 1/2 CONNECTION.)
|
| NF E29-139-1998
| 建筑物氣體裝置用手工操作球閥和死底錐形旋塞
| (Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings.)
|
| NF E29-161-1943
| 支流閥.關閉閥和給水閥.總則.公稱壓力.標準壓力１０
| (BRANCH PIPE VALVES. STOPCOCKS AND DRAW-OFF COCKS. GENERAL. NOMINAL PRESSURE PN 10.)
|
| NF E29-162-1943
| 支流閥.關閉閥.公稱壓力，標準壓力１０
| (BRANCH PIPE VALVES. STOPCOCKS. NOMINAL PRESSURE PN 10.)
|
| NF E29-163-1943
| 支流閥.給水閥.公稱壓力，標準壓力１０
| (BRANCH PIPE VALVES. DRAW-OFF COCKS. NOMINAL PRESSURE PN 10.)
|
| NF E29-200-1-2002
| 法蘭及其連接件.按PN標注的管、閥門、配件和附件用圓形法蘭.鋼法蘭
| (Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1 : steel flanges.)
|
| NF E29-200-4-2002
| 法蘭及其連接件.按PN標注的管、閥門、配件和附件用圓形法蘭.第4部分:鋁合金法蘭
| (Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4 : aluminium alloy flanges.)
|
| NF E29-300-3-2003
| 閥門.外殼設計強度.第3部分:實驗方法
| (Valves - Shell design strength - Part 3 : experimental method.)
|
| NF E29-301-1-2000
| 工業閥門.對焊尾閥一端到另一端和中心到端面的尺寸
| (Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves.)
|
| NF E29-302-1-1996
| 法蘭管系統使用的金屬閥.面至面和中心至面的尺寸.第1部分:PN-指定閥
| (Industrial valves. Face-to-face and centre-to-face dimensions of matal valves for use in flanged pipe systems. Part 1 : pn-designated valves.)
|
| NF E29-303-1-2000
| 閥門.閥體、閥蓋和閥套用材料.第1部分:歐洲標準中規定的鋼
| (Valves - Materials for bodies, bonnets and covers - Part 1 : steels specified in European Standards.)
|
| NF E29-303-2-2000
| 閥門.閥體、閥蓋和閥套用材料.第2部分:歐洲標準中沒有規定的鋼
| (Valves - Materials for bodies, bonnets and covers - Part 2 : steels other than those specified in European Standards.)
|
| NF E29-303-3-2000
| 閥門.閥體、閥蓋和閥套用材料.第3部分:歐洲標準中規定的鑄鐵
| (Valves - Materials for bodies, bonnets and covers - Part 3 : cast iron specified in European Standards.)
|
| NF E29-303-4-2003
| 閥門.閥體、閥蓋和閥套用材料.第4部分:歐洲標準中規定的銅合金
| (Valves - Materials for bodies, bonnets and covers - Part 4 : copper alloys specified in European Standards.)
|
| NF E29-305-1999
| 工業閥門.鋼閥門對縫焊接末端.(歐洲標準EN 12627)
| (INDUSTRIAL VALVES. BUTT WELDING ENDS FOR STEEL VALVES. (EUROPEAN STANDARD EN 12627).)
|
| NF E29-306-1-1995
| 閥.術語.第1部分:閥型的定義
| (Valves. Terminology. Part 1 : definition of types of valves.)
|
| NF E29-306-2-1997
| 閥門.術語.第2部分:閥門元件的定義
| (VALVES. TERMINOLOGY. PART 2 : DEFINITION OF COMPONENTS OF VALVES. (EUROPEAN STANDARD EN 736-2).)
|
| NF E29-306-3-1999
| 閥門.術語.第3部分:術語的定義
| (VALVES. TERMINOLOGY. PART 3 : DEFINITION OF TERMS. (EUROPEAN STANDARD EN 736-3).)
|
| NF E29-306-3/A1-2001
| 閥門.術語.第3部分:術語定義
| (Valves - Terminology - Part 3 : definition of terms.)
|
| NF E29-308-1985
| 工業閥門.技術規范和協調訂貨證明書樣式
| (INDUSTRIAL VALVES. TECHNICAL SPECIFICATIONS AND CONFORMITY WITH ORDER ATTESTATION MODELS.)
|
| NF E29-309-2001
| 工業閥門.操作元件尺寸控制的方法
| (Industrial valves - Method for sizing the operating element.)
|
| NF E29-310-1992
| 通用工業閥的標記
| (Marking of general purpose industrial valves.)
|
| NF E29-311-1-2003
| 工業閥門.閥門試驗.第1部分:壓力試驗、試驗程序和驗收標準.強制性要求
| (Industrial valves - Testing of valves - Part 1 : pressure tests, test procedures and acceptance criteria - Mandatory requirements.)
|
| NF E29-311-1982
| 閥門.閥門制造設備的工廠壓力試驗
| (Valves. Factory pressure testing for valves.)
|
| NF E29-311-2-2003
| 工業閥門.閥門試驗.第2部分:試驗、試驗程序和驗收標準.補充標準
| (Industrial valves - Testing of valves - Part 2 : tests, test procedures and acceptance criteria - Supplementary criteria.)
|
| NF E29-313-1990
| 工業閥門.閥門輸送量的測定
| (Industrial valves. Determination of flow of valves. Case of compressible fluids.)
|
| NF E29-314-1986
| 閥門.試驗.術語.方法
| (VALVES. TESTS. NOMENCLATURE. METHODOLOGY.)
|
| NF E29-316-1-2000
| 供水用閥門.適用性要求和專用檢查試驗.第1部分:一般要求
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 1 : general requirements.)
|
| NF E29-316-2-2000
| 供水用閥門.適用性要求和專用檢查試驗.第2部分:隔離閥
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 2 : isolating valves.)
|
| NF E29-316-3-2000
| 供水用閥門.適用性要求和專用檢查試驗.第3部分:止回閥
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 3 : check valves.)
|
| NF E29-316-4-2000
| 供水閥門.特殊目的要求和適合驗證試驗的適配性. 第4部分:空氣閥門
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 4 : air valves.)
|
| NF E29-316-5-2001
| 供水用閥門.適用性要求和專用檢查試驗.第5部分:控制閥門
| (Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 5 : control valves.)
|
| NF E29-317-1999
| 工業閥門.化工和石油化工加工工業閥門.要求和試驗
| (Industrial valves - Valves for chemical and petrochemical process industry - Requirements and tests.)
|
| NF E29-318-2000
| 工業閥門.LNG隔絕閥門.合適性和驗證試驗規范
| (Industrial valves - Isolating valves for LNG - Specification for suitability and appropriate verification tests.)
|
| NF E29-319-2003
| 最大工作壓力為16bar及以下的配氣系統用閥.性能要求
| (Valves for gas distribution systems with maximum operating pressure less than or equal 16 bar - Performance requirements.)
|
| NF E29-321-1999
| 閥門.用水作為試驗液體的流動阻力試驗
| (Valves - Test of flow resistance using water as test fluid.)
|
| NF E29-330-2000
| 工業閥門.鋼插板閥門
| (Industrial valves - Steel gate valves.)
|
| NF E29-332-2003
| 工業用閥.鑄鐵閘閥
| (Industrial valves - Cast iron gate valves.)
|
| NF E29-334-2003
| 工業用閥門.銅合金閘閥
| (Industrial valves - Copper alloy gate valves.)
|
| NF E29-335-2003
| 石油和天然氣工業用尺寸為DN 100及更小的鋼閘閥、球閥和止回閥
| (Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries.)
|
| NF E29-350-2003
| 工業用閥.鋼制球閥、球狀截止閥和止回閥
| (Industrial valves - Steel globe and globe stop and check valves.)
|
| NF E29-354-2003
| 工業用閥.鑄鐵球閥
| (Industrial valves - Cast iron globe valves.)
|
| NF E29-372-2001
| 工業閥門.鑄鐵止回閥
| (Industrial valves - Cast iron check valves.)
|
| NF E29-373-1984
| 工業閥門.止回閥.鋼制，單搖板式，帶法蘭盤,ISO標準壓力16，20，25，40，50，100
| (Industrial valves. Flanged steel swing check valves. ISO PN A6, ISO PN 20, ISO PN 25, ISO PN 40, ISO PN 50, ISO PN 100.)
|
| NF E29-382-1981
| 工業閥門.加壓和放壓的加厚部件
| (Industrial valves. Drain hoss or pressure tap.)
|
| NF E29-383-1981
| 工業閥門.閘閥.旁路裝置
| (Industrial valves. Gate valve. By-pass.)
|
| NF E29-401-1996
| 工業閥門.多圈旋轉閥門驅動器附件
| (Industrial valves. Multi-turn valve actuator attachments.)
|
| NF E29-402-2001
| 工業閥門.部分回轉閥門致動器附件
| (Industrial valves - Part-turn valve actuator attachments.)
|
| NF E29-408-1992
| 工業用閥門.電力驅動器.規范
| (INDUSTRIAL VALVES. ELECTRIC ACTUATORS. SPECIFICATIONS.)
|
| NF E29-409-1992
| 工業閥門.氣動的和液壓的促動器.規范
| (INDUSTRIAL VALVES. PNEUMATIC AND HYDRAULIC ACTUATORS. SPECIFICATIONS.)
|
| NF E29-413-1989
| 工業閥門.安全閥流量計算.其他方法
| (INDUSTRIAL VALVE. SAFETY VALVES AND BURSTING DISC(S) DEVICES. CALCULATION OF THEORETICAL FLOWRATE.)
|
| NF E29-414-1992
| 工業閥門.安全閥門.安全閥門類型S,G1,L1和L2流率計算示例
| (INDUSTRIAL VALVES. SAFETY VALVES. EXAMPLES FOR FLOWRATE CALCULATION OF SAFETY VALVES TYPES S,G1,L1 AND L2.)
|
| NF E29-415-1990
| 工業閥門.安全閥.G平方型安全閥排出空氣當量流量計算實例.GPL標準蓄水池的應用
| (INDUSTRIAL VALVES. SAFETY VALVES. CALCULATION OF AIR EQUIVALENT FLOW CAPACITY FOR SAFETY VALVES OF TYPE G2. APPLICATION FOR STANDARD VESSELS FOR GPL.)
|
| NF E29-420-1985
| 工業閥門.安全閥.技術說明書樣式和協調證明書
| (INDUSTRIAL VALVES. SAFETY AND RELIEF VALVES. MODEL OF TECHNICAL SPECIFICATIONS AND CONFORMITY CERTIFICATE.)
|
| NF E29-421-1987
| 工業閥門.安全閥.安全膜.為獲得工作特性的安裝規范
| (Industrial valves. Safety valves. Bursting discs.)
|
| NF E29-425-1987
| 工業閥門.防爆膜裝置.定義.一般設計.試驗.分類.標記.調節
| (Industrial valves. Bursting discs devices. Definitions. General design. Test. Classification. Marking. Conditioning.)
|
| NF E29-430-1998
| 工業閥門.金屬蝶型閥門
| (Industrial valves. Metallic butterfly valves.)
|
| NF E29-440-1992
| 水蒸氣自動排泄閥.分類.(歐洲標準 EN 26704)
| (Automatic steam traps. Classification.) |
| NF E29-441-1992
| 水蒸氣自動排泄閥.標記(歐洲標準EN26553)
| (Automatic steam traps. Marking.)
|
| NF E29-443-1992
| 水蒸氣自動排泄閥.產品試驗和功能特性試驗(歐洲標準 EN 26948)
| (Automatic steam traps. Production and performance characteristics tests.)
|
| NF E29-445-1992
| 水蒸氣自動排泄閥.流量測定.試驗方法.(歐洲標準 EN 27842)
| (Automatic steam traps. Determination of discharge capacity. Test methods.)
|
| NF E29-453-2000
| 工業過程控制閥門
| (Industrial process control valves.)
|
| NF E29-465-1986
| 工業閥門.旋轉閥.銅鋁球閥.規范
| (INDUSTRIAL VALVES. CUPRO-ALUMINIUM BALL VALVES. SPECIFICATION.)
|
| NF E29-466-1987
| 工業閥門.旋轉閥.黃銅球閥.規范
| (INDUSTRIAL VALVES. BRASS BALL-VALVES. SPECIFICATIONS.)
|
| NF E29-480-1994
| 地下熱水管網的預隔熱管道系統.鋼制供水管道、聚氨基甲酸乙酯熱絕緣材料及高密度聚乙烯外殼的鋼閥門組件(歐
| (Preinsulated bonded pipe systems for underground hot water networks. Steelvalve assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene.)
|
| NF E29-492-2002
| 工業閥門.金屬材料的薄片閥
| (Industrial valves - Diaphragm valves made of metallic materials.)
|
| NF E29-648-1-1998
| 可運輸儲氣瓶.儲氣瓶和閥門材料與氣含量的相容性.第1部分:金屬材料
| (Transportable gas cylinders. Compatibility of cylinder and valve materials with gas contents. Part 1 : metallic materials.)
|
| NF E29-648-2-2001
| 可移動式液化氣鋼瓶.內有氣體的鋼瓶和閥材料的配合性.第2部分:非金屬材料
| (Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2 : non-metallic materials.)
|
| NF E29-648-3-1998
| 可運輸氣瓶.氣瓶和含氣閥門材料的可兼容性.第3部分:有氧環境中自燃試驗
| (Transportable gas cylinders. Compatibility of cylinder and valve materials with gas contents. Part 3 : autogenous ignition test in oxygen atmosphere.)
|
| NF E29-650-1992
| 氣瓶.閥出口連接
| (Gas cylinders. Valve outlet connections.)
|
| NF E29-661-1979
| 氯瓶上的鍛鋼閥門(最大容量60kg).公稱壓力25
| (FORGED-STEEL VALVES FOR CHLORINE CYLINDERS (MAX.CAPACITT 60 KG). NOMINAL PRESSURE PN 25.)
|
| NF E29-662-1979
| 呼吸保護裝置的壓縮氣瓶的閥門.使用壓力200bar.尺寸特性.標記
| (VALVES FOR COMPRESSED AIR CYLINDERS FOR RESPIRATORY PROTECTIVE EQUIPMENT. SERVICE PRESSURE 200 BAR. DIMENSIONAL CHARACTERISTICS. MARKING.)
|
| NF E29-663-1979
| 呼吸保護裝置的壓縮氣瓶的閥門.使用壓力300bar.尺寸特性.標記
| (VALUES FOR COMPRESSED AIR CYLINDERS FOR RESPIRATORY PROTECTIVE EQUIPMENT. SERVICE PRESSURE 300 BAR. DIMENSIONAL CHARACTER & STICS. MARKING.)
|
| NF E29-664-1979
| 氣瓶閥門出口.標準化提供的和使用中的裝置對照表
| (VALVE OUTLETS FOR GAS CYLINDERS. LIST OF STANDARD PROVISIONS OR THOSE IN USE.)
|
| NF E29-670-1998
| 可運輸儲氣瓶.儲氣瓶閥門配件
| (Transportable gas cylinders. Fitting of valves to gas cylinders.)
|
| NF E29-671-1981
| 氣瓶.閥門裝配錐體.總則
| (Gas cylinders. Taper screw thread for value stem and cylinder neck assembly. General.)
|
| NF E29-672-1-1999
| 氣瓶.氣瓶閥門連接用17E錐螺紋.第1部分:規范
| (Gas cylinders. 17E taper thread for connection of valves to gas cylinders. Part 1 : specifications.)
|
| NF E29-672-2-1999
| 氣瓶.閥門與氣瓶的連接用17E錐螺紋.第2部分:檢驗量規
| (Gas cylinders. 17E taper thread for connection of valves to gas cylinders. Part 2 : inspection gauges.)
|
| NF E29-674-1-1996
| 可運輸氣瓶.閥與氣瓶連接用25E錐形螺紋.第1部分:規范
| (Transportable gas cylinders. 25E taper thread for connection of valves to gas cylinders. Part 1 : specification.)
|
| NF E29-674-2-1996
| 可運輸氣瓶.閥與氣瓶連接用25E錐形螺紋.第2部分:量規檢查
| (Transportable gas cylinders. 25E taper thread for connection of valves to gas cylinders. Part 2 : gauge inspection.)
|
| NF E29-677-1981
| 氣瓶.閥門裝配錐體.公稱直徑28.3.錐度3/25.螺距1.814惠氏螺紋.檢驗規范
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER : 28,3. TAPER 3/25. 14 TPI SI. GAUGE REQUIREMENTS.)
|
| NF E29-678-1980
| 氣瓶.氣瓶閥門頸裝配螺紋錐體.公稱直徑16.4.錐度3/20.螺距14國際單位制
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 16,4,TAPER 3/20,14 TPI SI.)
|
| NF E29-679-1981
| 氣瓶.氣瓶閥門頸裝配錐體.公稱直徑16.4.錐度3/20.螺距14國際單位制.量規要求
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 16.4. TAPER 3/20. 14 TPI SI. GAUGE REQUIREMENTS.)
|
| NF E29-680-1980
| 氣瓶.閥桿和瓶頸組件用錐螺紋.公稱直徑25.8.錐度3/26(6°38`).螺距1.814國際單位制
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 25,8,TAPER 3/26 (6 DEGREES 38`,14 TPI SI)
|
| NF E29-681-1981
| 氣瓶.閥桿和瓶頸組件用錐螺紋.公稱直徑25.8.錐度3/26(6°C 38`).螺距1.814國際單位制.量規要求
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 25,8. TAPER 3/26 (6 DEGREES C 38`). 14 TP1 SI. GAUGE REQUIREMENTS.)
|
| NF E29-682-1980
| 氣瓶.閥桿和瓶頸組件用錐螺紋.公稱直徑34.錐度8.732％(5°).螺距為2國際單位制
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CULINDER NECK ASSEMBLY. NOMINAL DIAMETER 34 TAPER 8 732 PER CENT (5 DEGREES),PITCH 2 SI.)
|
| NF E29-683-1981
| 氣瓶.閥桿和瓶頸組件用錐螺紋.公稱直徑34.錐度8.736％(5°C).螺距為2國際單位制.量規要求
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 34. TAPER 8.736 PER CENT (5 DEGREES C). PITCH 2 SI. GAUGE ERQUIREMENTS.)
|
| NF E29-684-1980
| 氣瓶.閥桿和瓶頸組件用錐螺紋.公稱直徑26.錐度1/16(3°34`).螺距為1.814錐管螺紋
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 26,TAPER 1/16 (3 DEGREES 34`),14 TPI NPT.)
|
| NF E29-685-1981
| 氣瓶.閥桿和瓶頸組件用錐螺紋.公稱直徑26.錐度1/16(3°34`).螺距為1.814錐管螺紋.量規要求
| (GAS CYLINDERS. TAPER SCREW THREAD FOR VALVE STEM AND CYLINDER NECK ASSEMBLY. NOMINAL DIAMETER 26. TAPER 1/16 (3 DEGREES 34`). 14 TPI NPT. GAUGE REQUIREMENTS.)
|
| NF E29-686-1-2002
| 儲氣瓶.連接儲氣瓶閥門的平行螺紋.第1部分:規范
| (Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1: Specification.)
|
| NF E29-686-2-2002
| 儲氣瓶.連接儲氣瓶閥門的平行螺紋.第2部分:量規檢驗
| (Gas cylinders - Parallel threads for correction of valves to gas cylinders - Part 2 : Gauge inspection.)
|
| NF E29-690-1996
| 可運輸氣瓶.氣瓶閥.規范和型式試驗(EN 849)
| (Transportable gas cylinders. Cylinder valves. Specification and type testing.)
|
| NF E29-690/A2-2001
| 可移動的燃氣瓶.燃氣瓶閥門.規范和型式試驗
| (Transportable gas cylinders - Cylinder valves - Specification and type testing.)
|
| NF E29-691-1996
| 可運輸氣瓶.工業和醫用氣瓶用閥保護帽和閥罩.設計,安裝和試驗
| (Transportable gas cylinders - Valve protection caps and valve guards for industrial and medical gas cylinders - Design, construction and tests.)
|
| NF E29-691/A1-1999
| 可運輸儲氣瓶.工業用和醫用儲氣瓶用閥保護帽和閥護罩.設計、結構和試驗
| (Transportable gas cylinders - Valve protection caps and valve guards for industrial and medical gas cylinders - Design, construction and tests.)
|
| NF E29-691/A2-2000
| 便攜式氣瓶.工業和醫用氣瓶用閥門保護裝置.設計,結構和試驗
| (Transportable gas cylinders - Valve protection caps and valve guards for industrial and medical gas cylinders - Design, construction and tests.)
|
| NF E29-692-1-2001
| 氣瓶.微電子工業用氣瓶閥接頭.第1部分:輸出口接頭
| (Gas cylinders - Gas cylinder valve connections for use in the micro-electronics industry - Part 1 : outlet connections.)
|
| NF E29-692-2-2001
| 氣瓶.微電子工業用氣瓶閥接頭.第2部分:氣瓶閥接頭的規范和型式試驗
| (Gas cylinders - Gas cylinder valve connections for use in the microelectronics industry - Part 2 : specification and type testing for valve to cylinder connections.)
|
| NF E29-693-3-2001
| 氣體鋼瓶.壓縮呼吸空氣的氣體鋼瓶的出口連接.第3部分:230巴閥門適配器
| (Gas cylinders - Outlet connections for gas cylinder valves for compressed breathable air - Part 3 : adaptor for 230 bar valves.)
|
| NF E29-694-2001
| 可運輸氣瓶.氣瓶閥門.生產試驗和檢驗
| (Transportable gas cylinders - Gas cylinder valves - Manufacturing tests and inspections.)
|
| NF E29-695-2001
| 可運輸氣瓶.不可再充填的氣瓶用閥門.規范和原型試驗
| (Transportable gas cylinders - Cylinders valves for non-refillable cylinders - Specification and prototype testing.)
|
| NF E29-790-2003
| 便攜式燃具用帶或不帶閥門的一次性使用液化石油氣金屬氣瓶.制造、檢驗、試驗和標記
| (Non-refillable metallic gas cartridges for liquefied petroleum gases, with or without a valve, for use with portable appliances - Construction, inspection, testing and marking.)
|
| NF E29-796-2003
| 可運輸儲氣瓶.儲氣瓶定期檢查時氣瓶閥的檢查和維修
| (Transportable gas cylinders - Inspection and maintenance of cylinder valves at time of periodic inspection of gas cylinders.)
|
| NF E31-330-1-2000
| 燃油鍋爐用供油系統的安裝. 第1部分:安全要求和試驗.部件,進氣閥控制和安全裝置,供氣油罐
| (Installations for oil supply systems for oil burners - Part 1: safety requirements and tests : parts, oil feed pumps, control and safety devices, supply tanks.)
|
| NF E31-330-2-2000
| 燃油鍋爐用供油系統的安裝. 第2部分:安全要求和試驗.部件,閥門, 管道,過濾器,油充氣器,儀表
| (Installations for oil supply systems for oil burners - Part 2 : safety requirements and tests : parts, valves, pipes, filters, oil de-aerators, meters.)
|
| NF E32-110-10-2002
| 水管鍋爐和輔助設備.第10部分:防過壓安全閥的要求
| (Water-tube boilers and auxiliary installations - Part 10 : requirements for safeguards against excessive pressure.)
|
| NF E39-013-2003
| 區域供暖管道.直埋式熱水供應網用預隔熱連接的管道系統.聚氨酯隔熱和聚乙烯外覆層進宅鋼管用鋼閥門組件
| (District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Steel valve assembly for steel service pipes, polyurethane thermal insulation and outer casing of pol)
|
| NF E48-400-1996
| 液壓傳動.閥門裝配面及盒式閥腔的識別標志
| (HYDRAULIC FLUID POWER. CODE FOR IDENTIFICATION OF VALVE MOUNTING SURFACES AND CARTRIDGE VALVE CAVITIES.)
|
| NF E48-423-2001
| 液壓傳動.減壓閥、順序閥、卸載閥、節流閥和止回閥.裝配面
| (Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces.)
|
| NF E48-432-1993
| 液壓動力.4和5閥口伺服閥.安裝面
| (HYDRAULIC FLUID POWER. POUR- AND FIVE-PORTS SERVOVALVES. MOUNTING SURFACES.)
|
| NF E48-435-1998
| 液壓傳動.尺寸02、03和05的四端口模式排氣閥和四端口方向控制閥.夾緊尺寸
| (Hydraulic fluid power. Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05. Clamping dimensions.)
|
| NF E49-080-1-2002
| 氣壓液動.五通定向控制閥.第1部分:不帶電連接器的安裝接口
| (Pneumatic fluid power - Five-port directional control valves - Part 1 : mounting interfaces without electrical connector.)
|
| NF E49-080-2-2002
| 氣壓液動.五通方向控制閥.第2部分:任選電氣連接器的安裝接口面
| (Pneumatic fluid power - Five-port directional control valves - Part 2 : mounting interface surfaces with optional electrical connector.)
|
| NF E49-090-2-2003
| 氣壓傳動.18mm和26mm五氣口方向控制閥.第2部分:帶光學電接頭的安裝面
| (Pneumatic fluid power - Five-port directional control valves, sizes 18 mm and 26 mm - Part 2 : mounting interfaces with optional electrical connector.)
|
| NF E49-091-2002
| 氣壓傳動.控制閥和其它部件的孔口和控制機械的驗證
| (Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components.)
|
| NF E49-093-2003
| 氣壓傳動.3/2電磁閥.安裝接口表面
| (Pneumatic fluid power - 3/2 solenoid valves - Mounting interface surfaces.)
|
| NF E51-718-1998
| 建筑物通風.氣體終端設備.調節器和閥門的動力學試驗
| (Ventilation for buildings. Air terminal devices. Aerodynamic testing of dampers and valves.)
|
| NF E86-507-1999
| 制冷容器.制冷裝置閥(歐洲標準EN 1626)
| (Cryogenic vessels. Valves for cryogenic service.)
|
| NF E86-512-1-2002
| 冷凝容器.防超壓安全設施.第1部分:冷凝設備的安全閥
| (Cryogenic vessels - Safety devices for protection against excessive pressure - Part 1 : safety valves for cryogenic service.)
|
| NF E87-010-1976
| 輪胎充氣閥.術語
| (TYPE VALVES. TERMINOLOGY.)
|
| NF F11-806-1996
| 鐵路車輛.壓縮空氣電路用截止塞閥
| (RAILWAY ROLLING STOCK. SHUT-OFF PLUG VALVES, FOR COMPRESSED AIR CIRCUITS.)
|
| NF H44-012-1986
| 煙霧發生器.氣霧劑容器閥.１８mm皮碗
| (Aerosols dispensers. Valves. Ferrule 18 mm.)
|
| NF H44-013-1986
| 煙霧發生器.氣霧劑容器閥.２０mm皮碗
| (Aerosols dispensers. Valves. Ferrule 20 mm.)
|
| NF H44-015-1986
| 煙霧發生器.氣霧劑容器閥.１５mm皮碗
| (Aerosols dispensers. Valves. Ferrule 15 mm.)
|
| NF H44-020-1988
| 煙霧發生器.壓力分配容器（氣霧劑容器型）.氣霧劑容器上閥門的機械密封和安裝的快速試驗
| (AEROSOL DISPENSERS. RAPID TEST. TIGHTNESS OF VALVE MECHANISMS AND CLINCH.)
|
| NF H44-028-1986
| 煙霧劑發生器.氣霧劑閥.１７mm皮碗
| (AEROSOLS DISPENSERS. VALVES. FERRULE 17 MM.)
|
| NF H44-029-1986
| 煙霧劑發生器.氣霧劑閥.１３mm皮碗
| (AEROSOLS DISPENSERS. VALVES. FERRULE 13 MM.)
|
| NF H44-030-1986
| 煙霧劑發生器.氣霧劑閥.１１mm皮碗
| (AEROSOLS DISPENSERS. VALVES. FERRULE 11 MM.)
|
| NF J25-215-1969
| 造船工業.航海.船上閥門附件.桿的直徑和螺紋
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. SHANK DIAMETERS AND THREADS.)
|
| NF J25-220-1969
| 造船工業.航海.船上閥門附件.船首和手輪用方鋼
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. SQUARES FOR STEMS AND HANDWHEELS.)
|
| NF J25-255-1969
| 造船工業.航海.船上閥門附件.偏移手輪.尺寸.互換性
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. DISHED HANDWHEELS. DIMENSIONS. INTERCHANGEABILITY.)
|
| NF J25-274-1969
| 造船工業.航海.船上閥門附件.板手
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. CRANK HANDLES.)
|
| NF J25-308-1969
| 造船工業.船上閥門附件.填料箱.法蘭壓蓋.尺寸.互換性
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. STUFFING BOXES. GLANDS WITH FLANGE. DIMENSIONS. INTERCHANGEABILITY.)
|
| NF J25-310-1969
| 造船工業.航海.船上閥門附件.帶壓蓋和螺母的填料箱
| (SHIPBUILDING. MARINE NAVIGATION. MARINE VALVE ACCESSORIES. STUFFING BOXES WITH GLAND AND NUT.)
|
| NF J25-500-1958
| 造船工業.海水專用閥門.一般規范
| (SHIPBUILDING. SEA WATER VALVES. GENERAL SPECIFICATION.)
|
| NF J25-505-1958
| 造船工業.海水專用閥門.器材連接孔的位置
| (SHIPBUILDING. SEA WATER VALVES. ARRANGEMENT OF BODY ENDS.)
|
| NF J25-510-1958
| 造船工業.海水專用閥門.帶螺紋桿的連接閥.安裝Ｉ.部件名稱
| (SHIPBUILDING. SEA WATER VALVES. SCREW-DOWN STOP VALVES. PATTERN I. OPERATING MECHANISM. PARTS LIST.)
|
| NF J25-513-1958
| 造船工業.海水專用閥門.自由滑動式連接閥，安裝ＩＩ.部件名稱
| (SHIPBUILDING. SEA WATER VALVES. SHIP SIDE DISCHARGE VALVES. PATTERN II. OPERATING MECHANISM PARTS LIST.)
|
| NF J25-516-1958
| 造船工業.海水專用閥門.閉鎖式自由閥.安裝ＩＩＩ.部件名稱
| (SHIPBUILDING. SEA WATER VALVES. SCREW-DOWN STOP-AND-CHECK VALVES. PATTERN III. OPERATING MECHANISM. PARTS LIST.)
|
| NF J25-519-1958
| 造船工業.海水專用閥門.閉鎖式自由閥門.安裝ＩＶ.部件名稱
| (SHIPBUILDING. SEA WATER VALVES. SCREW-DOWN STOP-AND-CHECK VALVES WITH OPENING MECHANISM. PATTERN IV. OPERATING MECHANISM PARTS LIST.)
|
| NF J25-522-1958
| 造航工業.海水專用閥門.艙底吸水閥.組裝件.一般尺寸
| (SHIPBUILDING. SEA WATER VALVES. BILGE VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
| NF J25-526-1958
| 造船工業.海水專用閥門.船弦排水閥.組裝件.一般尺寸
| (SHIPBUILDING. SEA WATER VALVES. DISCHARGE VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
| NF J25-530-1958
| 造船工業.海水專用閥門.吸水收集箱.組裝件.一般尺寸
| (SHIPBUILDING. SEA WATER VALVES. SUCTION MANIFOLD VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
| NF J25-535-1958
| 造船工業.海水專用閥門.壓力收集箱.組裝件.一般尺寸
| (SHIPBUILDING. SEA WATER VALVES. DELIVERY MANIFOLD VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
| NF J38-540-2002
| 船舶和造船技術.載油艙用壓力/真空閥
| (Ships and marine technology - Pressure/vacuum valves for cargo tanks.)
|
| NF J41-410-1957
| 造船工業.“金士頓“閥門.一般規范
| (SHIPBUILDING. KINGSTON VALVES. GENERAL SPECIFICATION.)
|
| NF J41-415-1957
| 造船工業.“金士頓“閥門.總成.一般尺寸
| (SHIPBUILDING. KINGSTON VALVES. ASSEMBLY. GENERAL DIMENSIONS.)
|
| NF J41-416-1957
| 造船工業.“金士頓“閥門.標稱直徑５０－１７５號.部件名稱
| (SHIPBUILDING. KINGSTON VALVES,NOMINAL BORE 50-175 MM. NOMENCLATURE OF PARTS.)
|
| NF J41-417-1957
| 造船工業.“金士頓“閥門.標稱直徑２００－５００號.部件名稱
| (SHIPBUILDING. KINGSTON VALVES,NOMINAL BORE 200-500 MM. NOMENCLATURE OF PARTS.)
|
| NF J41-420-1957
| 造船工業.“金士頓“閥門.標稱直徑５０－１７５號.閥體
| (SHIPBUILDING. KINGSTON VALVES,NOMINAL BORE 50-175 MM. BODY.)
|
| NF J41-421-1957
| 造船工業.“金士頓“閥門.標稱直徑２００－５００號.閥體
| (SHIPBUILDING. KINGSTON VALVES,NOMINAL BORE 200-500 MM. BODY.)
|
| NF J41-425-1957
| 造船工業.“金士頓“閥門.卡箍
| (SHIPBUILDING. KINGSTON VALVES. BONNET.)
|
| NF J41-430-1957
| 造船工業.“金士頓“閥門.活門
| (SHIPBUILDING. KINGSTON VALVES. DISK.)
|
| NF J41-435-1957
| 造船工業.“金士頓“閥門.閥體環座
| (SHIPBUILDING. KINGSTON VALVES. BODY SEAT RING.)
|
| NF J41-440-1957
| 造船工業.“金士頓“閥門.閥桿
| (SHIPBUILDING. KINGSTON VALVES. STEM.)
|
| NF J41-445-1957
| 造船工業.“金士頓“閥門.上導桿.螺母鎖緊
| (SHIPBUILDING. KINGSTON VALVES. UPPER GUIDE. TAB WASHER.)
|
| NF J41-446-1957
| 造船工業.“金士頓“閥門.下導桿
| (SHIPBUILDING. KINGSTON VALVES. LOWER GUIDE.)
|
| NF J41-450-1957
| 造船工業.“金士頓“閥門.壓力填圈.壓蓋和襯套
| (SHIPBUILDING. KINGSTON VALVES. STUFFING BOX,GLAND AND BUSHING.)
|
| NF J41-455-1957
| 造船工業.“金士頓“閥門.手輪.套管
| (SHIPBUILDING. KINGSTON VALVES. HANDWHEEL. OPERATING SLEEVE.)
|
| NF J41-460-1957
| 造船工業.“金士頓“閥門.止動帽
| (SHIPBUILDING. KINGSTON VALVES. LOCKING SHACKLE.)
|
| NF J41-465-1957
| 造船工業.“金士頓“閥門.螺釘零件
| (SHIPBUILDING. KINGSTON VALVES. BOLTS AND SCREWS.)
|
| NF J41-470-1957
| 造船式為.“金士頓“閥門.加工.調節
| (SHIPBUILDING. KINGSTON VALVES. MACHINING. FITS.)
|
| NF J41-606-1993
| 造船工業.消防水管.消防閥門
| (SHIPBUILDING. FIRE HOSES. FIRE VALVES.)
|
| NF J45-780-1953
| 造船工業.帶自動閥的測量器.安裝組件
| (SHIPBUILDING. SOUNDING PIPES WITH SELF-ACTING VALVE. INSTALLATION ASSEMBLY.)
|
| NF J45-782-1953
| 造船工業.帶自動閥的測量頭.安裝組件
| (SHIPBUILDING. HEAD OF SOUNDING PIPES WITH SELF-ACTING VALVE. MOUNTING ASSEMBLY.)
|
| NF J45-784-1953
| 造船工業.帶自動閥的測量頭.盒子的零件
| (SHIPBUILDING. HEAD OF SOUNDING PIPES WITH SELF-ACTING VALVE. DETAILS OF BODY.)
|
| NF J45-788-1953
| 造船工業.帶自動閥的測量頭.零件
| (SHIPBUILDING. HEAD OF SOUNDING PIPES WITH SELF-ACTING VALVE. DETAILS.)
|
| NF J95-045-1998
| 小型船舶.船底閥和整個船體用配件.第1部分:金屬的
| (Small craft. Seacoks and through-hull fittings. Part 1 : metallic.)
|
| NF M41-016-1997
| 液化石油氣.丙烷干燥評定.閥門冷凍法
| (LIQUEFIED PETROLEUM GASES. ASSESSMENT OF THE DRYNESS OF PROPANE. VALVE FREEZE METHOD. (EUROPEAN STANDARD EN ISO 13758).)
|
| NF M62-301-4-2001
| 密封罩用組件.第4部分:通風和氣體清潔系統(如:過濾器和疏水閥)的安全和調節閥門以及控制和保護裝置
| (Components for containment enclosures - Part 4 : ventilation and gas-cleaning systems such as filters, traps, safety and regulation valves, control and protection devices.)
|
| NF M87-213-2001
| 石油和天然氣工業.下降孔設備.地下安全閥設備
| (Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment.)
|
| NF M87-400-1984
| 石油工業.帶外部桿和螺栓蓋的鋼制閥門.法蘭或焊接端點ＩＳＯＰＮ２０．ＩＳＯＰＮ４２０
| (Petroleum industry. Steel gate valves with-on flanges and joints. ISO PN 20 to ISO PN 420.)
|
| NF M87-401-1985
| 石油工業.閥門試驗和驗收檢查.耐壓性能
| (Petroleum industry. Acceptance testing and inspection of valves. Performance under pressure.)
|
| NF M87-402-1973
| 石油工業.帶鋼制法蘭硬塊密封物有斜座的閥門
| (PETROLEUM INDUSTRY. FLANGES AND SOLID WEDGE STEEL GATE-VALVES.)
|
| NF M88-114-1982
| 罐車.液化氣運輸.4-40ba工作壓力的DN50.DN80和DN100的止流和安全內部閥門
| (ROAD TANKERS. TRANSPORTATION OF LIQUEFIED GASES. INTERNAL STOP AND SAFETY OBTURATOR. NOMINAL DIAMETERS DN 50,DN 80 AND DN 100 FOR SERVICE PRESSURE BETWEEN 4 BAR AND 40 BAR.)
|
| NF M88-125-2001
| 危險貨物運輸罐.罐的配套設備.蒸汽轉移閥門
| (Tanks for transport of dangerous goods - Service equipment for tanks - Vapour transfer valve.)
|
| NF M88-127-2003
| 危險物品運輸用槽罐車.槽罐車用輔助設備.無壓平衡底閥
| (Tanks for transport of dangerous goods - Service equipment for tanks - Non pressure balanced footvalve.)
|
| NF M88-131-2003
| 危險物品運輸用槽罐車.槽罐車用輔助設備.壓力平衡底閥
| (Tanks for transport of dangerous goods - Service equipment for tanks - Pressure balanced footvalve.)
|
| NF M88-729-2003
| 自閉合式LPG氣瓶閥規范和試驗
| (Specification and testing of LPG cylinder valves - Self closing.)
|
| NF M88-729/A1-2003
| 自閉合式LPG氣瓶閥規范和試驗
| (Specification and testing of LPG cylinder valves - Self closing.)
|
| NF M88-730-2003
| 手控LPG氣瓶閥規范和試驗
| (Specification and testing of LPG cylinder valves - Manually operated.)
|
| NF M88-730/A1-2003
| 手控LPG氣瓶閥規范和試驗
| (Specification and testing of LPG cylinder valves - Manually operated.)
|
| NF M88-731-2003
| 液化石油氣(LPG)罐閥和配件的規范和試驗
| (Specification and testing for Liquefied Petroleum Gas (LPG) tank valves and fittings.)
|
| NF M88-737-2003
| 可運輸可再填充液化石油氣瓶用減壓閥
| (Pressure relief valves for transportable refillable cylinders for Liquefied Petroleum Gas (LPG).)
|
| NF M88-771-1975
| 液化烴容器裝置.手動截止閥.制造.功能.試驗
| (LIQUEFIED HYDROCARBON INSTALLATIONS IN CONTAINERS. MANUALLY CONTROLLED STOP VALVE. CONSTRUCTION. OPERATION. TESTS.)
|
| NF M88-773-1981
| 商用丁烷容器裝置.低壓固定調節的家用商品丁烷減壓閥
| (INSTALLATIONS BURNING COMMERCIAL BUTANE. PRESSURE REGULATOR TRIP,LOW-PRESSURE FIXED FLOW,FOR COMMERCIAL BUTANE FOR DOMESTIC USE.)
|
| NF M88-775-1990
| 裝液態碳氫化合物的鋼瓶.可移動部分和半移動部分用高壓可調減壓閥.功能.標記、試驗
| (LIQUEFIED HYDROCARBONS SYSTEMS IN CYLINDERS. FIXED ADJUSTEMENT,HIGH PRESSURE REGULATOR FOR MOBILE AND SEMI-MOBILE PREMISES. CONSTRUCTION. OPERATION, MARKING,TESTS.)
|
| NF P16-220-2003
| 排水系統用通氣閥.要求、試驗方法和合格評定
| (Air admittance valves for drainage systems - Requirements, tests methods and evaluation of conformity.)
|
| NF P16-260-4-2001
| 建筑物和現場用廢水提升裝置.施工和試驗原則.第4部分:無糞便廢水和含糞便物廢水用單向閥
| (Wastewater lifting plants for buildings and sites - Principles of construction and testing - Part 4 : non-return valves for faecal-free wastewater and wastewater containing faecal matter.)
|
| NF P40-500-2001
| 家庭計劃的閥門和配件的維修服務活動.有利于水消耗控制
| (Maintenance service activities for valves and fittings in housing schemes - Contribution to water consumption control.)
|
| NF P43-000-2003
| 建筑物閥門.建筑物中飲用水供應用銅合金節流閥.試驗要求.國家標準補充
| (Building valves - Copper alloy stopvalves for potable water supply in buildings - Tests and requirements - National complement.)
|
| NF P43-001-2000
| 建筑物用閥門.建筑物中供應引用水用銅合金截止閥.試驗和要求
| (Building valves - Copper alloy stopvalves for potable water supply in buildings - Tests and requirements.)
|
| NF P43-002-1981
| 建筑物水管閥門.水表截止閥.一般技術規范
| (VALVES AND TAPS FOR WATER SUPPLY IN BUILDINGS. STOP VALVES FOR METER. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF P43-003-1983
| 建筑物水管閥門.沖刷水箱閥門.一般技術規范
| (VALVES FOR BUILDING. BALL FLOAT VALVES FOR FLUSHING TANKS. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF P43-007-1985
| 建筑物水管閥門.A級控制非止回閥.一般技術規范
| (Valves and taps for water supply in buildings. Controllable check valves class A. General technical specifications.)
|
| NF P43-009-1988
| 建筑用供水閥門.自控帶中間溢流室的管路.技術規范
| (VALVES AND TAPS FOR BUILDINGS. NON CONTROLLABLE PIPE INTERRUPTOR WITH INTERMEDIATE DISCHARGE CHAMBER. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF P43-011-1985
| 建筑物水管閥門.非控制不同壓力范圍CB斷路器.一般技術規范
| (VALVES AND TAPS FOR WATER SUPPLY IN BUILDINGS. CB DISCONNECTORS WITH DIFFERENT NON CONTROLLABLE PRESSURE RANGES. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF P43-013-1988
| 建筑用水管閥門.斜通氣閥.通用技術規范
| (VALVES AND TAPS FOR BUILDINGS. INCLINE ANTI VACUUM VALVES (STRAIGHT OR ANGLED) DA. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF P43-014-1988
| 建筑物閥門.直流永久空氣接觸開關.一般技術規范
| (VALVES AND TAPS FOR BUILDING. PIPE INTERRUPTOR WITH PERMANENT ATMOSPHERIC CONTACT DC. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF P43-016-1985
| 建筑物水管閥門.“HA“端部斷路器.一般技術規范
| (VALVES AND TAPS FOR WATER SUPPLY IN BUILDINGS. HA ENDING DISCONNECTOR FOR TAPPING COCKS. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF P43-017-1989
| 建筑物水管閥門.帶法蘭可調EA止回閥.一般技術規范
| (VALVES AND TAPS FOR WATER SUPPLY IN BULDINGS. CONTROLLABLE CHECK VALVES EA,WITH FLANGES. GENERAL TECHNICAL SPECIFICATIONS.)
|
| NF P43-018-1990
| 建筑物水管閥門.飲用水衛生監測儀器.特性
| (VALVES AND TAPS FOR WATER SUPPLY IN BUILDINGS. CHECKING FITTING IN PLACE OF SANITARY PROTECTION UNITIES USED FOR DRINKING SUPPLY. SPECIFICATIONS.)
|
| NF P43-022-1988
| 建筑物水管閥門.AC分流溢出的設備.通用技術規范
| (VALVES AND TAPS FOR BUILDINGS. AIR GAP WITH DIVERTER AND OVERFLOW AC. GENERAL SPECIFICATIONS.)
|
| NF P43-023-1988
| 建筑物水管閥門.AD噴射溢出的設備.一般規范
| (VALVES AND TAPS FOR BUILDINGS. AIR GAP WITH INJECTOR AD. GENERAL SPECIFICATIONS.)
|
| NF P43-024-1988
| 建筑物水管閥門.AE衛生設施及設備.一般規范
| (VALVES AND TAPS FOR BUILDINGS. HYGIENIC AIR GAP AE. GENERAL SPECIFICATIONS.)
|
| NF P43-035-2000
| 建筑閥門.供水減壓閥和復合供水減壓閥.要求和試驗
| (Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests.)
|
| NF P50-746-2000
| 建筑物結構中的熱橋.線性熱閥門.簡化方法和無效閥門
| (Thermal bridges in building construction - Linear thermal transmittance - Simplified methods and default values.)
|
| NF P50-757-2000
| 建筑材料和產品.濕熱性能.列表設計的閥門
| (Building materials and products - Hygrothermal properties - Tabulated design values.)
|
| NF P52-001-1975
| 取暖設備用安全閥.一般技術規范
| (SAFETY VALVES FOR HEATING INSTALLATIONS.)
|
| NF P52-002-1-1989
| 散熱器恒溫閥.第1部分:試驗方法的要求
| (Thermostatic radiator valves. Part 1 : requirements and test methods.)
|
| NF R16-316-1989
| 道路車輛.帶凸緣和節流閥式試驗噴咀
| (Road vehicles. Calibrating nozzle, delay pintle type.)
|
| NF S31-014-1982
| 聲學.供水設施用液壓設備和閥門噪音的實驗室測量.第1部分:測量方法
| (ACOUSTICS. LABORATORY TESTS ON NOISE FORM TAPWARE AND HYDRAULIC EQUIPMENT USED IN WATER INSTALLATIONS. PART 1 : METHOD OF MEASUREMENT.)
|
| NF S31-014-3-1997
| 聲學.用于供水安裝的設備和應用的噪音發散的實驗室試驗.第3部分:內線閥門和應用的安裝和操作條件
| (Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Part 3 : mounting and operating conditions for in-line valves and appliances.)
|
| NF S31-014-4-1997
| 聲學.用于供水安裝的設備和用具中發散的噪音的實驗室試驗.第3部分:串聯式的閥門和用具的鑲嵌和操作條件
| (Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Part 4 : mounting and operating conditions for special appliances.)
|
| NF S52-728-1994
| 越野滑雪.扭距閥選擇
| (ALPINE SKI-BINDINGS. SELECTION OF RELEASE TORQUE VALUES.)
|
| NF S62-135-2001
| 固定式消防系統.氣體滅火系統用元件.第5部分:CO2系統用的高、低壓選擇器閥門及其起動器的要求和試驗方法
| (Fixed firefighting systems - Components for gas extinguishing systems - Part 5 : requirements and test methods for high and low pressure selector valves and their actuators for CO2 systems.)
|
| NF S62-143-2001
| 固定的消防系統.氣體滅火系統用元件.第13部分:止回閥的要求和試驗方法
| (Fixed firefighting systems - Components for gas extinguishing systems - Part 13 : requirements and test methods for check valves and non-return valves.)
|
| NF S62-222-1999
| 固定的消防系統.噴頭和噴水系統用元部件.第2部分:報警濕閥組件
| (Fixed firefighting systems - Components for sprinkler and water spray systems - Part 2 : wet alarm valve assemblies.)
|
| NF S62-222/A1-2001
| 固定滅火系統.噴頭和噴水系統用元部件.第2部分:報警濕閥組件
| (Fixed firefighting systems - Components for sprinkler and water spray systems - Part 2 : wet alarm valve assemblies.)
|
| NF S62-223-2000
| 固定滅火系統.自動灑水器和噴水系統用元件.第1部分:警報干閥組件
| (Fixed firefighting systems - Components for automatic sprinkler and water spray systems - Part 3 : dry alarm valves assemblies.)
|
| NF S62-223/A1-2001
| 固定滅火系統.噴頭和噴水系統用元部件.第3部分:報警干閥組件
| (Fixed firefighting systems - Components for sprinkler and water spray systems - Part 3 : dry alarm valve assemblies.)
|
| NF S76-017-1999
| 呼吸保護裝置.無吸入閥和有防止氣體或氣體微粒或只有微粒的分隔濾膜的半口罩.(歐洲標準EN 1827)
| (RESPIRATORY PROTECTIVE DEVICES. HALF MASKS WITHOUT INHALATION VALVES AND WITH SEPARABLE FILTERS TO PROTECT AGAINST GASES OR GASES AND PARTICLES OR PARTICLES ONLY. REQUIREMENTS, TESTING, MARKING. (EUROPEAN STANDARD EN 1827).)
|
| NF S76-024-1-2000
| 呼吸保護裝置.氣瓶閥.插入式連接器用螺紋接頭
| (Respiratory protective devices - Gas cylinder valves - Part 1 : thread connections for insert connector.)
|
| NF S76-024-1/A1-2003
| 呼吸防護裝置.氣瓶閥門.第1部分:旋入式連接器的螺紋連接件
| (Respiratory protective devices - Gas cylinder valves - Part 1 : thread connections for insert connector.)
|
| NF S76-024-2-1999
| 呼吸保護裝置.氣瓶閥.插座接頭
| (RESPIRATORY PROTECTIVE DEVICES. GAS CYLINDER VALVES. PART 2 : OUTLET CONNECTIONS. (EUROPEAN STANDARD EN 144-2).)
|
| NF S76-024-3-2003
| 呼吸保護器.氣瓶閥.第3部分:潛水硝基氣體和氧氣氣瓶的出口連接
| (Respiratory protective devices - Gas cylinder valves - Part 3 : outlet connections for diving gases Nitrox and oxygen.)
|
| NF S90-110-1996
| 便攜式氣瓶.醫用指針指示馬蹄型閥門排出口接頭
| (Transportable gas cylinders. Pin-index, yoke-type valve outlet connections for medical use.)
|
| NF S90-110/A1-2001
| 可移動的燃氣瓶.醫用定位銷轉位的卡箍式閥出口連接
| (Transportable gas cylinders - Pin-index, yoke-type valve outlet connections for medical use.)
|
| NF S94-201-2-1998
| 非活動外科植入物.血管和心臟植入物的特殊要求.包括心臟閥門管線的血管修補物
| (NON ACTIVE SURGICAL IMPLANTS. PARTICULAR REQUIREMENTS FOR CARDIAC AND VASCULAR IMPLANTS. PART 2 : VASCULAR PROSTHESES INCLUDING CARDIAC VALVE CONDUITS. (EUROPEAN STANDARD EN 12006-2).)
|
| NF S95-178-1998
| 醫用氣體用壓力調節器.第3部分:與鋼瓶閥門相結合的壓力調節器(歐洲標準EN 738-3)
| (PRESSURE REGULATORS FOR USE WITH MEDICAL GASES. PART 3 : PRESSURE REGULATORS INTEGRATED WITH CYLINDER VALVES. (EUROPEAN STANDARD EN 738-3).)
|
| NF S95-178/A1-2002
| 醫用氣體壓力調節器.第3部分:帶瓶閥的壓力調節器
| (Pressure regulators for use with medical gases - Part 3 : pressure regulators integrated with cylinder valves.)
|
| NF T54-015-1997
| 塑料管道系統.熱塑閥門.抗內壓和防泄漏的試驗方法
| (Plastics piping systems. Thermoplastics valves. Test methods for resistance to internal pressure and leaktightness.)
|
| NF T54-063-4-2003
| 供水用塑料管道系統.聚乙烯(PE).第4部分:閥
| (Plastics piping systems for water supply - Polyethylene (PE) - Part 4 : valves.)
|
| NF T54-065-4-2003
| 氣體燃料的塑料管道供應系統.聚乙烯(PE).第4部分:閥門
| (Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 4 : valves.)
|
| NF T54-082-1988
| 塑料.熱固塑料閥.耐壓和密封性試驗
| (PLASTICS. THERMOPLASTIC AND THERMOSETTING VALVES. TEST OF RESISTANCE TO PRESSURE.)
|
| NF T54-083-1991
| 熱塑料制閥門.轉矩.試驗方法.(歐洲標準EN 28233)
| (THERMOPLASTICS VALVES. TORQUE. TEST METHOD. (EUROPEAN STANDARD EN 28233).)
|
| NF T54-084-1991
| 熱塑料制閥門.耐疲勞強度.試驗方法.(歐洲標準EN 28659)
| (THERMOPLASTICS VALVES. FATIGUE STRENGTH. TEST METHOD. (EUROPEAN STANDARD EN 28659).)
|
| NF T54-100-1997
| 塑料管道系統.熱塑閥門.外部送風后閥門完好性的測試方法
| (Plastics piping systems. Thermoplastics valves. Test method for the integrity of a valve after an external blow.)
|
| NF T54-300-4-2003
| 普通用水、排水、污水地下和地上壓力系統用塑料管道系統.聚乙烯(PE).第4部分:閥門
| (Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 4 : valves.)
|
| NF T54-920-1997
| 塑料管道系統.聚乙烯管道系統用閥門.在工作機構彎頭處和彎頭之后的防漏試驗方法(歐洲標準EN 1680)
| (Plastics piping systems. Valves for polyethylene (PE) piping systems. Test method for leaktightness under and after bending applied to the operating mechanism.)
|
| NF T54-921-1997
| 塑料管道系統.熱塑閥門.彎曲下溫度周期變化后閥門完好性的測試方法
| (Plastics piping systems. Thermoplastics valves. Test method for the integrity of a valve after temperature cycling under bending.)
|
| NF T54-930-1997
| 塑料管道系統.聚乙烯(PE)閥.支架間耐彎曲試驗方法
| (Plastics piping systems. Polyethylene (PE) valves. Test method for resistance to bending between supports.)
|
| NF T54-932-1997
| 塑料管道系統.注模熱塑配件配件、閥和附屬設備.管道元件注模用熱塑材料長期液壓強度的測定
| (Plastics piping systems. Injection-moulded thermoplastics fittings, valves and ancillary equipment. Determination of the long-term hydrostatic strength of thermoplastics materials for injection moulding of piping components.)
|
| NF T54-934-1997
| 塑料管道系統.管件,閥和附件.氣流率/壓降關系的測定
| (Plastics piping systems. Fittings, valves and ancillaries. Determination of gaseous flow rate/pressure drop relationships.)
|
| NF T54-936-1997
| 塑料管道系統.聚乙烯(PE)閥.耐熱循環試驗方法(歐洲標準EN 12119)
| (Plastics piping systems. Polyethylene (PE) valves. Test method for resistance to thermal cycling.)
|
| NF T81-103-1980
| 液態體化學產品的運輸和裝卸.底部注入或排放的罐車.內部關閉閥和安全閥.使用壓力等于或小于４巴
| (TRANSPORTATION AND HANDLING OF LIQUID CHEMICAL PRODUCTS. TANKER VEHICLES FILLED AND EMPTIED FROM BELOW. INTERNAL SAFETY AND STOP VALVE. OPERATING PRESSURE EQUAL TO OR LESS THAN 4 BAR.)
|
| NF T81-104-1981
| 液態體化學產品的運輸和裝卸.底部注入或排放的罐車.４－４０bar工作壓力用標準尺寸ＤＮ８０和ＤＮ１００的
| (TRANSPORTATION AND HANDLING OF LIQUEFIED GASES. TANKER VEHICULES FILLED AND EMPTIED FROM BELOW. INTERNAL SAFETY GATES DN 80 AND DN 100 FOR OPERATING PRESSURES BETWEEN 4 BAR AND 40 BAR.)
|
| NF T81-151-1977
| 化學產品的運輸與裝卸.道路罐車.用銷或螺栓固定的閥門用圓蓋
| (TRANSPORTATION AND HANDLING OF CHEMICALS. ROAD TANKERS. CAPS FOR VALVES FIXED BY PINS OR BOLTS.)
|
| NF U51-421-1985
| 灌溉設備.容積閥.一般技術條件和試驗方法
| (IRRIGATION EQUIPMENT. VOLUMETRIC VALVES. GENERAL REQUIREMENTS AND TEST METHOD.)
|
| NF X08-102-1986
| 顏色.實驗室用閥門.液體鑒別通用顏色
| (Colours. Laboratory topware. Identification of fluids with conventional colours.)
|
| NF X42-129-2001
| 生物技術.管道和儀表的性能標準.第5部分:閥門
| (Biotechnology - Performance criteria for piping and instrumentation - Part 5 : valves.)
|
| NF X43-103-1996
| 空氣質量.氣味測量.污水氣味測量.超閥限方法
| (AIR QUALITY. OLFACTOMETRIC MEASUREMENTS. MEASUREMENT OF THE ODOUR OF A GAZEOUS EFFLUENT. SUPRA-THRESHOLD METHODS.)
|
| NF X50-001-7-1-2000
| 動力站設備和系統的征購指南.第7部分:管道和閥門.第1節:高壓管道系統
| (Guide for procurement of power station plant, equipement and systems - Part 7 : pipework and valves - Section 1 : high pressure piping systems.)
|
| NF X50-001-7-2-2000
| 動力站設備和系統的征購指南.第7部分:管道和閥門.第2節:鍋爐和高壓管道閥門
| (Guide for procurement of power station plant, equipment and systems - Part 7 : pipework and valves - Section 2 : boiler and high pressure piping valves.)
|
| XP E29-140-1999
| 使用氣體燃料的家用裝置的控制閥.安全控制閥(帶有集中自動密閉器的)
| (Control cocks for household appliances using gaseous fuels - Safety cocks (with integrated automatic obturator).)
|
| 編號 | 中文名稱 | 英文名稱 |
|---|